User Manual Elo TouchSystems 1940L Touchmonitor User Manual – 1940L SW601787 Rev A Page 1 of 26
Copyright © 2012 Tyco Electronics Corporation, TE Connectivity Ltd. Company. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Tyco Electronics. Disclaimer The information in this document is subject to change without notice.
Table of Contents Chapter 1 - Introduction ........................................................................... 4 Chapter 2 – Installation ............................................................................. 5 Chapter 3 – Mounting ................................................................................ 11 Chapter 4 – Operation ............................................................................... 14 Chapter 5 – Technical Support ..............................................
Chapter 1 - Introduction Product Description Your new touchmonitor combines Elo TouchSystems reliable product performance with the latest developments in touch technology and display design. This combination of features creates a natural flow of information between a user and the touchmonitor. This widescreen touchmonitor incorporates a 24-bit color, active matrix thin-film-transistor LCD panel to provide high quality display performance.
Chapter 2 –Installation Unpacking the Touchmonitor Open the carton and verify the following items are present: Touchmonitor with protective sheet for its face Elo TouchTools CD & User Manuals CD Quick Install Guide Japanese language regulatory information pamphlet DVI cable (depending on model purchased) VGA cable USB cable REMOTE OSD controller Connector Panel & Interfaces Touchmonitor Connections 1. 2. 3. 4.
Installing the Touch Technology Software Drivers Some software installation is required for your touchmonitor to work with your computer. The drivers for the Windows 7, XP, Vista, WePOS, and 32-bit Server 2003 and 2008 operating systems are provided with your touchmonitor on a CD. Visit the Elo TouchSystems website www.elotouch.
For Windows XP, Vista, Server 2003, Server 2008, and WEPOS installations, install the “USB Touchscreen Drivers” when prompted: For Windows 7 installations, check the “Install driver” box under “Elo USB Interfaces – Other Touchscreens” After accepting the end-user license agreement, the drivers will finish installing. Reboot your computer after the install is complete.
Installing the Touch Driver-IntelliTouch Plus Touchscreen Technology *Multi-touch Support *USB *Single monitor *Windows 7 ONLY Follow the directions on the screen to complete the driver setup for your Windows 7 system. 1. Insert the Elo CD-ROM in your computer’s CD-ROM drive. 2. EloSetup launches. 3. Click “Install Driver for This Computer.” 4. Click “Install drivers for all other Elo USB interfaces.” 5. Click the “Install” button.
6. Review and accept the license agreement.
7. The touch driver setup is complete.
Chapter 3 – Mounting General Mounting Information The OSD text can be rotated through the OSD menu to better suit your mounting orientation. Rear VESA Mount A four-hole 75x75mm mounting pattern for M4 screws is provided on the rear of the monitor. The VESA FDMI-compliant counting is coded: VESA MIS-D, 75, C.
User Manual – 1940L SW601787 Rev A Page 12 of 26
Side Bracket Mount Threaded holes are provided on the sides of the monitor for mounting using the provided brackets.
Chapter 4 – Operation Power To turn the touchmonitor on or off, press the touchmonitor power button once. The Power Status LED on the REMOTE OSD controller functions according to the following table: TouchMonitor/Computer Module status LED status OFF OFF SLEEP PULSING ON ON The system consumes low power when in SLEEP and OFF modes. For detailed power consumption specifications, refer to technical specifications on the Elo website http://www.elotouch.
Select “Match Touch to Display…” to calibrate multiple monitors. Projected-Capacitive Touch Technology When connected to Windows 7 computers, the touchmonitor can report 2 simultaneous touches. When connected to Windows XP computers, the touchmonitor reports single touches. No additional drivers are required for this touch technology to work, it uses Windows HID drivers. No calibration is required for this touch technology.
Video A display’s native resolution is its width and height measured in number of pixels. Generally, for best performance, an image displayed on this monitor will look best when your computer’s output resolution matches this monitor’s native resolution of 1366x768. For computer output resolutions at non-native resolutions, the monitor will scale the video to its panel’s native resolution.
On-Screen Display (OSD) Five OSD buttons are located on REMOTE OSD controller. These can be used to adjust various display parameters.
Switches the scaling method between Full Scaling and Maintain Aspect Ratio. Default: Full Scaling Full Scaling – scales the X- and Y-dimensions of the input video (up or down as needed) to the Aspect Ratio display’s native resolution.
All touchmonitor adjustments made through the OSD are automatically memorized as soon as they are entered. This feature saves you from having to reset your choices every time the touchmonitor is unplugged or powered off and on. If there is a power failure, the touchmonitor settings will not default to the factory specifications. OSD and Power Lockouts Press and hold the “Menu” and “Up” buttons for two seconds to enable/disable the OSD Locking feature.
Chapter 5 – Technical Support If you are experiencing trouble with your touchmonitor, refer to the following suggestions. If the problem persists, please contact your local dealer or contact Elo TouchSystems Customer Service. Solutions to Common Problems Problem The touchmonitor does not respond when turning on the system. Monitor display is dim Monitor display is blank.
Chapter 6 - Safety & Maintenance Safety To avoid risk of electric shock, follow all safety notices and do not disassemble the touchmonitor. They are not user-serviceable. The slots located on the sides and top of the touchmonitor case are for ventilation. Do not block or insert anything inside the ventilation slots. Ensure that your installation is equipped to maintain the specified environmental conditions listed in the Technical Specifications chapter.
Chapter 7 – Regulatory Information I. Electrical Safety Information: Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. There are no operator serviceable parts inside this equipment.
iii) Reorient the affected receiver’s antenna. iv) Plug the digital device into a different AC outlet so the digital device and the receiver are on different branch circuits. v) Disconnect and remove any I/O cables that the digital device does not use.(Unterminated I/O cables are a potential source of high RF emission levels.) vi) Plug the digital device into only a grounded outlet receptacle. Do not use AC adapter plugs.
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this component is below the limit requirement in SJ/T11363-2006. X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this component is above the limit requirement in SJ/T11363-2006. For items marked with X, exemptions were taken according to EU RoHS. Explanation of Markings (1).
Chapter 8 – Warranty Information Except as otherwise stated herein, or in an order acknowledgment delivered to Buyer, Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship. The warranty for the TouchMonitors, and their components is 3 (three) years. Seller makes no warranty regarding the model life of components. Seller’s suppliers may at any time and from time to time make changes in the components delivered as Products or components.
Check out the Elo TouchSystems Website! www.elotouch.com Get the latest... Product Information Specifications News on upcoming events Press releases Software drivers TouchMonitor Newsletter Getting in Touch with us To find out more about the extensive range of Elo touch solutions, visit our Website at www.elotouch.
