Datasheet

Keep-Current service means, that ELNEC ships the latest version of programmer software and updated
user documentation (Keep-Current package) to customer . The Keep-Current service is your hassle-free
guarantee that you achieving the highest quality programming on ELNEC programmers, at minimal
cost.
Prompt delivery
Combination of extensive stock, flexible manufacturing and shipping of Elnec products by world class
carriers (like DHL) warrants customers very fast and secure delivery of ordered Elnec products. Products
ordered before 10 a.m. (CET) will be dispatched the same working day (if products are in stock and the
payment is done by Online payment (CardPay, PayPal).
Warranty
Advanced design of the BeeProg2 universal programmer, including protective circuits, original brand
components, careful manufacturing and burning-in allow us to provide a three-year warranty on parts
and workmanship of the programmer (limited 25 000-cycle warranty on ZIF sockets).
Elnec provides free shipping of programmer repaired under warranty back to customer world
wide. Warranty is valid from the date of purchase.
Preferential handling of repair requests ensures registration of the product that should be done within
60 days from the date of purchase here.
Specification
HARDWARE
Base unit, DACs
USB 2.0 high-speed compatible port, up to 480 Mbit/s transfer rate
FPGA based IEEE 1284 slave printer port, up to 1MB/s transfer rate
on-board intelligence: powerful microprocessor and FPGA based state machine
three D/A converters for VCCP, VPP1, and VPP2, controllable rise and fall time
VCCP range 0..8V/1A
VPP1, VPP2 range 0..26V/1A
autocalibration
selftest capability
protection against surge and ESD on power supply input, parallel port connection
banana jack for ESD wrist straps connection
banana jack for connection to ground
ZIF socket, pindriver
48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil devices up to 48-pin
pindrivers: 48 universal
VCCP/VPP1/VPP2 can be connected to each pin
perfect ground for each pin
FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins
analog pindriver output level selectable from 1.8 V up to 26V
current limitation, overcurrent shutdown, power failure shutdown
ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV contact)
continuity test: each pin is tested before every programming operation
ISP connector
20-pin male type with missinsertion lock
6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable from 1.8V up to 5V to handle all
(low-voltage including) devices.
1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins
programmed chip voltage (VCCP) with both source/sink capability and voltage sense
1x VPP voltage (range 2V..25V/50mA), can be applied to six pins
target system supply voltage (range 2V..6V/250mA)
ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV air, 8kV contact)
two output signals, which indicate state of work result = LED OK and LED Error (active level: min 1.8V)
input signal, switch YES! equivalent (active level: max 0.8V)
DEVICE SUPPORT
Programmer, in ZIF socket
EPROM: NMOS/CMOS, 2708*, 27xxx and 27Cxxx series, with 8/16 bit data width, full support for LV series
EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series, with 8/16 bit data width
Flash EPROM: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx, 29LVxxx, 29Wxxx, 49Fxxx series, Samsung's K8Fxxxx,
K8Cxxxx, K8Sxxxx, K8Pxxxx series, from 256Kbit to 1Gbit, with 8/16 bit data width, full support for LV series
NAND FLASH: Samsung K9xxx, Hynix HY27xxx, Toshiba TC58xxx, Micron MT29Fxxx, Spansion S30Mxxx,
Numonyx (ex STM) NANDxxx