Instruction Manual
IMPORTANT SAFETY INSTRUCTIONS Your Elna 7200 sewing machine is designed and constructed for HOUSEHOLD use only. Read all instructions before using this machine. DANGER – To reduce the risk of electric shock: 1. Your sewing machine should never be left unattended when plugged in. Always unplug the machine from the electrical outlet immediately after using and before cleaning. 2. Always unplug before replacing light bulb. Replace bulb with same type rated 12 Volts, 5 watts. 3.
TABLE OF CONTENTS SECTION I – Machine Parts and Functions SECTION IV - Quilting Part Names .............................................................................. 3 Standard Accessories ............................................................. 4 Presser Foot and Accessory Definitions .............................. 5-6 How to Attach Stitch Chart Brackets ....................................... 7 Stitch Chart ..............................................................................
r t y u SECTION I i o e Machine Parts and Functions !0 w Part Names !1 1. Stitch chart brackets (to attach, see page 7) 2. Foot pressure dial 3. Thread take-up lever 4. Thread guide plate 5. Stitch chart 6. LCD screen brightness control 7. Retractable thread guide (pull up) 8. Bobbin winder spindle 9. Bobbin winder stop 10. LCD screen 11. Selection keys (see pages 11–13) 12. Speed control lever 13. Centimeter/inch quick measurements 14. Feed dog lever 15. Knee lifter insert channel 16.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Standard Accessories 1. A: Standard metal foot (attached to machine) 2. B: Buttonhole foot (4-step) 3. C: Overlock foot 4. D: Hemmer foot 5. E: Zipper foot 6. F: Satin stitch foot 7. F-2:Open toe satin stitch foot 8. G:Blind hem foot 9. H: Multi-cord foot 10. Scant 1/4˝ foot 11. P-2:Open toe embroidery/darning foot 12. R: Automatic buttonhole foot 13. Open toe walking foot 14. Quilt guide 15. Straight stitch needle plate 16.
Presser Foot and Accessory Definitions A: Standard Metal Foot This foot comes attached to your machine. It is mainly used for straight stitches and zigzag stitches longer than 1.0. The button locks the foot in a horizontal position helping to sew over multiple layered seams. B: Buttonhole Foot Sew oversized buttonholes for novelty buttons or a decorative accent. The two cutout grooves on the underside of the foot ensure that the buttonhole sides lie parallel to each other.
H: Multi-Cord Foot Design your own braids or trims. Place one to three cords in the foot and sew over cord(s) for a simple couching method. Or sew over one cord with a zigzag to gather heavier weight fabrics. Scant 1/4˝ Foot Accuracy is the key to successful patchwork/quilt sewing. Sewn from 3.5 needle position; the edge of the foot provides a perfect 1/4˝ seam guide. Or use 4.5 needle position and achieve the desirable scant 1/4˝ often requested by quilters.
How to Attach Stitch Chart Brackets Align the screws with the holes on the backside of the machine. Firmly tighten screws with screwdriver. Stitch Chart w q The stitch chart can be placed in two positions on the chart bracket, store or view. w q e Store Position The back slots q on the bracket are for store position e. Slide stitch chart down between the back slots until the stitch chart rests against machine bed. r View Position The front slots w on the brackets are for view position r.
Quilt Table The table provides more sewing surface to support large fabric pieces to make sewing easier. Assemble table by attaching six legs to underside of quilt table with screws. Attaching Table to Machine Fit the table around the machine, as shown in the illustration. If necessary, adjust height of legs to level table with machine bed by tightening or loosening leg screws. Knee Lifter The knee lifter allows you to raise or lower the presser foot without using your hands.
Connecting Machine To Power Supply Before connecting the power cord, make sure the voltage and frequency shown on the machine are identical to your electrical power. q To connect machine to power supply, turn off the power switch q. Insert the foot control plug w and machine plug e into the machine and the power supply plug r into the wall socket. e Your machine may come equipped with a polarized plug (one prong wider than the other). A polarized plug reduces the risk of electrical shock.
Main Function of Keys q Start/Stop Key (changes color to indicate function) t Press this (green) key to start the machine. The first few stitches will be sewn at a slow speed and then machine sews at the speed set by the speed control lever. Press (red) key again to stop machine. Press and continue to hold key down to sew at slow speed, release key to sew at set speed. Press key again to stop. r e w q NOTE: The foot control must be detached to use this key.
Keyboard Selection Keys !9 q e r t y u i o !0 w 1. !1 !2 !3 !4 !5 !6 !7 LCD Screen Brightness Control Lighten or darken the screen with this dial. !8 2. Stitch Width and Needle Position Key Press “–” or “+” side of key to change setting. Press “–” or “+” to move needle position left or right. Straight stitches (1, 6, 011, 012, 061, 062 and 063) can be sewn from many needle positions by pressing the “–” or “+” side of the key. Center needle position is 3.5. 3.
8. Memory Save/Recall Key The 3 Digit Mode has four separate memories for saving a sequence of stitches. Press this key to activate memory 1 (M1). Press key again to activate M2. Continue to press this key to access M3, M4 or to exit memory. Once a memory is activated, press the “ENTER” key to save the sequence. To recall a saved memory, press “M” key until desired memory appears. To activate the saved sequence, press “Mirror Image” key. 9.
16. Review Memory Right Key Use this key to review stitches in a memorized sequence when all stitches do not appear on the screen. OR Press this key to move the cursor right until it is under the stitch that will be edited. 17. Memory Auto Thread Cut Key Press this key after selecting a stitch and when the Auto-Lock key is pressed the machine will automatically cut threads after lockstitching is completed.
Setting Quick Resumption, Sound and Language Modes These three modes/functions can be set according to your preferences. Each new setting requires you to turn OFF the power switch. Turn ON the power switch while pressing “ENTER” key. Message screen appears. Press “1” key to change quick resumption or “2” key to change sound or “3” key to change language. z x Quick Resumption – The last stitch or memorized sequence of stitches that were sewn will appear when machine is switched on. z Press “1” key.
Reset to Factory Default It is possible to reset the machine to the factory defaults with English language as default. Turn OFF the power switch. Press “ENTER” key while turning power switch ON. Message screen appears. Press “0” key. Message screen appears. Press “ENTER” key to confirm and reset to factory default. OR Turn off power switch to cancel the reset. Controlling Sewing Speed Sewing speed can be varied with the foot control. The harder you press on the foot control, the faster the machine runs.
How To Drop the Feed Dog The feed dog can be dropped out of position for special sewing techniques: free motion embroidery, stippling, button sewing, etc. q The feed dog must always be up for regular sewing. The machine will run with the feed dog down if the following stitches are selected: 1, 2, 3, 4, 011, 014, 015, 016, 017, 042, 061 and 062. The machine will not sew with the feed dog down if any other stitches are selected.
Attaching and Removing Presser Feet Press the “Up/Down Needle” key until the needle is in the raised position. Turn OFF the power switch. Raise the presser foot and press the red button q on back of the shank. The presser foot will drop off. q e w Place the selected presser foot so the pin e on the foot lies just under the groove w of the shank. Lower the presser bar and attach the foot. Attaching and Removing Shank Turn OFF the power switch. Raise the presser bar.
Adjusting the Needle Thread Tension w Choosing the Correct Tension - Straight Stitch The ideal straight stitch will have threads locked between the two layers of fabric. According to the LCD screen, needle thread tension can range from 2 – 6 q and is normally set on 4. Align the number 4 on the tension dial with the setting mark w. q If you look at the needle thread e (top thread) and bobbin thread r (bottom thread), you will notice that there are no gaps. Each stitch is smooth and even.
Using the Fine Adjustment Screw Choice of fabrics and threads may affect the stitch formation when sewing decorative stitches, letters and numbers or classic 4 step memory buttonhole (071). The fine adjustment screw can be used to either lengthen or shorten the stitch. q Fine adjustment screw w Standard mark e Setting mark w To fine tune, use a screwdriver to move the setting mark. q e r t • If stitches are too short r, correct by turning the screw in the direction of “+”.
Weight Fabric Needle Type Very Light Light Universal Ball Point Stretch Chiffon, Fine Lace, Organdy Batiste, Lawn, Crepe de Chine, Challis, Handkerchief Linen, Crepe, Taffeta, Satin Universal Single Knits, Jersey, Swimwear, Tricot Leather, Suede Medium Flannel, Velour, Velvet, Velveteen, Corduroy, Linen, Gabardine, Wool, Terry, Burlap Double Knits, Stretch Velour, Stretch Terry, Sweater Knits Leather, Vinyl, Suede Heavy Denim, Sailcloth, Ticking Coating, Polar Fleece, Drapery, and Upholstery Fabrics L
Needle Definitions The illustration identifies the main parts of a sewing machine needle. q Body w Shaft e Long groove (round side of needle) r Short groove (flat side of needle) t Eye y Point q w Universal – an all-purpose needle that handles most woven and knit fabrics. Ball point – the point spreads the fibers, preventing tears and is especially suited for loose knits and interlock knits. Not recommended for embroidery.
Winding a Bobbin To remove bobbin, slide bobbin cover plate release button q to the right and lift away the bobbin cover plate w. q w Lift out the bobbin e. Turn ON the power switch. e CAUTION: Avoid using a bobbin if it is almost empty, as thread may tangle. Always use bobbin type supplied with machine. Pull up the retractable thread guide r. r y u Place the spool of thread t on the right side spool pin y with the thread coming off the spool as shown.
Pull the thread up and through the right retractable thread guide q from behind. q Pull the thread under and around the bobbin winding tension disc w. w Pass the thread through the hole in the bobbin e from inside to the outside. Place the bobbin on the bobbin winder spindle r. e r Push bobbin winder stop t to the left. t y Holding the free end of the thread, press the “Bobbin Winding” key y. (A separate motor winds the bobbin, allowing you to sew at the same time bobbin winding occurs.
Inserting the Bobbin Place the bobbin in the bobbin case with the thread running counterclockwise. Guide the thread into notch q on the front side of the bobbin case. q Hold the bobbin with your right hand and pull the thread to the left, through the tension spring blades w. w Continue pulling the thread lightly until the thread slips into notch e. Pull out about 15 cm (6˝) of thread. e Replace the bobbin cover plate. Refer to the chart shown on the bobbin cover plate to check the threading.
Threading the Machine r e Raise the presser foot. Press the “Up/down Needle” key until the needle is in an up position. q Place the spool of thread on the left spool pin with the thread coming off the spool as shown and attach the spool holder. w Pull the thread up and through the left retractable thread guide q from behind. Pull the thread under the upper thread guide w. Using both hands, firmly insert the thread under the thread guide plate e. e Pull thread forward under the left thread guide r.
r u e t y i o Continue to pull the thread down into the right channel and around the tension dial from right to left. Pull up on the thread until it is inserted between the tension discs and under the loop of the check spring t. Check that the thread is coming out over the notch y of the disc. y t Pull thread up the left channel to the take-up lever. Pass thread from right to left side down into eye of take-up lever u. u i Proceed down to the lower thread guide i and pull thread left.
Built-in Needle Threader Press the “Up/Down Needle” key q until the needle is in an up position. Turn OFF the power switch. Lower the presser foot. q Lower the needle threader lever w as far as it will go. Hook e is automatically inserted into the needle eye. w e Bring the thread around guide r and under hook e. e r Slowly release the lever while holding the thread end and let the needle threader return to its original position. A loop of thread t is pulled through the needle eye.
Drawing Up the Bobbin Thread Turn ON the power switch. Raise the presser foot and hold the needle thread lightly with your left hand. Press the “Up/Down Needle” key q twice to pick up the bobbin thread. q Draw up the needle thread together with a loop of bobbin thread. Slide 10 cm (4˝) of both threads to the back under the presser foot.
SECTION III Basic Sewing z How to Select a Stitch z Select stitches 1 – 0 in Direct Select Mode by touching the corresponding key. x Select stitches in the 3 Digit Mode by pressing “MODE” key and then the 3 corresponding keys. x Set-up your machine according to the LCD screen. See page 13. Straight Stitch When the machine is turned on, it is automatically set to sew a straight stitch in the center needle position (Exception: Quick Resumption Mode. See page 14).
Cutting the Threads After sewing is stopped, press the “Auto Thread Cut” key q (LED signal turns on). (Needle should be in down position before using auto thread cutting mechanism to avoid extra needle penetrations.) q Raise the presser foot and remove the fabric. Pull both threads to the back under the presser foot so they are ready for sewing again. w OR Specialty or heavy decorative threads: Press the “Up/Down Needle” key to raise the needle. Raise the presser foot.
Adjusting Stitch Length When you press the “Stitch Length” key, the stitch length can be set at 0.00 or between 1.0 and 5.0. Press the top “–” side of the key to shorten the stitch length. Press the bottom “+” side of the key to lengthen the stitch length. 1.0 2.5 5.0 Programming My Personal Settings Stitches 1-126 can be programmed to override the factory default settings. z z Change stitch length to 2.6. x x Press “My Personal Setting” key. Message screen appears.
Reset Stitch To Factory Default Settings z It is possible to reset the machine so personal settings for an individual stitch revert to the factory default settings. z Display the stitch you want to reset in the LCD screen. x Press “My Personal Setting” key. Message screen appears. x c Press “C” key. PS symbol disappears and factory default settings are displayed.
Sewing On Heavy Fabrics The black button on presser foot “A” locks the foot in a horizontal position when pushed in before lowering the presser foot. This ensures even feeding at the beginning of seams and helps when sewing many layers of fabric such as welt seams used to hem jeans. When the point of an increased thickness is reached, lower the needle and raise the presser foot. Press in the black button. Lower the foot and continue sewing.
Zipper Insertion Lapped Application Lapped zippers are usually inserted into a side seam of skirts or pants, for example. Use zipper foot E instead of standard metal foot A. Attach the pin on zipper foot E to the groove on the shank. • To sew the left side of the zipper, attach the zipper foot on the right-hand side. • To sew the right side of the zipper, attach the zipper foot on the left-hand side. Fabric Preparation Add 1 cm (3/8˝) to the zipper size.
Close zipper. Turn zipper face up (right seam allowance forms a small fold at basting line) and smooth zipper teeth away from seam. Attach foot with right side pin. Reset straight stitch length to 2.5. Starting at the bottom, sew through the folded seam allowance and zipper tape. Stop just before the zipper foot reaches the slider on the zipper tape. Lower the needle slightly into the fabric. Raise the zipper foot and open the zipper. Lower the foot and stitch the remainder of the seam.
Rolled Hem An easy, professional way to sew hems. The spiral on the hemmer foot guides the fabric edge to create a rolled hem. Recommended for fine, sheer fabrics used in bridal wear. Attach hemmer foot D. Trim about 6.5 mm (1/4˝) from corners to reduce bulk. Make a double 3 mm (1/8˝) fold approximately 8 cm (3˝) in length. Align fabric hem edge with the inside of right extension of foot q. Use this placement on foot as guide. Lower presser foot. Sew 3 or 4 stitches while holding needle and bobbin threads.
Zigzag Stitch The zigzag stitch is a very versatile stitch. Simply change its width and length. Use the zigzag to finish raw seam edges, sew narrow hems, sew satin stitch appliques and create beautiful monograms. Select 2. q w e r Adjusting Stitch Width and Length Press the “–” or “+” side of the keys to change the stitch width and length.
Satin Stitch Appliqué The zigzag stitch is commonly used for appliqué, monogramming, stems of flowers and petals. (A short zigzag stitch length creates the satin stitch.) Threads of 100% cotton, rayon or silk provide the best results. • Apply stabilizer to the fabric for the stitch to form correctly. Select 2. Attach satin stitch foot F. Decrease stitch width to 3.5 and stitch length to 0.40. Appliqué Preparation 1. Press fusible webbing to the wrong side of a lightweight fabric. 2. Cut out design shape.
Mending a Tear Pull torn edges together and fuse a piece of interfacing slightly larger than the tear to the wrong side of the garment. Select 3. Decrease stitch length to 0.20 – 0.50. Begin sewing above the tear. Stitch down the middle, pulling edges together. Stop sewing just beyond end of tear. Depending on the tear, you might need to stitch area 2 or 3 times. Serpentine Stitch A delicate curve that is great for topstitching or for applying elastic directly to fabric without making an elastic casing.
Blind Hem Stitches The stretch blind hem (5) is a great method for finishing a hemline or sleeve. Use the woven blind hem (064) on non-stretch fabrics. Finish the raw hem edge with a zigzag or 3 step zigzag q before sewing the blind hem. Select 5 or press “MODE” key and select 064. Fold up the hem allowance and press. Fold under the hem toward right side of garment. Leave a 6.5 – 10 mm (1/4˝ to 3/8˝) extension e at the right.
Buttonhole Variations All buttonholes should use interfacing that is the same weight as the fabric. Interfacing is especially important when sewing on stretch fabrics. 0 or 071 072 073 074 075 076 Classic Buttonhole (Sensor or 4 Step Memory) The most common buttonhole, found on blouses, shirts, pants, etc. It consists of a bartack at each end and a compact zigzag stitch along each side. Classic Keyhole Buttonhole Accommodates the shank found on large buttons used on heavy coats and jackets.
Sensor Buttonholes (Totally Automated Buttonholes) Select a buttonhole - 0, 072 thru 075. The LCD screen will briefly show a message advising that the buttonhole lever must be lowered. Alter the buttonhole width to match the fabric and thread. See page 45. When attaching buttonhole foot (R), make sure the button opening is at the back of the foot. Extend the buttonholder q to the back and place the button in it. Push the holder together tightly around the button.
Mark the buttonhole area on the fabric. Place both threads to the left under the foot. Insert the garment under the foot and hand turn the flywheel to lower the needle at the starting point. Lower the buttonhole foot. q Memory Auto Thread Cut Key w It is possible to program the machine to automatically cut the threads when a buttonhole is completed. To program - press the “Memory Auto Thread Cut” key q after selecting the buttonhole and before sewing begins; the LED light w will turn on. Begin sewing.
q w Press “MODE” key to access 3 Digit Mode for Buttonholes 072 – 076.
Cutting Open Buttonhole Place a pin just inside the bartack at each end to prevent accidentally cutting bartacks. Cut buttonhole open with the seam ripper. Troubleshooting Tips If the button is extremely thick and difficult to fit through the test buttonhole, you can lengthen the buttonhole by pulling the buttonholder on the foot back a little extra. The length of the hole will increase by that same amount. q Make sure there is not a gap between the slider and the spring holder.
Corded Buttonhole Corded buttonholes are found on coats and other garments that require extra strong buttonholes. The cording reinforces and accentuates the buttonhole. Sew a corded buttonhole using the same procedure as described for a classic buttonhole. • Set the stitch width to match the thickness of the cording. w q With the buttonhole foot raised, hook the filler cord q on the spur w at the back of the buttonhole foot. Bring the ends forward under the buttonhole foot.
071 Classic Buttonhole (4 Step Memory) The classic buttonhole is especially suited for oversized novelty buttons or larger decorative openings for weaving curtain rods and scarves, for example. All buttonholes should use interfacing suitable for the fabric weight. Test sew the buttonhole on sample swatch. Select 071. The LCD will briefly show two messages. Use either the R or B buttonhole foot. If you use the R foot, fully extend open the buttonholder q (maximum buttonhole size with this foot is 3.
Start sewing – front bartack, lockstitch. Machine will automatically stop when buttonhole is completed. Sewing Additional Buttonholes To sew another buttonhole the same size - raise foot, move fabric, lower foot and sew. Reset Buttonhole Size To sew a buttonhole a different size (or to adjust stitch length), reset the machine by pressing “ENTER” key or reselect buttonhole. Sew new buttonhole size using same method.
076 Bound Buttonhole (4 Step Memory) Great for oversized buttons requiring tailored buttonholes, welt pockets or larger decorative openings. All buttonholes should use interfacing suitable for the fabric weight. Test sew the buttonhole on sample swatch. Select 076. The LCD screen will briefly show two messages. Increase stitch length so it is appropriate for your fabric weight. Attach buttonhole foot B. (You could use the R buttonhole foot. If you use R foot, fully extend the buttonholder open.
, Start sewing – straight stitch front edge, lockstitch. Machine will automatically stop when buttonhole is completed. , . . Cut down center of sewn rectangle, snipping into each corner. ⁄0 ⁄0 Pass the bias square through slit and pull to wrong side of garment to form the lips of buttonhole. ⁄1 ⁄1 From wrong side, press lips into center and fold bias fabric over lips forming a tuck at each end. ⁄2 ⁄2 From right side, align lips. Baste and press.
How To Sew On a Button Hand sewing buttons to a garment is very timeconsuming. Sew them on in one quick, easy step. Select 2. Attach satin stitch foot F. Drop the feed dog. See page 16. • Set the stitch width according to the position of the holes in the button. Mark button placement on fabric. Use washable glue or transparent tape to temporarily secure the button. Place the button and fabric under the presser foot. Match the holes in the button to the horizontal slot on the presser foot.
Triple Seam This strong, durable stitch is recommended where both elasticity and strength are needed. Because of its durability, once in place, this stitch is not easily removed. Use it to reinforce areas such as crotch and armhole seams or to construct items such as backpacks. This stitch can also be used for topstitching. Elna invented this stitch in 1952. Using a straight stitch (stitch length 4.0), baste a seam together. Verify the fit. Select 063. Sew final seam.
Super Overlock Stitch This industrial inspired overlock stitch is excellent for assembling and finishing fabrics together in one step. Apply ribbing to knits and garment retains its shape. Elna invented this stitch in 1982. Select 067. Place the fabric edges together under the presser foot next to the right side edge of the presser foot. Super Stretch Stitch This stitch is recommended for sewing fabrics such as swimwear and stretch velour as it provides great stretchability and strength.
Overcast Stitch A reinforced straight stitch and zigzag are sewn simultaneously. If your seam does not need to be opened flat, this stitch will sew the seam and overcast the edge in one operation. Select 070. NOTE: Do not set the stitch width lower than 5.0 when using overlock foot C because the needle could hit wires on the foot. Place the fabric edge against the black guide on the foot. Sew seam. Arrowtack This stitch is used to reinforce the corners of pockets and pleats. Select 077.
Bartacks A bartack is a reinforced stitch used on garment areas that receive extra stress like pockets, belt loops and zippers. Select 078. The LCD screen will briefly show a message. Automatic Bartack Place the fabric under presser foot. Lower presser foot. Sew until the machine automatically stops. A 1.5 cm (5/8˝) bartack is sewn. Press the “Stitch Width/Needle Position” or “Stitch Length” key to adjust bartack. Setting Memory Bartack Size It is possible to sew a bartack length shorter than 1.
Darning Darning with a sewing machine saves a lot of time. It is used for repairing very worn areas (not holes) in fabric. Select 079. The LCD screen will briefly show two messages. Automatic Darning Extend the buttonholder q completely open. Place both threads to the left under the foot. Insert fabric under the foot and lower the needle at the starting point w. Lower the foot. Sew. e q The size of one darning cycle is variable.
Eyelets Small eyelets may be sewn on belts, used for lacing cords or simply used for a decorative effect. Select 080. The machine will sew an eyelet and automatically stop. Cut open the eyelet with a seam ripper, pointed scissors or an awl.
SECTION IV Quilting Piecing Fabrics Together Accuracy is the key when sewing together fabric pieces for a quilt. Be sure to precisely cut your fabric pieces with 6.5 cm (1/4") seam allowances. Select 1. Attach scant 1/4” foot. q The bar on the foot is a perfect 1/4˝ seam guide from center needle position (3.5). Place fabric edges (right sides together) under foot against the guide q and sew a perfect 1/4˝ seam. OR Use 4.5 needle position for a scant 1/4˝ seam.
Walking Foot Great for keeping quilt layers from shifting when sewing and keeping stripes and checks matched. How To Attach Open Toe Walking Foot Press the “Up/Down Needle” key until the needle is in an up position. Raise the presser foot. Turn OFF power switch. Loosen thumbscrew and remove shank. Place the open toe walking foot on the presser bar with the lever over the needle clamp screw; tighten thumbscrew. Turn ON power switch. Select 1. Set stitch length 2.4 - 3.5.
Quilt Guide The quilt guide is helpful when sewing parallel, evenly spaced rows of stitching. Loosen the quilt guide holding screw q, slide the quilt guide in the opening w until the desired width is set and tighten the screw. q Use a washable marker to draw the first line for stitching. Sew over line. When sewing subsequent rows of stitching, the quilt guide will rest on the previous row of stitching.
Buttonhole Appliqué A favorite method of applying small pieces of fabric to quilts for decoration. Select 7 or 019- 024. Use fine embroidery thread (50 weight or finer) and needle appropriate to fabric. You may need to set the foot pressure dial to 2. z x z In this type of appliqué, raw edges are folded under. To prepare raw edge, first cut appliqué design out of paper. c x Press fusible webbing to wrong side of appliqué fabric. c Cut the fabric slightly larger than paper pattern.
Patchwork A fun method of decorating your quilt (often called “Crazy Quilting”) is to sew a patchwork stitch over the opened seam. Select 1. Sew a straight stitch seam and press seam allowance open. Select a patchwork stitch: 8, 013, 014 and 025 – 040. Sew with stitching centered over the seam. Free Motion Quilting or Stippling Add dimension to your quilt by stitching down the surrounding background fabric around larger designs, like hearts or flowers.
Stippling Stitches A pre-programmed stippling stitch is a fast and easy method to quilt small areas. Select 9, 015 or 016. Place batting (wadding) between quilt top and backing fabric. Basting Stitch The basting stitch can be used to temporarily hold together two or more layers of fabric. Use a fine needle to avoid leaving permanent needle marks. Select 011. Lower the feed dog. Set foot pressure dial to 2 or 1. Loosen needle tension to 3. The LCD screen will briefly show a message.
SECTION V Heirloom Pintucks A beautiful accent to any project. Pintucks should be added to your fabric before cutting out the pattern piece. Select 1. Use a washable marker to draw parallel lines for pintucks on fabric right side. Fold fabric on first line with wrong sides together. Place fold under foot and use foot edge as guide. Move needle position to determine the width of the pintuck. Sew pintuck. Sew remaining pintucks using same method. Remove marking lines. Press pintucks to one side.
Hemstitches Hemstitching, also known as French hand sewing, was traditionally only a hand sewn art. There are several stitches to choose from that will add an “old world charm”. Best results require the use of linen, cotton or a blend of linen/cotton. Thread machine, needle and bobbin with a fine cotton embroidery thread (50 weight or finer). Insert a universal needle size #100, #110 or a wing needle (see cautions below). Use spray starch and press to stabilize fabric.
Fringing Fringing adds a special touch on table linens and shawls. Choose a firm, woven fabric like linen where threads can be removed easily. Select 052 (Mirror Image) or 020. z z Carefully cut the fabric on grain. Remove a single yarn or thread where the fringing is to begin. x x Sew down the left side so the right hand stitches fall in the open space. c c Remove all excess yarn located to the right of stitching and create fringe. Drawn Work z Drawn work uses the same method as fringing.
Smocking Smocking is a delicate, decorative treatment on children’s clothing or women’s blouses. Choose a soft, lightweight fabric such as batiste, gingham or challis. Cut the fabric three times the finished width. Select 1. Increase stitch length to 5.0. Sew rows of straight stitches about 10-13mm (3/8"1/2˝) apart, across the area to be smocked. (A looser needle thread tension will make gathering easier.) Tie the threads along one edge. Pull the bobbin threads to distribute the gathers evenly.
SECTION VI Decorative Sewing French Knots Why spend time sewing French Knots by hand? Select 060. Tighten needle tension 5-8. Place fabric under foot and sew one French Knot. Lift up presser foot, move fabric, lower presser foot and sew next French Knot. #060 #062 NOTE: If you want to sew a row of evenly spaced French Knots, you must program straight stitches after the French Knot. See Combining a Sequence on page 74. Scallop Edges Attractively finish edges of collars, pockets and placemats.
Corded Trim Sew over three strands of cording to create unique borders and trims. Pearl cotton, knitting yarn, embroidery floss, lace thread, fine wool or lily yarn may be used as cording. Select 089. Slide the sewing threads to the left and insert three strands of cording into the slots of H cording foot with 5 cm (2˝) extending behind the foot. Knot together the strand ends. (The slots on H foot will hold the lengths of cording while stitches form over them.
Twin Needle Sewing As the name implies, the twin needle results in two identical parallel rows of stitches – utility or decorative. w The “Twin Needle” key should be pressed whenever using a twin needle. Be sure to test the stitch before sewing because twin needles are available in a variety of widths. The maximum stitch width available with the “Twin Needle” key activated is 3.0 and that maximum width is based on a standard 2 mm wide twin needle. Turn OFF the power switch and insert a twin needle.
Twin Needle Hem A twin needle hem is quick and easy. This is an excellent hemming method for knit fabrics because the bobbin thread zigzags, allowing the hem to stretch with the fabric. Be sure to use a stretch twin needle when sewing knit fabrics. Select 1. Press the “Twin Needle” key. Attach satin stitch foot F. Fold the hem up desired amount and topstitch with the twin needle. Carefully trim away excess fabric using sharp scissors.
Satin Stitches – Elongation Satin stitches 081 - 089 can be lengthened up to five times their original size without the stitch length varying. X1 X2 X3 X4 Select 087. Press “Elongation” key. (Each touch changes readout to next elongation.) X5 Place fabric and stabilizer under foot and sew. Press “Auto-Lock” key while sewing and machine will complete the design, lockstitch and automatically stop. Press “Auto Thread Cut” key.
SECTION VII Programming Combinations (Must have 3 Digit Mode Activated) Single Repeat with Memory Auto-Lock z z Select 081. Machine automatically converts to show selected stitch image and information after third digit is pressed. x x Press “Mirror Image” key. c c Press “Elongation” key. v v Press “Stitch Length” key and change stitch length to 0.30. b b Press “ENTER” key to memorize.
Combining a Sequence z Select 091. z (Press “Mirror Image” key and change stitch width or length if desired.) x x Press “ENTER” key to memorize. A blinking cursor will appear to indicate where next selected and entered stitch will be memorized within the sequence. c c Select 087. (Press “Elongation” key and change stitch width or length if desired.) v v Press “ENTER” key. b b Press “ENTER” key. n n Place fabric and stabilizer under foot and sew memorized sequence repeatedly.
n m n Change thread color. m Select 104. Press “ENTER” key. , , Press “Memory Auto-Lock” key. . ⁄0 . Place fabric and stabilizer under foot and sew over straight stitch, placing flower between leaves. ⁄0 Cut connecting threads. z Reset Combined Sequence to Beginning c It is possible to partially sew the combined sequence and restart the machine at the beginning. z Combine a sequence. v x Begin sewing. Stop sewing. x c Press “ENTER” key. v Reposition fabric and stabilizer under foot and sew.
Combining Letters There are 2 font styles: Block letters (300 stitch numbers) Script or Monogram letters (500 stitch numbers) z z Select 315. x x Press “ENTER” key. c c Select 348. v v Press “ENTER” key. b b Select 350. n n Press “ENTER” key. m m Select 337. , , Press “ENTER” key. . . Place fabric and stabilizer under foot and sew. Cut connecting threads. NOTE: Total capacity of one sequence is 50.
How to Preview the Combined Sequence (Utility, Satin, Decorative or Letters) Program the following stitches using the “ENTER” key: 519, 094, 523, 535, 315, 348, 350 and 337. q The LCD screen will show a maximum of 8 stitches at one time. The ARROW symbol q located under the sequence indicates that there are more stitches off screen in that direction. Press “Review Memory Left” key (or “Review Memory Right” key) to move cursor and preview the entire sequence.
Uniformly Adjusting Stitch Width or Length z If the cursor is positioned to the right of the last stitch in the programmed sequence, the stitch width or length adjustment is applied to the entire sequence. x Stitch Width: z Program 083, 094 and 083. (Cursor must be to the right of last stitch in sequence.) c x Press “–” on “Stitch Width/Needle Position” key. c Place fabric and stabilizer under foot and sew. All stitches within the sequence will have the same stitch width.
Individually Adjusting Stitch Width or Length z If the cursor is positioned under a stitch in the programmed sequence, the stitch width or length adjustment is applied only to that stitch. z Program 088 two times. x x Press “Review Memory Left” key to move cursor. c c Press “–” on “Stitch Width/Needle Position” key. v v Press “–” on “Stitch Length” key. b b Place fabric and stabilizer under foot and sew.
Permanent Memory It is possible to retain a sequence for future use even if the machine is turned off. Simply save the sequence in one of the four permanent memories. Each memory has a capacity of 50 stitches. z Saving Memory z Program 112 (Face to Face), 091 and 112. x x Press “M” key 1 time to activate Memory 1 (M1). c Press “ENTER” key to store. (An hourglass will briefly appear.) c NOTE: Activate Memory 2 (M2) by pressing “M” key 2 times. Activate Memory 3 (M3) by pressing “M” key 3 times.
Recalling Memory z z Press “M” key. x x Press “Mirror Image” key. (An hourglass will briefly appear.) Deleting an Individual Memory z z Press “M” key. x x Press “C” key to delete.
SECTION VIII q w w Taking Care of Your Machine Your machine has been meticulously designed and manufactured to give you a lifetime of sewing pleasure. Do not store the machine in a high humidity area, near a heat radiator or in direct sunlight. The machine is self-lubricating, however, the area around the bobbin and hook must be cleaned each time the machine has had extensive use. Do not dismantle the machine further than explained on these pages.
Replacing the Bobbin Case e Insert the bobbin case so the knob q fits next to the stopper w in the hook area. The red triangle marks e on the bobbin case and stopper must align with each other. w Attach the needle plate and tighten the screws. After cleaning, be sure to replace the needle, presser foot and bobbin. q Changing the Light Bulb Turn OFF the power switch. Unplug the machine. Wait until the bulb has cooled before touching it. Remove screw q. Pull away face plate w.
Stitch Chart NOTE: Stitches 001, 061, 062 and 063 have a number to the right of the stitch illustration. This number indicates how many stitches will be sewn if programmed into a sequence. Stitches that are compatible with the Face to Face key are identified on the stitch chart with an “F” directly following the stitch number. Buttonholes 010 and 071 are both the classic buttonhole style but are sewn using 2 different methods.
Optional Accessories Elna is pleased to offer the following optional accessories for your machine. This listing is current at time of printing but we are always developing new accessories to make sewing easier. Contact your authorized Elna dealer or service center to learn more about the latest innovations OR visit us at our website: www.elna.com.
Warning Messages Three beep sounds will alert you to machine problems. The LCD screen will show one of these messages. Message Reason What to Do Power switch is turned on while foot control is pressed. Release the foot control. Power switch is turned on with the needle in the down position. Press the “Up/Down Needle” key. Presser foot is up when sewing is attempted. Lower presser foot. While sewing, presser foot is raised. Lower presser foot.
Message Reason What to Do Machine will not sew with the Start/Stop key because the foot control is connected. Unplug the foot control. The Twin Needle Key has been pressed after selecting a stitch that is not compatible with a twin needle inserted. Select a different stitch or sew with a single needle. The Elongation Key has been pressed after selecting a stitch that cannot be elongated. Elongation can only be used with satin stitches 081 – 090.
TROUBLESHOOTING Condition Cause Needle thread breaks 1. 2. 3. 4. 5. See page(s) The needle is not threaded properly. The needle thread tension is too tight. The needle is bent or blunt. The needle is not inserted correctly. The needle thread and bobbin thread are not properly under (drawn to the back of) the presser foot when starting to sew. 6. The fabric is not moved to the back when sewing is finished. 7. The thread is either too heavy or too fine for the needle. 8.
INDEX F Fabric ........................................................................... 20 Face Plate ................................................................ 3, 83 Face to Face Key ..................................................... 2, 72 Factory Default Settings ........................... 12, 15, 31, 32 Fagoting ....................................................................... 64 Feed Dog ........................................................... 3, 16, 82 Filigree Hemstitch .........
Scallop Edges .............................................................. 68 Script Letters ......................................................... 76, 84 Seam Allowance Lines ................................................ 17 Select Mode Key .................................................... 11, 29 Sensor Buttonholes ............................................... 42-45 Serpentine Stitch ......................................................... 39 Shank .............................................
