User guide
Table Of Contents
- User Guide
- Chapter 1
- Chapter 2
- Unpacking Your Touchmonitor
- Getting Started
- Connecting Your Touchmonitor
- Important:
- 1 Connect the video cable to the video connector on your PC. Secure the cable to your PC by turni...
- 2 Connect the power cable to the AC connector on your touchmonitor. To protect your equipment aga...
- 3 Connect the touchscreen cable. Determine if you have RS-232 or USB. Connect one end to the appr...
- 4 Power on your monitor using the Soft power switch and check that the power LED is on, then powe...
- 5 After a brief pause the picture should appear. If necessary, adjust the front panel controls ac...
- 6 Insert the Elo TouchTools CD-ROM in your computer’s CD-ROM drive to install the appropriate tou...
- Important:
- Installing the Driver Software
- Installing the Serial Touch Driver for Windows 2000, Me, 95/98 and NT 4.0
- Note:
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 Follow the directions on the screen to complete the driver setup for your version of Windows.
- 1 Click Start > Run.
- 2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
- 3 Click Open, then OK to run EloCd.exe.
- 4 Follow the directions on the screen to complete the driver setup for your version of Windows.
- Installing the USB Touch Driver for Windows 2000, Windows Me and Windows 98
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 Choose Next. Select “Search for the best driver for your device (Recommended)” and choose Next.
- 3 When a list of search locations is displayed, place a checkmark on “Specify a location” and use...
- 4 Choose Next. Once the Elo TouchSystems USB touchscreen driver has been detected, choose Next ag...
- 5 You will see several files being copied. Insert your Windows 98 CD if prompted. Choose Finish.
- Note
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the ...
- 3 Follow the directions on the screen to complete the driver setup for your version of Windows.
- 1 Click Start > Run.
- 2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
- 3 Click Open, then OK to run EloCd.exe.
- 4 Follow the directions on the screen to complete the driver setup for your version of Windows.
- Chapter 3
- About Touchmonitor Adjustments
- Touchmonitor Controls
- Using the On Screen Display (OSD)
- 1 Push the MENU button to access the OSD. The resolution and frequency are displayed at the top o...
- 2 Push the or button to choose the item you want to adjust. The selected item is highlighted.
- 3 Push the SELECT button to adjust the highlighted item.
- 4 Push the or button to adjust the selection.
- 5 Push the SELECT button to return to the previous menu if you are in a submenu.
- Brightness
- Contrast
- OSD Adjustments
- Note:
- Using the On Screen Display (OSD)
- Chapter 4
- Appendix A
- Appendix B
- Regulatory Information
- Appendix C
- Warranty
- Index
- Guide d’utilisation
- GARANTIE
- Index
- Gebrauchsanweisung
2-6 Elo Entuitive Touchmonitor Gebrauchsanweisung
2 Schließen Sie das Netzkabel an den Netzanschluß des Touchmonitors an.
Zum Schutz des Geräts gegen Überspannung empfiehlt es sich, das
Netzkabel des Touchmonitors an einen Überspannungsschutz und den
Überspannungsschutz an eine geerdete Schutzkontakt-Netzsteckdose
anzuschließen.
Befestigtes Videokabel
Netzkabel