Touchmonitor User Guide 1537L 15” LCD Rear-Mount Touchmonitor
Elo Touch Solutions 1537L 15” LCD Touchmonitor Optional Power Brick User Guide Revision C P/N E783501 Elo Touch Solutions 1-800-ELOTOUCH www.elotouch.
Copyright © 2012 ELO Touch Solutions. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of ELO Touch Solutions. Disclaimer The information in this document is subject to change without notice.
Table of Contents Chapter 1 Introduction Appendix B 1 Touchmonitor Safety ...................................................22 Care and Handling of Your Touchmonitor ...................23 Warning ......................................................................23 Product Description ....................................................1 Precautions.................................................................1 Chapter 2 Installation and Setup ...................................
CHAPTER 1 INTRODUCTION Product Description Your new touchmonitor combines the reliable performance of touch technology with the latest advances in (LCD) display design. This combination of features creates a natural flow of information between a user and your touchmonitor. This LCD monitor incorporates a 15” color active matrix thin-film-transistor (TFT) to provide superior display performance. A maximum resolution of XGA 1024 x 768 is ideal for displaying graphics and images.
About the Product Your LCD kiosk touchmonitor is a 15” XGA TFT color display with the following features: • The internal microprocessor digitally controls auto-scanning. For horizontal scan frequencies between 31.5 KHz and 60.2 KHz, and vertical scan frequencies between 56.3 Hz and 75.0 Hz. In each frequency mode, the microprocessor-based circuitry allows the monitor to function at the precision-of a fixed frequency. • High contrast color TFT LCD display support resolution up to XGA 1024 x 768.
CHAPTER 2 INSTALLATION AND SETUP This chapter discusses how to install your LCD touchmonitor and how to install the driver software.
Power cable for European models (exclude NPB models) Europe/VDE power cable Power cable for Japan models (exclude NPB models) Japanese/PSE power cable Adapter/Terminal Power cable for Asia models (exclude NPB models) and and or or China/CCC power cable Taiwan/BSMI power cable Korea/KC power cable Power cable for Worldwide models (exclude NPB models) USA/UL Power cable Europe/VDE power cable 2-4
Interface Connection Note: Before connecting the cables to your touchmonitor and PC, be sure that the computer and touchmonitor are turned off. 1 Adapter 3 Video Cable 2 Serial Cable 2 USB Cable 5 OSD Remote Control Key (option) 1 Adapter 3 Video Cable 2 USB Cable 5 OSD Remote Control Key (option) 1. Connect one end of the power adapter to the monitor and the other end to the connector of the power cord. 2.
Product Overview Main Unit Rear View 2-6
Installing the Driver Software ELO Touch Solutions provides driver software that allows your touchmonitor to work with your computer. Drivers are located on the enclosed CD-ROM for the following operating systems: • Windows 7 • Windows Vista • Windows XP • Windows 2000 • Windows Me • Windows 98 • • • • Windows 95 Windows NT 4.0 Windows 3.1 MS-DOS Additional drivers and driver information for other operating systems are available on the ELO Touch Solutions web site at www.elotouch.com.
Installing the Serial Touch Driver (not applicable to Acoustic Pulse Recognition and IntelliTouch Plus monitors) Installing the Serial Touch Driver for Windows 7, Windows Vista, Windows XP, Windows 2000, Me, 98/95 and NT 4.0 NOTE: For Windows 2000 and NT 4.0 you must have administrator access rights to install the driver. 1 Insert the ELO CD-ROM in your computer's CD-ROM drive. 2 If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the CD and starts the setup program.
Installing the Serial Touch Driver for Windows 3.1 and MS-DOS You must have a DOS mouse driver (MOUSE.COM) installed for your mouse if you wish to continue using your mouse along with your touchmonitor in DOS. To install Windows 3.x and MS-DOS from Windows 98/95, follow the directions below: 1 Insert the CD-ROM in your computer’s CD-ROM drive. 2 From DOS, type d:\EloDos_W31 to change to the correct directory on the CD-ROM (your CD-ROM drive may be mapped to a different drive letter).
Installing the USB Touch Driver Installing the USB Touch Driver for Windows 7, Windows Vista, Windows XP, Windows 2000, ME and Windows 98. 1 Insert the ELO CD-ROM in your computer’s CD-ROM drive. If Windows 2000 or Windows 98 starts the Add New Hardware Wizard, do the following: 2 Choose Next. Select “Search for the best driver for your device (Recommended)” and choose Next.
CHAPTER 3 OPERATION About Touchmonitor Adjustments Most likely there will be no need to be adjust your touchmonitor. However, variations in video output and application may require adjustments to optimize display quality. For best performance, your touchmonitor should be operating in native resolution, that is 1024 x 768 at 60k-75 Hz. Use the Display control panel in Windows to choose 1024 x 768 resolution. Operating in other resolutions will degrade video performance.
Rear Panel Controls SEL MENU 1 2 Control 1 Menu/Exit 2 3 4 5 Function Display/exits the On Screen Display (OSD) menus. 1. Enter contrast of the OSD. 2. Increase value of the adjustment item. 3. Select item clockwise. 3 4 Select 1. Enter brightness adjustment. 2. Decrease value of the adjustment item. 3. Select item counter-clockwise. Selects the adjustment items from the OSD menus. 5 Power Switch Switches the power of the monitor.
Controls and Adjustment OSD Menu Functions To Display and Select the OSD Functions: 1 Press the Menu key to activate the OSD menu. 2 Use or to move counter-clockwise through the menu. Press the Enter key, the parameter will be highlighted when selected. 3 To quit the OSD screen at any time during the operation, press the Menu key. If no keys are pressed for a short time period, the OSD automatically disappears.
OSD Control Options Control Contrast Brightness V-Position H-Position Recall Defaults Description Increases or decreases contrast. Increases or decreases brightness. Moves the screen up or down. Moves the screen left or right. Returns the monitor to its default settings. RGB Press or to select 9300, 6500, 5500, 7500 and USER. Only when selecting USER can you make adjustments to the R/G/B content. Press Enter to restore to factory default setting. Exit the menu.
Preset Modes To reduce the need for adjustment for different modes, the monitor has default setting modes that are most commonly used as given in the table below. If any of these display modes are detected, the monitor automatically adjusts the picture size and centering. When none of the mode is matched, the user can store their preferred modes in the user modes. The monitor is capable of storing up to 7 user modes.
Power Management System The monitor is equipped with the power management function which automatically reduces the power consumption when not in use. Mode On Sleep Off Power Consumption <30W <3W <1W We recommend switching the monitor off when it is not in use for a long time. NOTE: Complies to VESA Power Management (DPM) standards. To activate the monitor, press any key on the keyboard or move the mouse or touch the touchscreen.
IntelliTouch Plus Touch Technology When connected to Windows 7 computers, the touchmonitor can report 2 simultaneous touches. The IntelliTouch Plus touchscreen can be re-calibrated to your displayed video image, if needed, through the Calibration function in the ELO driver control panel. The IntelliTouch Plus driver will only support multiple monitor if they are all using the IntelliTouch Plus touch technology.
Gesture Support The IntelliTouch Plus touch technology enable several gestures that support single and multiple contacts. Refer to the Microsoft Website http://msdn.microsoft.com/en-us/library/dd940543 on the various gestures that are supported in Windows 7.
CHAPTE R 4 TROUBLESHOOTING If you are experiencing trouble with your touchmonitor, refer to the following table. If the problem persists, please contact your local dealer or our service center. Solutions to Common Problems Problem The monitor does not respond Suggestion(s) Check that the monitor’s Power Switch is on. after you turn on the system Turn off the power and check the monitor’s power cord and signal cable for proper connection.
APPENDIX A NATIVE RESOLUTION The native resolution of a monitor is the resolution level at which the LCD panel is designed to perform best. For the LCD touchmonitor, the native resolution is 1024 x 768 for the 15 inch size. In almost all cases, screen images look best when viewed at their native resolution. You can lower the resolution setting of a monitor but not increase it.
As an example, a SVGA resolution LCD panel has 800 pixels horizontally by 600 pixels vertically. Input video is also represented by the same terms. XGA input video has a format of 1024 pixels horizontally by 768 pixels vertically. When the input pixels contained in the video input format match the native resolution of the panel, there is a one to one correspondence of mapping of input video pixels to LCD pixels.
APPENDIX B TOUCHMONITOR SAFETY This manual contains information that is important for the proper setup and maintenance of your touchmonitor. Before setting up and powering on your new touchmonitor, read through this manual, especially Chapter 2 (Installation), and Chapter 3 (Operation). 1 To reduce the risk of electric shock, follow all safety notices and never open the touchmonitor case. 2 Turn off the product before cleaning.
Care and Handling of Your Touchmonitor The following tips will help keep your touchmonitor functioning at the optimal level. • To avoid risk of electric shock, do not disassemble the display unit cabinet. The unit is not user serviceable. Remember to unplug the display unit from the power outlet before cleaning. • Do not use alcohol (methyl, ethyl or isopropyl) or any strong solvent. Do not use thinner or benzene, abrasive cleaners or compressed air.
APPENDIX C TECHNICAL SPECIFICATIONS C-24
Touchmonitor Specifications Model LCD Display Display Size Pixel Pitch Display Mode 1537L 15” TFT Active Matrix Panel 304.1(H) x 228.1(V) mm 0.297(H) x 0.297(V) mm VGA 640 x 350 (70Hz) VGA 720 x 400 (70Hz) VGA 640 x 480 (60 / 72/ 75Hz) SVGA 800 x 600 (56 / 60 / 72/ 75Hz) XGA 1024 x 768 (60 / 70 / 75Hz) Max.
15" LCD Touchmonitor (1537L) Dimensions 357' 4 c I ii !I':H:tli fio"o"o"o"o"ogol / o6 @ c 00 0 0 0 0 0 0 0 0 0c 0 00 • 85.4 0 0 0 0 0 0 0 0 0 0 0 'lJ • • 3 000 000 0 0 0 000 0 0 0 0 § CCC 000 • • ?. occ c..- ·"-- c il I ); · • • 0 0 0 0 0 @ Qooo occ T [ 0 L 'i=-, c o) r--10o-Js- ii • • II 0 (}gg 000 • 0! • § CCC .\ 0 0 0 0 00 0 00 0 00 0 00 I OODOOO 00000"0
REGULATORY INFORMATION I. Electrical Safety Information: A) Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. B) There are no operator serviceable parts inside this equipment.
D) General Information to all Users: This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to this manual the equipment may cause interference with radio and television communications. There is, however, no guarantee that interference will not occur in any particular installation due to site-specific factors.
III.
WARRANTY Except as otherwise stated herein or in an order acknowledgment delivered to Buyer, Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship. The warranty for the touchmonitors and components of the product is regional; please contact your regional office. Seller makes no warranty regarding the model life of components. Seller’s suppliers may at any time and from time to time make changes in the components delivered as Products or components.
THESE REMEDIES SHALL BE THE BUYER’S EXCLUSIVE REMEDIES FOR BREACH OF WARRANTY. EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, SELLER GRANTS NO OTHER WARRANTIES, EXPRESS OR IMPLIED BY STATUTE OR OTHERWISE, REGARDING THE PRODUCTS, THEIR FITNESS FOR ANY PURPOSE, THEIR QUALITY, THEIR MERCHANTABILITY, THEIR NONINFRINGEMENT, OR OTHERWISE. NO EMPLOYEE OF SELLER OR ANY OTHER PARTY IS AUTHORIZED TO MAKE ANY WARRANTY FOR THE GOODS OTHER THAN THE WARRANTY SET FORTH HEREIN.
Check out Our Website! www.elotouch.com Get the latest... • Product information • Specifications • News on upcoming events • Press release • Software drivers • Touchmonitor Newsletter Getting in Touch with us To find out more about ELO’s extensive range of ELO Touch Solutions, visit our website at www.elotouch.
