USER MANUAL Elo Touch Solutions 2440L Touchmonitor SW602154 Rev A
Copyright © 2013 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc. Disclaimer The information in this document is subject to change without notice. Elo Touch Solutions, Inc.
Table of Contents Chapter 1: Introduction ............................................................................ 4 Chapter 2: Installation .............................................................................. 5 Chapter 3: Mounting ............................................................................... 13 Chapter 4: Operation .............................................................................. 16 Chapter 5: Technical Support ...................................................
Chapter 1: Introduction Product Description Your new touchmonitor combines the reliable performance of Elo Touch Solutions touch products with the latest developments in touchscreen technology and display design. This combination of features ensures a product with stable, drift-free operation, consistent reliability and durability, backed by a 3-year standard warranty. This open-frame touchmonitor delivers a professional-grade display in a slim, integrated package.
Chapter 2: Installation Unpacking the Touchmonitor Open the carton and verify that the following items are present: • Touchmonitor with protective sheet for its face • User Manuals CD • Japanese language regulatory information pamphlet • Quick Install Guide • VGA cable • DVI cable • USB cable (not available for no touch models) • Serial cable (available for single touch models only) • Mounting brackets and screws • OSD Remote User Manual: 2440L SW602154 Rev A, Page 5 of 34
Connector Panel & Interfaces Touchmonitor Connections 1. Connect the DVI or VGA video cables between the monitor’s DVI/VGA input connectors and your DVI/VGA video source. Tighten the video cable’s screws for best performance. 2. Connect the USB or serial touch cable between the monitor’s USB/serial connector and your PC’s USB/serial port. 3. Connect a 12VDC power supply to the monitor’s input power jack. 4. The touchmonitor ships in an ON state, video should be displayed on your monitor already.
Installing the Touch Technology Software Drivers Some software installation is required for your touchmonitor to work with your computer. No additional drivers are required for your projected-capacitive touchmonitor, it uses Windows HID drivers. The drivers are available on the Elo Touch Solutions website. Visit www.elotouch.
Select the applicable driver from the Elo Touch Solutions website and download: For Windows 7 installations, double-click on EloSetup Installer User Manual: 2440L SW602154 Rev A, Page 8 of 34
After accepting the end-user license agreement, the system will initialize to setup installation of drivers. To complete setup, reboot system by clicking on “Reboot Now” button. Click on “One More Minute” if more time is needed with increments of 1 minute.
Note: System will automatically reboot when “Time left” counter reaches “0”.
Click on “Unzip” button to unzip files.
Select one or more of the drivers to install. Click on “Next” After accepting the end-user license agreement, the drivers will finish installing. Reboot your computer after the install is complete.
Chapter 3: Mounting General Mounting Information The OSD text can be rotated through the OSD menu to better suit your mounting orientation. Side Bracket Mount (IntelliTouch and No Touch models only) Threaded holes are provided on the sides of the monitor for mounting using the provided brackets.
Flush Bracket Mount (iTouch and Projected Capacitive models only) Threaded holes are provided on the back of the monitor for mounting using the provided brackets.
Rear VESA Mount (All models) A four-hole 200x100mm mounting pattern for M4 screws is provided on the rear of the monitor. The VESA FDMI-compliant counting is coded: VESA MIS-D, 200mm x 100mm.
Chapter 4: Operation Power The touchmonitor ships in an ON state. To turn the touchmonitor on or off, press the touchmonitor power button on the OSD controller once. The Power Status LED on the OSD controller functions according to the following table: Touchmonitor status LED status OFF OFF SLEEP PULSING ON ON The system consumes low power when in SLEEP and OFF modes. For detailed power consumption specifications, refer to technical specifications on the Elo website http://www.elotouch.
IntelliTouch/iTouch Plus touchscreen technology. To use multiple IntelliTouch/iTouch Plus monitors, plug in monitors to calibrate, double-click on the EloConfig desktop shortcut to run Elo Touchscreen Configuration screen. Click on “Calibrate Touch Screens…” to calibrate multiple monitors.
Tap monitor screen to identify monitor’s identity as shown below. Identity of the monitor will display. Click on “OK” to proceed to calibration.
Calibrate touch as targets appear on corners of the screen. Follow instructions on screen. Test touch/drag performance to verify calibration accuracy, “Accept” or “Retry” to redo calibration process. Run touch calibration on each monitor that is plugged in.
Projected Capacitive Touch Technology When connected to Windows 7 computers, the touchmonitor can report 2 simultaneous touches. When connected to Windows XP computers, the touchmonitor reports single touches. No additional drivers are required for this technology to work, it uses Windows HID drivers. No calibration is required for this technology. Gesture Support The IntelliTouch/iTouch Plus and Projected Capacitive touch technologies enable several gestures that support single and multiple touches.
On-Screen Display (OSD) Four OSD buttons are located on a wired control box. These can be used to adjust various display parameters.
Switches the scaling method between Full Scaling and Maintain Aspect Ratio. Default: Full Scaling Aspect Ratio Full Scaling – scales the X- and Y-dimensions of the input video (up or down as needed) to the display’s native resolution.
OSD and Power Lockouts Press and hold the “Menu” and “ ” buttons for two seconds to enable/disable the OSD Locking feature. When the OSD Locking is enabled, pressing any of the “Menu”, “ ”, “ ”, or “Select” keys will have no effect on the system. Press and hold the “Menu” and “ ” buttons for two seconds to enable/disable the Power Locking feature. When the Power Locking is enabled, pressing the power switch will have no effect on the system.
Chapter 5: Technical Support If you are experiencing trouble with your touchmonitor, refer to the following suggestions. If the problem persists, please contact your local dealer or contact Elo Touch Solutions Customer Service. Worldwide technical support phone numbers are available on the last page of this use manual.
Technical Assistance Visit www.elotouch.com/products for technical specifications for this device Visit www.elotouch.com/go/websupport for online self-help. Visit www.elotouch.com/go/contactsupport for technical support. See this user manual’s last page for worldwide technical support phone numbers.
Chapter 6: Safety & Maintenance Safety To avoid risk of electric shock, follow all safety notices and do not disassemble the touchmonitor. They are not user-serviceable. Ensure that your installation is equipped to maintain the specified environmental conditions listed in the Technical Specifications chapter. Care and Handling The following tips will help keep your touchmonitor functioning at an optimal level: • Disconnect the AC power cable before cleaning.
Waste Electrical & Electronic Equipment Directive (WEEE) This product should not be disposed of with household waste. It should be deposited at a facility that enables recovery and recycling.
Chapter 7: Regulatory Information I. Electrical Safety Information: Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. There are no operator serviceable parts inside this equipment.
as required by EMC Directive 2004/108/EC as indicated in European Standard EN 55022 Class B and the Low Voltage Directive 2006/95/EC as indicated in European Standard EN 60950. General Information to all Users: This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to this manual the equipment may cause interference with radio and television communications.
III. Agency Certifications The following certifications and marks have been issued or declared for this monitor: Australia C-Tick Europe CE Mexico CoC Canada CUL, IC Japan VCCI Taiwan BSMI China CCC Korea KCC, e-Standby United States FCC, UL IV. China RoHS In accordance to Chinese law (Administration on the Control of Pollution Caused by Electronic Information Products), the section below lists out the name and amount of the toxic and/or hazardous materials that this product may contain.
Explanation of Markings (1). In accordance with the SJ/T11364-2006 requirement, the electronic information products are marked with the following pollution control logo. The Environment-Friendly Use Period for this product is 10 years. The product will not leak or mutate under normal operating conditions listed below, so that the use of this electronic information product will not result in any severe environmental pollution, any bodily injury, or damage to any assets.
Operating Conditions: Temperature: 0°C - 40°C Humidity: 20% to 80% (non-condensing) Altitude: 0 to 3,048m Storage Conditions: Temperature: -20°C - 60°C Humidity: 10% to 95% (non-condensing) Altitude: 0 to 12,192m User Manual: 2440L SW602154 Rev A, Page 32 of 34
Chapter 8: Warranty Information See http://www.elotouch.com/Support/warranty.asp for more information.
Check out Our Website! www.elotouch.com Get the latest... • Product Information • Specifications • Upcoming events • Press releases • Software drivers Getting in Touch with us To find out more about the extensive range of Elo touch solutions, visit our website at www.elotouch.com, or simply call the office nearest you: North America Elo Touch Solutions 1033 McCarthy Blvd Milpitas, CA 95035 Tel 800-ELO-TOUCH Tel +1-408-597-8000 Fax +1-408-597-8050 customerservice@elotouch.
