User guide
Table Of Contents
- User Guide
- Chapter 1
- Chapter 2
- Unpacking Your Touchmonitor
- Getting Started
- Connecting Your Touchmonitor
- Important:
- 1 Connect the video cable to the video connector on your PC. Secure the cable to your PC by turni...
- 2 Connect the power cable to the AC connector on your touchmonitor. To protect your equipment aga...
- 3 Connect the touchscreen cable. Determine if you have RS-232 or USB. Connect one end to the appr...
- 4 Power on your monitor using the Soft power switch and check that the power LED is on, then powe...
- 5 After a brief pause the picture should appear. If necessary, adjust the front panel controls ac...
- 6 Insert the Elo TouchTools CD-ROM in your computer’s CD-ROM drive to install the appropriate tou...
- Important:
- Installing the Driver Software
- Installing the Serial Touch Driver for Windows 2000, Me, 95/98 and NT 4.0
- Note:
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 Follow the directions on the screen to complete the driver setup for your version of Windows.
- 1 Click Start > Run.
- 2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
- 3 Click Open, then OK to run EloCd.exe.
- 4 Follow the directions on the screen to complete the driver setup for your version of Windows.
- Installing the USB Touch Driver for Windows 2000, Windows Me and Windows 98
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 Choose Next. Select “Search for the best driver for your device (Recommended)” and choose Next.
- 3 When a list of search locations is displayed, place a checkmark on “Specify a location” and use...
- 4 Choose Next. Once the Elo TouchSystems USB touchscreen driver has been detected, choose Next ag...
- 5 You will see several files being copied. Insert your Windows 98 CD if prompted. Choose Finish.
- Note
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the ...
- 3 Follow the directions on the screen to complete the driver setup for your version of Windows.
- 1 Click Start > Run.
- 2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
- 3 Click Open, then OK to run EloCd.exe.
- 4 Follow the directions on the screen to complete the driver setup for your version of Windows.
- Chapter 3
- About Touchmonitor Adjustments
- Touchmonitor Controls
- Using the On Screen Display (OSD)
- 1 Push the MENU button to access the OSD. The resolution and frequency are displayed at the top o...
- 2 Push the or button to choose the item you want to adjust. The selected item is highlighted.
- 3 Push the SELECT button to adjust the highlighted item.
- 4 Push the or button to adjust the selection.
- 5 Push the SELECT button to return to the previous menu if you are in a submenu.
- Brightness
- Contrast
- OSD Adjustments
- Note:
- Using the On Screen Display (OSD)
- Chapter 4
- Appendix A
- Appendix B
- Regulatory Information
- Appendix C
- Warranty
- Index
- Guide d’utilisation
- GARANTIE
- Index
- Gebrauchsanweisung
Index-39
A
A propos des réglages de l'écran tactile 11
A propos du produit 1
B
Brillant 31, 32
C
Commandes de l'écran tactile 12
Compabilité Plug and Play 30
Configuration du signal des écrans de 15" et de 17" 33
Connexion de l'écran tactile 5
Consignes de sécurité à propos de l'écran tactile 23
Consignes de sécurité en matière d'électricité 25
Consommation électrique 29, 34
Construction 32
Contraste 15
Contrôle des couleurs 15
Couleurs d’affichage 29
D
Déballage du moniteur tactile 3
Densité du point de contact 31, 32
Dépannage 17
Dimensions du moniteur 30
Durabilité de la surface 31, 32
Durée de vie du CRT 30
Durée de vie prévue 31, 32
E
Ecrans tactiles :
Aperçu19
Ecrans tactiles AccuTouch 21
Ecrans tactiles IntelliTouch 20
Effet de coussin 14
Effet de voile 14
EMI 30
Emissions et immunité 25
Entretien et manipulation de votre écran tactile 24
Ergonomie 30
Etanchéité 31
F
Fiche technique 29
Fonctionnement 11
Force d’activation tactile 31, 32
Fréquence de déviation 29
G
Garantie 37
Gestion de l'alimentation 29
H
Humidité 30
I
Information 15
Installation 3
Installation du pilote 8
Installation du pilote Serial Touch pour Windows 2000, Me,
95/98 et NT 4.0 9
Installation du pilote USB Touch Driver pour Windows
2000, Me et Windows 98 10
Installation du socle 4
Introduction 1
L
Langue 14
Largeur de bande d’entrée vidéo maximum 29
Luminosité 15
M
Messages d'avertissement de moniteur 18
Mise en route 4
Modes préréglés34
Moiré H. 14
Moiré V. 14
P
Parallélogramme 14
Poids net 30
Position H. 14
Position H. OSD 14
Position V. 14
Précautions 1
Précision du positionnement 31, 32
Protection électrostatique 31
R
Rappel 15
Réglages à l’écran 30
Réglages OSD 14
Index