User guide
Table Of Contents
- User Guide
- Chapter 1
- Chapter 2
- Unpacking Your Touchmonitor
- Getting Started
- Connecting Your Touchmonitor
- Important:
- 1 Connect the video cable to the video connector on your PC. Secure the cable to your PC by turni...
- 2 Connect the power cable to the AC connector on your touchmonitor. To protect your equipment aga...
- 3 Connect the touchscreen cable. Determine if you have RS-232 or USB. Connect one end to the appr...
- 4 Power on your monitor using the Soft power switch and check that the power LED is on, then powe...
- 5 After a brief pause the picture should appear. If necessary, adjust the front panel controls ac...
- 6 Insert the Elo TouchTools CD-ROM in your computer’s CD-ROM drive to install the appropriate tou...
- Important:
- Installing the Driver Software
- Installing the Serial Touch Driver for Windows 2000, Me, 95/98 and NT 4.0
- Note:
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 Follow the directions on the screen to complete the driver setup for your version of Windows.
- 1 Click Start > Run.
- 2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
- 3 Click Open, then OK to run EloCd.exe.
- 4 Follow the directions on the screen to complete the driver setup for your version of Windows.
- Installing the USB Touch Driver for Windows 2000, Windows Me and Windows 98
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 Choose Next. Select “Search for the best driver for your device (Recommended)” and choose Next.
- 3 When a list of search locations is displayed, place a checkmark on “Specify a location” and use...
- 4 Choose Next. Once the Elo TouchSystems USB touchscreen driver has been detected, choose Next ag...
- 5 You will see several files being copied. Insert your Windows 98 CD if prompted. Choose Finish.
- Note
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the ...
- 3 Follow the directions on the screen to complete the driver setup for your version of Windows.
- 1 Click Start > Run.
- 2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
- 3 Click Open, then OK to run EloCd.exe.
- 4 Follow the directions on the screen to complete the driver setup for your version of Windows.
- Chapter 3
- About Touchmonitor Adjustments
- Touchmonitor Controls
- Using the On Screen Display (OSD)
- 1 Push the MENU button to access the OSD. The resolution and frequency are displayed at the top o...
- 2 Push the or button to choose the item you want to adjust. The selected item is highlighted.
- 3 Push the SELECT button to adjust the highlighted item.
- 4 Push the or button to adjust the selection.
- 5 Push the SELECT button to return to the previous menu if you are in a submenu.
- Brightness
- Contrast
- OSD Adjustments
- Note:
- Using the On Screen Display (OSD)
- Chapter 4
- Appendix A
- Appendix B
- Regulatory Information
- Appendix C
- Warranty
- Index
- Guide d’utilisation
- GARANTIE
- Index
- Gebrauchsanweisung
26 Elo Entuitive Touchmonitor Guide de l’utilisateur
D) Information générale à l'intention de tous les utilisateurs : Cet équipement
génère, utilise et peut irradier de l'énergie radioélectrique. S'il n'est pas installé et
utilisé selon les directives de ce manuel, l'équipement peut provoquer des
interférences nuisibles aux communications radio et télévision. Il n'est cependant
pas garanti qu'aucune interférence ne se produira dans une installation spécifique
en raison de facteurs propres au site en question.
1) Pour se conformer aux exigences sur les émissions radioélectriques, l'utili-
sateur doit adopter les mesures suivantes :
a) Utiliser uniquement les câbles E/S fournis pour relier l'appareil
numérique à un ordinateur.
b) Pour assurer la conformité, utiliser uniquement le cordon d'alimenta-
tion fourni et approuvé par le fabricant.
c) Tout changement ou toute modification n'étant pas expressément
approuvée par la partie se portant garante de la conformité est suscepti-
ble d'annuler le droit de l'utilisateur à faire fonctionner l'équipement.
2) Si cet équipement semble perturber les réceptions de télévision ou de radio
ou de tout autre appareil :
a) Vérifiez si votre appareil est la source de la perturbation en l'éteignant
puis en le rallumant.
b) Si vous déterminez que c'est cet équipement qui est à l'origine de
l'interférence, vous pouvez essayer de supprimer l'interférence en adop-
tant l'une ou plusieurs des mesures suivantes :
i) Eloignez l'appareil numérique du récepteur touché.
ii) Réorientez (tournez) l'appareil numérique par rapport au récep-
teur touché.
iii) Réorientez l'antenne du récepteur touché.
iv) Branchez l'appareil numérique dans un secteur différent n'appar-
tenant pas au circuit auquel le récepteur est connecté.
v) Déconnectez et retirez les câbles E/S que l'appareil numérique
n'utilise pas. (Des câbles E/S sans terminaison sont une source
potentielle de niveaux d'émissions radioélectriques élevés.)
vi) Branchez l'appareil numérique dans une prise de courant mise à
la terre. N'utilisez pas des fiches d'adaptateur CA. (Le retrait ou la
coupure du fil de terre peut augmenter les niveaux d'émissions
radioélectriques et peut aussi poser un risque de choc électrique
fatal.)
Si vous avez besoin d'aide, consultez votre revendeur, fabricant ou
technicien radio/télévision expérimenté.