User guide
Table Of Contents
- User Guide
- Chapter 1
- Chapter 2
- Unpacking Your Touchmonitor
- Getting Started
- Connecting Your Touchmonitor
- Important:
- 1 Connect the video cable to the video connector on your PC. Secure the cable to your PC by turni...
- 2 Connect the power cable to the AC connector on your touchmonitor. To protect your equipment aga...
- 3 Connect the touchscreen cable. Determine if you have RS-232 or USB. Connect one end to the appr...
- 4 Power on your monitor using the Soft power switch and check that the power LED is on, then powe...
- 5 After a brief pause the picture should appear. If necessary, adjust the front panel controls ac...
- 6 Insert the Elo TouchTools CD-ROM in your computer’s CD-ROM drive to install the appropriate tou...
- Important:
- Installing the Driver Software
- Installing the Serial Touch Driver for Windows 2000, Me, 95/98 and NT 4.0
- Note:
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 Follow the directions on the screen to complete the driver setup for your version of Windows.
- 1 Click Start > Run.
- 2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
- 3 Click Open, then OK to run EloCd.exe.
- 4 Follow the directions on the screen to complete the driver setup for your version of Windows.
- Installing the USB Touch Driver for Windows 2000, Windows Me and Windows 98
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 Choose Next. Select “Search for the best driver for your device (Recommended)” and choose Next.
- 3 When a list of search locations is displayed, place a checkmark on “Specify a location” and use...
- 4 Choose Next. Once the Elo TouchSystems USB touchscreen driver has been detected, choose Next ag...
- 5 You will see several files being copied. Insert your Windows 98 CD if prompted. Choose Finish.
- Note
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the ...
- 3 Follow the directions on the screen to complete the driver setup for your version of Windows.
- 1 Click Start > Run.
- 2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
- 3 Click Open, then OK to run EloCd.exe.
- 4 Follow the directions on the screen to complete the driver setup for your version of Windows.
- Chapter 3
- About Touchmonitor Adjustments
- Touchmonitor Controls
- Using the On Screen Display (OSD)
- 1 Push the MENU button to access the OSD. The resolution and frequency are displayed at the top o...
- 2 Push the or button to choose the item you want to adjust. The selected item is highlighted.
- 3 Push the SELECT button to adjust the highlighted item.
- 4 Push the or button to adjust the selection.
- 5 Push the SELECT button to return to the previous menu if you are in a submenu.
- Brightness
- Contrast
- OSD Adjustments
- Note:
- Using the On Screen Display (OSD)
- Chapter 4
- Appendix A
- Appendix B
- Regulatory Information
- Appendix C
- Warranty
- Index
- Guide d’utilisation
- GARANTIE
- Index
- Gebrauchsanweisung
C-29
A NHANG
C
C
HAPTER
4
T
ECHNISCHE
D
ATEN
H
INWEIS
:
Alle technischen Daten können geändert werden.
Technische Daten des Touchmonitors
17-Zoll-Monitor 15-Zoll-Monitor
Bildröhre
17 Zoll (15,7 sichtbare
Bildschirmdiagonale), 0,27 mm
Punktbreite, antistatisch, entspiegelt,
TCO-Beschichtung
15 Zoll (13,8 sichtbare
Bildschirmdiagonale), 0,28 mm
Punktbreite, antistatisch, entspiegelt,
Mehrlagenbeschichtung
Maximale Auflösung
1280 x 1024 bei 60 Hz 1280 x 1024 bei 60 Hz
Ablenkfrequenz
Horizontal: 30-70 kHz
Vertikal: 50-150 Hz
Horizontal: 30-70 kHz
Vertikal: 50-150 Hz
Maximale
Videoeingangsbandbreite
108 MHz 108 MHz
Anzeigebereich*
Werkseinstellung
etwa 305 mm x 229 mm
Werkseinstellung
etwa 260 mm x 195 mm
Eingangssignal
RGB analog, 15-Stift-D-Sub RGB analog, 15-Stift-D-Sub
Eingangsspannung
100 - 240 V WS, 1,5 A 100 - 240 V WS, 1,3 A
Anzeigefarben*
Analogeingabe, beliebig viele Farben Analogeingabe, beliebig viele Farben
Stromverbrauch
80 Watt 75 Watt
Stromsparfunktion
Entspricht EPA/Energy Star, NUTEK/
TCO VESA DPMS
Signalgebungsmethode
Entspricht EPA/Energy Star, VESA
DPMS Signalgebungsmethode
Betriebsfertig
Entspricht VESA DDC 1/2B Standards Entspricht VESA DDC 1/2B
Standards