USER MANUAL Elo Touch Solutions 2401LM Touchmonitor SW200127 Rev A
Copyright © 2013 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc. Disclaimer The information in this document is subject to change without notice. Elo Touch Solutions, Inc.
Warnings and Cautions Warning • Danger - Explosion hazard. Do not use in the presence of flammable anesthetics, and other flammable materials. • To prevent fire or shock hazards, do not immerse the unit in water or expose it to rain or moisture. • Do not use the unit with an extension cord receptacle or other outlets unless the prongs of the power cord can be fully inserted. • RISK OF ELECTRICAL SHOCK - DO NOT OPEN.
Caution Power cord is used as a disconnection device. To de-energize equipment, disconnect the power cord. This unit must follow the national requirement and local state laws to dispose unit. Before connecting the cables to your Elo Touchmonitor, make sure all components are powered OFF. Only approved components complying with IEC60601-1 series can be connected to 2401LM touch monitor for Healthcare Applications in Patient Environment.
Classification With respect to electrical shock, fire in accordance with ANSI/AAMI ES60601-1:2005 and CAN/CSA C22.2 No. 60601-1-08 This Touchmonitor is a Class I (GROUNDED) DEVICE. These Touchmonitors are classified NO APPLIED PARTS EQUIPMENT. Protection against harmful ingress of water: INGRESS PROTECTION (IPX1) This Touchmonitor shall be classified as ORDINARY EQUIPMENT, not intended or evaluated for use in the presence of flammable anesthetic mixture with air, oxygen, or nitrous oxide.
European Standards and Classifications Standards: EN 60601-1-2: 2007 The EMC limits and test methods are referred to the following standards: Emission: Immunity CISPR11:2009+A1:2010 ED. 5.1(Grp I, Class B) AS/NZS CISPR 11: 2011, Grp. 1, Class B IEC61000-4-2:2008 ED.2.0 IEC61000-4-3:2006+A1:2007 +A2:2010ED.3.2 IEC 61000-4-4: 2012 ED.3.0 EN 61000-3-2: 2006 +A1: 2008+A2: 2009, Class D IEC 61000-4-5: 2005 ED.2.0 IEC 61000-3-3: 2008 IEC 610004-6: 2008 ED.3.0 IEC 61000-4-8: 2009 ED.2.
Guidance and manufacturer’s declaration-electromagnetic immunity for all EQUIPMENT AND SYSTEMS Guidance and manufacturer’s declaration-electromagnetic emissions The 2401LM Touchmonitor for Healthcare Applications is intended for use in the electromagnetic environment specified below. The customer or the user of the 2401LM Touchmonitor for Healthcare Applications should assure that it is used in such an environment.
Guidance and manufacturer’s declaration-electromagnetic immunity for all EQUIPMENT AND SYSTEMS Guidance and manufacturer’s declaration-electromagnetic immunity The 2401LM Touchmonitor for Healthcare Applications is intended for use in the electromagnetic environment specified below. The customer, or the user of the 2401LM Touchmonitor for Healthcare Applications, should assure that it is used in such an environment.
Guidance and manufacturer’s declaration-electromagnetic immunity for all EQUIPMENT AND SYSTEMS that are not LIFE-SUPPORTING Guidance and manufacturer’s declaration-electromagnetic immunity The 2401LM Touchmonitor for Healthcare Applications is intended for use in the electromagnetic environment specified below. The user of the 2401LM Touchmonitor for Healthcare Applications should assure that it is used in such an environment.
Recommended separation distances between portable and mobile RF communications equipment and the 2401LM Touchmonitor for Healthcare Applications for all EQUIPTMENT AND SYSTEMS that are not LIFE-SUPPORTING The 2401LM Touchmonitor for Healthcare Applications is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
Table of Contents Chapter 1: Introduction................................................................................ 12 Chapter 2: Installation.................................................................................. 13 Chapter 3: Mounting .................................................................................... 17 Chapter 4: Operation.................................................................................... 19 Chapter 5: Technical Support ................................
Chapter 1: Introduction Product Description Your new touch monitor combines Elo Touch Solutions’ reliable performance with the latest developments in touch technology and display design. This combination of features creates a natural flow of information between a user and the Touchmonitor. This Touchmonitor incorporates a 8-bit color, active matrix thin-film-transistor LCD panel to provide high quality display performance. Its Full HD resolution of 1920x1080 is suitable for displaying graphics and images.
Chapter 2: Installation Unpacking the Touch monitor Open the carton and verify the following items are present: • Touchmonitor with protective sheet for its face • Elo TouchTools CD • Quick Install Guide • DVI cable • VGA cable • USB cable • AC-DC power adapter • AC Power Cable • Audio Cable • Serial Cable Connector Panel & Interfaces Remove the cable cover on the back of the unit to access the Touchmonitor’s connector panel. © 2013 Elo Touch Solutions, Inc. All rights reserved.
Touchmonitor Connections 1. Connect the DVI or VGA video cables between the monitor’s DVI/VGA input connectors and your DVI/VGA video source, respectively. Tighten the video cable’s screws for best performance. 2. Connect the USB touch cable between the monitor’s USB connector and your PC’s USB port. 3. Connect the audio cable between the monitor’s Audio In jack and your audio source. 4. Select the correct power cable for your region.
Installing the Touch Technology Software Drivers Some software installation is required for your Touchmonitor to work with your computer. The drivers for the Windows 7, XP, Vista, WePOS, and 32-bit Server 2003 operating systems are provided with your Touchmonitor on a CD. Visit the Elo Touch Solutions website www.elotouch.
For Windows 7 installations, check the “Install driver” box under “Elo USB Interfaces – Other Touchscreens” After accepting the end-user license agreement, the drivers will finish installing. Reboot your computer after the install is complete. © 2013 Elo Touch Solutions, Inc. All rights reserved.
Chapter 3: Mounting General Mounting Information The OSD text can be rotated through the OSD menu to better suit your mounting orientation. The holes located on the top and bottom of the Touchmonitor case are for ventilation. Do not block, cover, or insert anything inside the ventilation slots. Rear VESA Mount A four-hole 100x100mm mounting pattern for M4 screws is provided on the rear of the monitor. Remove the stand using a Phillips screwdriver to access this mounting interface.
Stand Mounting Threaded through-holes are provided on the bottom of the stand base for mounting or securing. VESA Mounting Options The following companies provide VESA mounting devices compatible with your touch monitor : GCX 800-228-2555 707-773-1100 www.gcx.com Ergotron 800-888-8458 651-681-7600 www.ergotron.com Innovative Office Products 800-524-2744 610-253-9554 www.innov-office-prod.com MRI 800-688-2414 www.mediarecovery.com © 2013 Elo Touch Solutions, Inc. All rights reserved.
Chapter 4: Operation Power To turn the Touchmonitor on or off, press the Touchmonitor power button once. The Power Status LED on the bottom of the Touchmonitor functions according to the following table: Touchmonitor/Computer Module status OFF SLEEP ON LED status OFF ORANGE GREEN The system consumes low power when in SLEEP and OFF modes. For detailed power consumption specifications, refer to technical specifications on the Elo website http://www.elotouch.
(for example images containing small-font text). Your Touchmonitor will likely not require video adjustments. However, for analog VGA video, variations in video graphic card outputs may require user adjustments through the OSD to optimize the quality of the Touchmonitor’s displayed image. These adjustments are “remembered” by the Touchmonitor.
Selects the display’s color temperature. The available color temperatures are 9300K, 6500K, 5500K, 7500K, and User Defined. If the User Defined option is selected, the Color user can change the color temperature by changing individual R, G, and B gains on a Temperature scale from 0 to 100. Default: User Defined with R, G, and B all set to 100. Adjusts the volume of the internal speakers output. Volume Adjusts sharpness of the displayed images.
OSD and Power Lockouts Press and hold the “Menu” and “Up” buttons for two seconds to enable/disable the OSD Locking feature. When the OSD Locking is enabled, pressing any of the Menu, Up, Down, or Select keys will have no effect on the system. Press and hold the “Menu” and “Down” buttons for two seconds to enable/disable the Power Locking feature. When the Power Locking is enabled, pressing the power switch will have no effect on the system.
Chapter 5: Technical Support If you are experiencing trouble with your Touchmonitor, refer to the following suggestions. If the problem persists, please contact your local dealer or contact Elo Touch Solutions Customer Service. Solutions to Common Problems Problem Suggested Troubleshooting Check that the AC power cable is properly The Touchmonitor does not respond when connected. turning on the system. Verify the AC power source is functioning. Use the OSD to increase the brightness.
Chapter 6: Safety & Maintenance Safety To avoid risk of electric shock, follow all safety notices and do not disassemble the Touchmonitor. They are not user-serviceable. The slots located on the sides and top of the Touchmonitor case are for ventilation. Do not block or insert anything inside the ventilation slots. The Touchmonitor ships with a 3-wire, grounding power cord. The power cord plug only fits into a grounded outlet.
Waste Electrical & Electronic Equipment Directive (WEEE) This product should not be disposed of with household waste. It should be deposited at a facility that enables recovery and recycling. © 2013 Elo Touch Solutions, Inc. All rights reserved.
Chapter 7: Regulatory Information I. Electrical Safety Information: Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. There are no operator serviceable parts inside this equipment.
v) Disconnect and remove any I/O cables that the digital device does not use.(Un-terminated I/O cables are a potential source of high RF emission levels.) vi) Plug the digital device into only a grounded outlet receptacle. Do not use AC adapter plugs. (Removing or cutting the line cord ground may increase RF emission levels and may also present a lethal shock hazard to the user.) If you need additional help, consult your dealer, manufacturer, or an experienced radio or television technician. III.
IV. China RoHS In accordance to Chinese law (Administration on the Control of Pollution Caused by Electronic Information Products), the section below lists out the name and amount of the toxic and/or hazardous materials that this product may contain.
Input: 100-240VAC, 50-60Hz Output: 12VDC, minimum 3A, LPS VI. Monitor Specifications Electrical Ratings: Input: 12VDC, 3A Operating Conditions: Temperature: 0°C - 35°C Humidity: 20% to 80% (non-condensing) Altitude: 0 to 3,048m Storage Conditions: Temperature: -20°C - 50°C Humidity: 10% to 90% (non-condensing) Altitude: 0 to 12,192m © 2013 Elo Touch Solutions, Inc. All rights reserved.
Chapter 8: Warranty Information Except as otherwise stated herein, or in an order acknowledgment delivered to Buyer, Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship. The warranty for the Touchmonitors and their components is three years. Seller makes no warranty regarding the model life of components. Seller’s suppliers may at any time and from time to time make changes in the components delivered as Products or components.
Index Agency Certifications, 27 Altitude, 5 Available Adjustment Auto Adjust, 21 Brightness, 20 Clock, 21 Color Temperature, 21 Contrast, 20 H-position, 20, 21 Input Video, 21 OSD Language, 21 OSD Timeout, 21 Phase, 21 Recall Defaults, 20 Sharpness, 21 Volume, 21 V-position, 20, 21 Lockouts, 22 OSD and Power, 22 Mode of Operation, 5 Monitor Specifications, 29 Mounting Information, 17 native resolution, 19 online self-help, 23 On-Screen Display, 20 Operating, 5 OSD, 20 OSD buttons, 20 Out Of Range, 23 Power
Check out our website www.elotouch.com Get the latest... • Product Information • Specifications • Upcoming events • Press releases • Software drivers Getting in Touch with Us To find out more about the extensive range of Elo touch solutions, visit our website at www.elotouch.com, or simply call the office nearest you: North America Elo Touch Solutions 1033 McCarthy Blvd Milpitas, CA 95035 Tel 800-ELO-TOUCH Tel + 1 408 597 8000 Fax +1 408 597 8050 customerservice@elotouch.
