User guide
Table Of Contents
- User Guide
- Chapter 1
- Chapter 2
- Unpacking Your Touchmonitor
- Getting Started
- Connecting Your Touchmonitor
- Important:
- 1 Connect the video cable to the video connector on your PC. Secure the cable to your PC by turni...
- 2 Connect the power cable to the AC connector on your touchmonitor. To protect your equipment aga...
- 3 Connect the touchscreen cable. Determine if you have RS-232 or USB. Connect one end to the appr...
- 4 Power on your monitor using the Soft power switch and check that the power LED is on, then powe...
- 5 After a brief pause the picture should appear. If necessary, adjust the front panel controls ac...
- 6 Insert the Elo TouchTools CD-ROM in your computer’s CD-ROM drive to install the appropriate tou...
- Important:
- Installing the Driver Software
- Installing the Serial Touch Driver for Windows 2000, Me, 95/98 and NT 4.0
- Note:
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 Follow the directions on the screen to complete the driver setup for your version of Windows.
- 1 Click Start > Run.
- 2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
- 3 Click Open, then OK to run EloCd.exe.
- 4 Follow the directions on the screen to complete the driver setup for your version of Windows.
- Installing the USB Touch Driver for Windows 2000, Windows Me and Windows 98
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 Choose Next. Select “Search for the best driver for your device (Recommended)” and choose Next.
- 3 When a list of search locations is displayed, place a checkmark on “Specify a location” and use...
- 4 Choose Next. Once the Elo TouchSystems USB touchscreen driver has been detected, choose Next ag...
- 5 You will see several files being copied. Insert your Windows 98 CD if prompted. Choose Finish.
- Note
- 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive.
- 2 If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the ...
- 3 Follow the directions on the screen to complete the driver setup for your version of Windows.
- 1 Click Start > Run.
- 2 Click the Browse button to locate the EloCd.exe program on the CD-ROM.
- 3 Click Open, then OK to run EloCd.exe.
- 4 Follow the directions on the screen to complete the driver setup for your version of Windows.
- Chapter 3
- About Touchmonitor Adjustments
- Touchmonitor Controls
- Using the On Screen Display (OSD)
- 1 Push the MENU button to access the OSD. The resolution and frequency are displayed at the top o...
- 2 Push the or button to choose the item you want to adjust. The selected item is highlighted.
- 3 Push the SELECT button to adjust the highlighted item.
- 4 Push the or button to adjust the selection.
- 5 Push the SELECT button to return to the previous menu if you are in a submenu.
- Brightness
- Contrast
- OSD Adjustments
- Note:
- Using the On Screen Display (OSD)
- Chapter 4
- Appendix A
- Appendix B
- Regulatory Information
- Appendix C
- Warranty
- Index
- Guide d’utilisation
- GARANTIE
- Index
- Gebrauchsanweisung
2-5
Anschließen des Touchmonitors
Der Touchmonitor wird mit einem der folgenden Tastbildschirm-
Anschlußkabel geliefert: Serielles (RS-232) oder USB-Kabel (nur für Windows
98 und Windows 2000).
W
ICHTIG
:
Vergewissern Sie sich vor dem Anschließen der Kabel am Touchmonitor und am PC,
daß der Touchmonitor und der Rechner ausgeschaltet sind.
1 Schließen Sie das Videokabel an den Videoanschluß des PCs an. Befestigen
Sie das Kabel am PC, indem Sie die Schrauben des Anschlußsteckers
festziehen.
Befestigtes Videokabel