USER MANUAL Elo Touch Solutions 2740L Touchmonitors SW602096 Rev A
Copyright © 2013 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc. Disclaimer The information in this document is subject to change without notice. Elo Touch Solutions, Inc.
Table of Contents Chapter 1: Introduction ...........................................................................................4 Chapter 2: Installation .............................................................................................5 Chapter 3: Mounting ..............................................................................................10 Chapter 4: Operation .............................................................................................
Chapter 1: Introduction Product Description Your new touchmonitor combines the reliable performance of Elo Touch Solutions touch products with the latest developments in touch technology and display design. This combination of features creates a natural flow of information between a user and the touchmonitor. This widescreen touchmonitor incorporates a 24-bit color, active matrix thin-film-transistor LCD panel to provide high quality display performance.
Chapter 2: Installation Unpacking the Touchmonitor Open the carton and verify that the following items are present: • Touchmonitor with protective sheet for its face • User Manuals CD • Japanese language regulatory information pamphlet • Quick Install Guide • VGA cable • DVI cable • USB cable (not available for ET2740L-0NXX models) • Mounting brackets • OSD remote User Manual: 2740L SW602096 Rev A, Page 5 of 27
Connector Panel & Interfaces Touchmonitor Connections 1. Connect the DVI or VGA video cables between the monitor’s DVI/VGA input connectors and your DVI/VGA video source. Tighten the video cable’s screws for best performance. 2. Connect the USB touch cable between the monitor’s USB connector and your PC’s USB port. (Not applicable for ET2740L-0NXX models) 3. Connect a 12VDC power supply to the monitor’s input power jack. 4.
Installing the Touch Technology Software Drivers Some software installation is required for your touchmonitor to work with your computer. The drivers are available on the Elo Touch Solutions website. Visit www.elotouch.
For Windows XP installations, install the “USB Touchscreen Drivers” when prompted: User Manual: 2740L SW602096 Rev A, Page 8 of 27
For Windows 7 installations, check the “Install driver” box under “Elo USB Interfaces – Other Touchscreens” After accepting the end-user license agreement, the drivers will finish installing. Reboot your computer after the install is complete.
Chapter 3: Mounting General Mounting Information The OSD text can be rotated through the OSD menu to better suit your mounting orientation. Side Bracket Mount Threaded holes are provided on the sides of the monitor for mounting using the provided brackets.
A four-hole 200x100mm mounting pattern for M4 screws is provided on the rear of the monitor. The VESA FDMI-compliant counting is coded: VESA MIS-E, C.
Chapter 4: Operation Power The touchmonitor ships in an ON state. To turn the touchmonitor on or off, press the touchmonitor power button on the OSD controller once. The Power Status LED on the OSD controller functions according to the following table: TouchMonitor/Computer Module status LED status OFF OFF SLEEP PULSING ON ON The system consumes low power when in SLEEP and OFF modes. For detailed power consumption specifications, refer to technical specifications on the Elo website http://www.elotouch.
The IntelliTouch Plus driver will only support multiple monitor if they are all using the IntelliTouch Plus touchscreen technology. To use multiple IntelliTouch Plus monitors, double click on the EloConfig desktop shortcut to open up the Elo Touchscreen Configuration screen. Select “Match Touch to Display…” to calibrate multiple monitors.
Gesture Support The IntelliTouch Plus touch technology enables several gestures that support single and multiple touches. Refer to the Microsoft Website http://msdn.microsoft.com/en-us/library/dd940543 on the various gestures that are supported in Windows 7. Video A display’s native resolution is its width and height measured in number of pixels.
The buttons and their functionality are: Button Menu Function when OSD is not displayed: Display OSD main menu Display OSD Brightness submenu Display OSD Contrast submenu Select Auto Adjust Function when OSD is displayed: Return to previous OSD menu Increase value of selected parameter / select previous menu item Decrease value of selected parameter / select next menu item Select parameter for adjustment / select submenu to enter Using the OSD buttons controls an on-screen graphical user interface whic
Switches the scaling method between Full Scaling and Maintain Aspect Ratio. Default: Full Scaling Full Scaling – scales the X- and Y-dimensions of the input video (up or down as needed) to the display’s native resolution.
OSD and Power Lockouts Press and hold the “Menu” and “Up” buttons for two seconds to enable/disable the OSD Locking feature. When the OSD Locking is enabled, pressing any of the Menu, Up, Down, or Select keys will have no effect on the system. Press and hold the “Menu” and “Down” buttons for two seconds to enable/disable the Power Locking feature. When the Power Locking is enabled, pressing the power switch will have no effect on the system.
Chapter 5: Technical Support If you are experiencing trouble with your touchmonitor, refer to the following suggestions. If the problem persists, please contact your local dealer or contact Elo Touch Solutions Customer Service. Worldwide technical support phone numbers are available on the last page of this use manual.
Technical Assistance Visit www.elotouch.com/products for technical specifications for this device Visit www.elotouch.com/go/websupport for online self-help. Visit www.elotouch.com/go/contactsupport for technical support. See this user manual’s last page for worldwide technical support phone numbers.
Chapter 6: Safety & Maintenance Safety To avoid risk of electric shock, follow all safety notices and do not disassemble the touchmonitor. They are not user-serviceable. Ensure that your installation is equipped to maintain the specified environmental conditions listed in the Technical Specifications chapter. Care and Handling The following tips will help keep your touchmonitor functioning at an optimal level: Disconnect the AC power cable before cleaning.
Waste Electrical & Electronic Equipment Directive (WEEE) This product should not be disposed of with household waste. It should be deposited at a facility that enables recovery and recycling.
Chapter 7: Regulatory Information I. Electrical Safety Information: Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. There are no operator serviceable parts inside this equipment.
as required by EMC Directive 2004/108/EC as indicated in European Standard EN 55022 Class B and the Low Voltage Directive 2006/95/EC as indicated in European Standard EN 60950. General Information to all Users: This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to this manual the equipment may cause interference with radio and television communications.
III. Agency Certifications The following certifications and marks have been issued or declared for this monitor: Argentina S-Mark Japan VCCI Taiwan BSMI Australia C-Tick Canada CUL, IC Korea KCC, e-Standby United States FCC, UL China CCC Mexico CoC Europe CE IV.
Explanation of Markings (1). In accordance with the SJ/T11364-2006 requirement, the electronic information products are marked with the following pollution control logo. The Environment-Friendly Use Period for this product is 10 years. The product will not leak or mutate under normal operating conditions listed below, so that the use of this electronic information product will not result in any severe environmental pollution, any bodily injury, or damage to any assets.
Chapter 8: Warranty Information Except as otherwise stated herein, or in an order acknowledgment delivered to Buyer, Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship. The warranty for the touchmonitors and their components is three years. Seller makes no warranty regarding the model life of components. Seller’s suppliers may at any time and from time to time make changes in the components delivered as Products or components.
Check out Our Website! www.elotouch.com Get the latest... • Product Information • Specifications • Upcoming events • Press releases • Software drivers Getting in Touch with us To find out more about the extensive range of Elo touch solutions, visit our website at www.elotouch.com, or simply call the office nearest you: North America Elo Touch Solutions 1033 McCarthy Blvd Milpitas, CA 95035 Tel 800-ELO-TOUCH Tel 1-408-597-8000 Fax 1-408-597-8001 customerservice@elotouch.
