M-Series Touchcomputer User Guide M-Series LCD Multi-function Touchcomputer [19” model shown with optional accessories]
Elo Touch Solutions M-Series Touchcomputer for Healthcare Applications User Guide Multi-function Touchcomputer Revision A SW200069 1-800-ELOTOUCH (1-800-356-8682) www.elotouch.
Copyright © 2012 Elo Touch Solutions Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions. Disclaimer The information in this document is subject to change without notice. Elo Touch Solutions Inc.
Warnings and Cautions Warning • Danger - Explosion hazard. Do not use in the presence of flammable • • • • • • • anesthetics, and other flammable materials. To prevent fire or shock hazards, do not immerse the unit in water or expose it to rain or moisture. Do not use the unit with an extension cord receptacle or other outlets unless the prongs of the power cord can be fully inserted. RISK OF ELECTRICAL SHOCK - DO NOT OPEN.
Caution Power cord is used as a disconnection device. To de-energize equipment, disconnect the power cord. This unit must follow the national requirement and local state laws to dispose unit. Before connecting the cables to your Elo touchcomputer, make sure all components are powered OFF. Only approved components complying with IEC 60601-1 series can be connected to 15MX/19MX Touchcomputer for Healthcare Applications in Patient Environment.
Explanation of Symbols: ! • This symbol alerts the user to important information concerning the operation and maintenance of this unit, which should be read carefully to avoid problems. • This symbol means DC Current. • This symbol means ON/OFF stand-by switch. • Consult instructions for use. Medical and Healthcare Application Disclaimer: It is the sole responsibility of any person intending to commercialize, market or use any of Elo Touch Solutions, Inc.
Classification With respect to electrical shock, fire in accordance with ANSI/AAMI ES60601-1 and CAN/CSA- C22.2 No. 60601-1 E354528 07EG This touchcomputer is a Class I (GROUNDED) DEVICE. This touchcomputer is classified NO APPLIED PARTS EQUIPMENT. Protection against harmful ingress of water: INGRESS PROTECTION (IP21) This touchcomputer shall be classified as ORDINARY EQUIPMENT, not intended or evaluated for use in the presence of flammable anesthetic mixture with air, oxygen, or nitrous oxide.
European Standards and Classifications Standards: EN 60601-1-2: 2007 The EMC limits and test methods are referred to the following standards: Emission: CISPR 11: 2009+A1:2010 EN55011: 2009+A1: 2010 (Group 1, Class A) IEC 61000-3-2: 2005+A1:2008+A2:2009 IEC 61000-3-3; 2008 Immunity IEC 61000-4-2: 2008 IEC 61000-4-3: 2006+A1:2007+A2:2010 IEC 61000-4-4: 2011 IEC 61000-4-5: 2005 IEC 61000-4-6: 2008 IEC 61000-4-8: 2009 IEC 61000-4-11: 2004 M-Series Touchcomputer User Guide viii
Guidance and manufacturer’s declaration-electromagnetic immunity for all EQUIPMENT AND SYSTEMS Guidance and manufacturer’s declaration-electromagnetic emissions The 15MX/19MX Touchcomputer for Healthcare Applications is intended for use in the electromagnetic environment specified below. The customer or the user of the 15MX/19MX Touchcomputer for Healthcare Applications should assure that it is used in such an environment.
Guidance and manufacturer’s declaration-electromagnetic immunity for all EQUIPMENT AND SYSTEMS Guidance and manufacturer’s declaration-electromagnetic immunity The 15MX/19MX Touchcomputer for Healthcare Applications is intended for use in the electromagnetic environment specified below. The customer, or the user of the 15MX/19MX Touchcomputer for Healthcare Applications, should assure that it is used in such an environment.
Guidance and manufacturer’s declaration-electromagnetic immunity for all EQUIPMENT AND SYSTEMS that are not LIFE-SUPPORTING Guidance and manufacturer’s declaration-electromagnetic immunity The 15MX/19MX Touchcomputer for Healthcare Applications is intended for use in the electromagnetic environment specified below. The user of the 15MX/19MX Touchcomputer for Healthcare Applications should assure that it is used in such an environment.
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. 3. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
Recommended separation distances between portable and mobile RF communications equipment and the 15MX/19MX Touchcomputer for Healthcare Applications for all EQUIPTMENT AND SYSTEMS that are not LIFE-SUPPORTING The 15MX/19MX Touchcomputer for Healthcare Applications is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
Table of Contents Chapter 1: Setup...................................................................................... 1 Unpacking Your Touchcomputer ....................................................................................................1 Touchcomputer Operating System ..................................................................................................2 Accessing the Hard Disk........................................................................................................
Technical Assistance......................................................................................................................18 Regulatory Information............................................................................19 Warranty ...................................................................................................27 Index..........................................................................................................
C H A P T E R 1 SETUP This chapter discusses how to set up and test your touchcomputer. For information on peripheral options, refer to Chapter 3, “Options and Upgrades.
Touchcomputer Operating System The touchcomputer may be delivered without an operating system. An operating system must be installed before many of the features of the touchcomputer can be used. The hardware used on the touchcomputer is compatible with many common operating systems. Accessing the Hard Disk The hard disk is factory installed and located under the hard disk cover on the back of the unit.
Calibrating the Touchscreen The touchscreen is pre-calibrated for accurate touch response. If for any reason the touchscreen needs to be recalibrated, right-click the Elo icon in the Taskbar and then click “Properties.” The following window opens. NOTE: Calibration is not applicable on projective capacitive touchscreen models. NOTE: OS and touchscreen drivers must be installed for Elo icon to appear in the Taskbar Click the Align button. This launches the calibration program.
Securing the M-Series AIO to a Mounting Bracket Use the four pre-tapped holes to secure the touchcomputer to the mounting bracket. The holes are designed to work with ISO metric M4 screws. Mounting screws are not included. Select the length screw that will provide adequate thread engagement to provide a reliable connection to the mounting bracket. The correct length screw for your application should be commonly available at a hardware store. Refer to the figure below for the location of the 4 holes.
C H A P T E R 2 OPERATION This chapter describes the user button functions and I/O panel. All adjustments made to the user buttons are reset upon a power cycle to the touchcomputer.
User Buttons User buttons are capacitive buttons. Use of finger or appropriate stylus is required for proper function. Power Button The power button function is different depending on the state of the touchcomputer.
Screen Brightness Function Touch the screen brightness icon and use the +/- function adjustment icons to adjust the intensity. Current setting is displayed in-between +/- icons. Audio Volume Function Touch the audio volume icon and use the +/- function adjustment icons to adjust the intensity. Current setting is displayed in-between +/- icons. Function Adjustment The function adjustment icons are illuminated when enabled.
Using the Input/Output Panel To access the input/output (I/O) ports, remove the cable cover on left side of the back of the unit. Install the I/O cables in the respective ports and use plastic cable ties to fasten the cables to the cable restraints shown below. Below are the I/O descriptions and location of the cable restraints: Note: As a safety precaution, always leave the cable cover attached when the system is powered on.
C H A P T E R 3 OPTIONS AND UPGRADES Peripherals and Accessories The following peripherals and accessories are available for the M-Series touchcomptuers.
Magnetic Stripe Reader (MSR) A magnetic stripe reader (MSR) is an optional M-Series touchcomputer peripheral. Software application and drivers can be found on the web at: www.elotouch.com The MSR is a USB 2.0 device that reads all three data stripes on standard credit cards or driver’s licenses conforming to ISO/ANSI standards. The MSR has foreign language capability.
Wireless Card A wireless adapter is a standard peripheral in the M-Series touchcomputer. Typical specifications for the wireless card are: • Mini PCI-E module • IEEE 802.11 a/b/g/n compliant Solid State Drive A solid state drive can be used to replace the original hard disk drive. This addition provides additional performance and is more mechanically reliable in harsh environments. Access to the original hard disk drive is through the right side cover on the back of the M-Series touchcomputer.
Auto Frame Rate 5fps max @ 2.0 megapixels (1600x1200); 24fps max @ VGA mode (640x480) Field Of View (FOV) 66° Focus Range 40cm ~ Infinity Barcode Scanner A 2D area array barcode scanner is an optional M-Series touchcomputer peripheral. The barcode scanner has integrated illumination and is compatible with many barcode symbologies. The barcode scanner supports a typical reading range shown in the table below. Symbology / X-Dim Typical Range* 100% U.P.C. 46 mm to 419 mm (1.8˝ to 16.
RFID Reader An RFID reader is an optional M-Series touchcomputer peripheral. If installed, the RFID reader is capable of reading tags presented within a few centimeters of the symbol shown below on the front of M-Series touchcomputer.
USB Handset A USB Handset is an optional M-Series touchcomputer peripheral. Included in the kit is a bracket and handset cradle that is required for correct function. Part number: E709063 TV Tuner A USB TV Tuner kit is available as an optional accessory. There are three options available. All options include a 1.2 meter USB extension cable that can be plugged into the I/O area under the cable cover so that the TV Tuner can be installed outside of the M-Series device.
AC Cable A country specific AC cable can be used to replace the original AC Cable. There are two options. • UK-HK 1.8 Meter AC cable Part number: E010063 • Japan 1.
C H A P T E R 4 SAFETY AND MAINTENANCE Safety Important information regarding the proper setup and maintenance of your touchcomputer: • To reduce the risk of electric shock, follow all safety notices and never open the touchcomputer case. • Turn off the product before cleaning (refer to “Care and Handling” on page 17 for proper cleaning methods). • Your touchcomputer is equipped with a 3-wire, grounding power cord. The power cord plug only fits into a grounded outlet.
Care and Handling The following tips help keep your touchcomputer functioning at the optimal level. Power down the unit and disconnect from the electrical mains prior to engaging in any cleaning activities. Take care to ensure no leakage of solution into the system. IF ANY FLUID INGRESS INTO THE UNIT DURING CLEANING IS SUSPECTED, DO NOT POWER ON THE UNIT. Call the manufacturer at the contact numbers listed below to have your unit inspected by a qualified technician prior to powering on.
C H A P T E R 5 TECHNICAL SUPPORT TECHNICAL SPECIFICATIONS Touchcomputer Specifications For touch computer specifications go to www.elotouch.com Not all operating systems or options are supported in all regions. Please contact your local Elo TouchSystems representative for details. NOTE: Technical Assistance There are three methods to obtain contact information for technical assistance on the touchcomputer: • The web • The phone Using the Web For technical support, go to www.elotouch.
REGULATORY INFORMATION I. Electrical Safety Information A) Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified herein may result in improper operation, damage to the equipment, invalidation of warranty, or a fire hazard if the requirements are not followed. B) There are no operator-serviceable parts inside this equipment.
and interconnecting cabling provided with the equipment.
source of high RF emission levels.) v) Plug the digital device into only a grounded outlet receptacle. Do not use AC adapter plugs. (Removing or cutting the line cord ground may increase RF emission levels and may also present a lethal shock hazard to the user.) If you need additional help, consult your dealer, manufacturer, or an experienced radio or television technician. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules.
Exposure to radio frequency radiation The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
EN 301 489-17 V2.1.1 2009 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.
citiem ar to saistītajiem noteikumiem. Šiuo Elo Touch Solutions, Inc. deklaruoja, kad šis 15MX/19MX Touchcomputer atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hierbij verklaart Elo Touch Solutions, Inc. dat het toestel 15MX/19MX Nederlands Touchcomputer in overeenstemming is met de essentiële eisen en de [Dutch] andere relevante bepalingen van richtlijn 1999/5/EG. Malti Hawnhekk, Elo Touch Solutions, Inc.
IV. Ingress Protection The 15MX/19MX Touchcomputer is designed to have an ingress protection rating of IP21 over the range of angles shown in the diagram below.
WARRANTY Except as otherwise stated herein or in an order acknowledgment delivered to Buyer, Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship. With the exception of the negotiated warranty periods; the warranty for the touchcomputer and components of the product is 3 years. Seller makes no warranty regarding the model life of components. Seller’s suppliers may at any time and from time to time make changes in the components delivered as Products or components.
THESE REMEDIES SHALL BE THE BUYER’S EXCLUSIVE REMEDIES FOR BREACH OF WARRANTY. EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, SELLER GRANTS NO OTHER WARRANTIES, EXPRESS OR IMPLIED BY STATUTE OR OTHERWISE, REGARDING THE PRODUCTS, THEIR FITNESS FOR ANY PURPOSE, THEIR QUALITY, THEIR MERCHANTABILITY, THEIR NONINFRINGEMENT, OR OTHERWISE. NO EMPLOYEE OF SELLER OR ANY OTHER PARTY IS AUTHORIZED TO MAKE ANY WARRANTY FOR THE GOODS OTHER THAN THE WARRANTY SET FORTH HEREIN.
INDEX address, Elo TouchSystems, 36 base, securing, 4 box contents, 1 cables included, 1 calibration, 2, 3 certifications, 32 contact information, 24 controls, location diagram, 5 customer support, 24 email, Elo TouchSystems, 36 enabling or disabling power, 8 input/output (I/O) panel accessing, 9 specifications magnetic stripe reader, 11 wireless card, 12 technical support, 20 touchscreen calibrating, 2, 3 care and handling, 18 upgrades, adding, 10 warranty, 33 website, Elo TouchSystems, 24, 36 wireless ca
www.elotouch.com Get the latest... • Product information • Specifications • News on upcoming events • Press release • Software drivers • Touchcomputer Newsletter Getting in Touch with Elo To find out more about the extensive range of Elo touch solutions, visit www.elotouch.com or simply call the office nearest you: Europe Asia-Pacific Elo Touch Solutions Inc. Elo Touch Solutions Inc. Sun Hamada Bldg.
