IMPORTANT SAFETY INSTRUCTIONS Your Elna 6600 sewing machine is designed and constructed for HOUSEHOLD use only. Read all instructions before using this machine. DANGER – To reduce the risk of electric shock: 1. Your sewing machine should never be left unattended when plugged in. Always unplug the machine from the electrical outlet immediately after using and before cleaning. 2. Always unplug before replacing light bulb. Replace bulb with same type rated 12 Volts, 5 watts. 3.
TABLE OF CONTENTS Saddle Stitch ....................................................................................... 57 Stretch Seam ....................................................................................... 57 Overlock Stitch .................................................................................... 58 Double Overlock Stitch ........................................................................ 58 SECTION I – Machine Parts and Functions Part Names ..............................
SECTION I - Machine Parts and Functions Part Names 1 27 2 28 3 26 4 25 5 24 6 7 23 8 22 21 9 20 11 12 13 14 19 18 17 10 16 START STOP 15 29 30 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28.
Standard Accessories 5 4 3 2 Top Cover (Lift up and back) 1. 2. 3. 4. 5. 6. 6 1 Seam ripper Set of needles Quilt guide B: Buttonhole foot (4-step) Scant 1/4 inch foot Bobbins (8 + 1 in machine = 9 total) Side Cover 15 (Pull down Side Cover to open) 7 14 13 A 12 C D E F 7. 8. 9. 10. 11. 12. 13. 14. 15.
Machine Box 26 25 27 25. 26. 27. 28. 29. 28 Instruction book Power supply cord Foot control Knee lifter Carrying bag 29 Presser Foot and Accessory Definitions A: Standard Metal Foot This foot comes attached to your machine. It is mainly used for straight stitches and zigzag stitches longer than 1.0. The button locks the foot in a horizontal position helping to sew over multiple layered seams. B: Buttonhole Foot Sew oversized buttonholes for novelty buttons or a decorative accent.
F: Satin Stitch Foot The cutout on the underside of the foot is designed to accommodate dense stitch formation. Ideal when sewing satin and decorative stitches. G: Blind Hem Foot The guide on the foot helps ensure that the needle catches only one or two fibers of the hem, resulting in an invisible hemline. H: Multi-Cord Foot Design your own braids or trims. Place one to three cords in the foot and sew over cord(s) for a simple couching method.
Extension Table and Free Arm Extension Table The extension table provides more sewing space to make sewing easier. The extension table can be easily removed for free arm sewing. To Remove: Pull the end of the extension table away from the machine, as shown. To Attach: Push the table back into place to reattach the extension table. Free Arm Free arm sewing is good for circle areas like sleeves, waistbands and pant legs. If socks, knee or elbow areas need mending, the free arm will be best to use.
Knee Lifter The knee lifter allows you to raise or lower the presser foot without using your hands. This is especially beneficial when pivoting corners or sewing patchwork pieces. Insert knee lifter aligning the slots with the notches. The presser foot rises equal to the amount of pressure applied to the knee lifter. Stop sewing before moving the knee lifter to the right to raise the presser foot. Release the knee lifter to lower the presser foot.
Connecting Machine To Power Supply q Before connecting the power cord, make sure the voltage and frequency shown on the machine are identical to your electrical power. To connect machine to power supply, turn off the power switch q. Insert the foot control plug w and machine plug e into the machine and the power supply plug r into the wall socket. e Your machine may come equipped with a polarized plug (one prong wider than the other). A polarized plug reduces the risk of electrical shock.
Main Function of Keys 1. START/STOP Key Press this key to start the machine. The first few stitches will be sewn at a slow speed and then machine sews at the speed set by the speed control lever. Press key again to stop machine. Press and continue to hold key to sew at slow speed, release key to sew at set speed. Press key again to stop. NOTE: The foot control must be detached to use this key. 2.
Keyboard Selection Keys 1 3 2 16 5 4 6 7 8 9 15 10 11 12 13 14 1. AUTO tension LED The “AUTO” LED indicates the needle thread tension setting. AUTO Green Light – Needle thread tension is set on “AUTO” No Light – Needle thread tension is manually set between 0 and 9. Flashing Light – Selected stitch requires a manual setting. 2. LCD Screen Brightness Control Lighten or darken the screen with this dial. 3. Stitch Width and Needle Position Key Press “–” or “+” side of key to change setting.
7. Select Mode Key When you switch on the machine, the Direct Select Mode is active. You can select the first ten stitches (illustrated on the keyboard) with a single touch of the key. Touch the “MODE” key to activate the 3 Digit Mode. You can select all stitches by entering the 3 digits for the desired stitch. Touch “MODE” key again to reactivate the Direct Select Mode. 8. Memory Save/Recall Key The 3 Digit Mode has three separate memories for saving a sequence of stitches.
15. Stitch Selection Keys You can select a stitch in the Direct Select Mode by pressing the key that is illustrated with the desired stitch. To select stitches in the 3 Digit Mode, simply press the three digits for the desired stitch. To cancel the stitch you selected, press the “C” key or select a different stitch. + + 16. Symbols in the LCD Screen q Selected stitch. q w Recommended setting for needle thread tension y dial. (If the dial is not set on “AUTO”, a numerical value is shown.
Setting Quick Resumption, Sound and Language Modes These three modes/functions can be set according to your preferences. Each new setting requires you to turn OFF the power switch. Turn ON the power switch while pressing “ENTER” key. Message screen appears. Press “1” key to change quick resumption or “2” key to change sound or “3” key to change language. Quick Resumption – The last stitch or memorized sequence of stitches that were sewn will appear when machine is switched on. Press “1” key.
Reset to Factory Default It is possible to reset the machine to the factory defaults with English language as default. Turn OFF the power switch. Press “ENTER” key while turning power switch ON. Message screen appears. Press “0” key. Message screen appears. Press “ENTER” key to confirm and reset to factory default. OR Turn off power switch to cancel the reset. Controlling Sewing Speed Sewing speed can be varied with the foot control. The harder you press on the foot control, the faster the machine runs.
How To Drop the Feed Dog w The feed dog can be dropped out of position for special sewing techniques: free motion embroidery, stippling, button sewing, etc. q The feed dog must always be up for regular sewing. Locate the feed dog lever on the back of the free arm. Slide the lever either to the right (down) q or to the left (up) w. To bring up the feed dog, hand turn the flywheel after sliding lever to the left. Presser Foot Lever Raise and lower the foot with this lever q.
Attaching and Removing Presser Feet Press the “Up/Down Needle” key until the needle is in the raised position. Turn OFF the power switch. Raise the presser foot and press the red button q on back of the shank. The presser foot will drop off. e w q Place the selected presser foot so the pin e on the foot lies just under the groove w of the shank. Lower the presser bar and attach the foot. Attaching and Removing Shank q Turn OFF the power switch. Raise the presser bar.
Adjusting the Needle Thread Tension q Choosing the Correct Tension - Straight Stitch The ideal straight stitch will have threads locked between the two layers of fabric, as shown left (magnified to show detail). The “AUTO” setting on the needle thread tension dial should be aligned with the setting mark q. A green light will appear. If you look at the needle thread w (top thread) and bobbin thread e (bottom thread), you will notice that there are no gaps. Each stitch is smooth and even.
Using the Fine Adjustment Screw Choice of fabrics and threads may affect the stitch formation. The fine adjustment screw can be used to either lengthen or shorten the stitch. q Fine adjustment screw w Standard mark e Setting mark q w e To fine tune, use a screwdriver to move the setting mark. t r • If stitches are too short r, correct by turning the screw in the direction of “+”. • If stitches are too long t, correct by turning the screw in the direction of “–”.
SECTION II - Getting Ready to Sew Weight Fabric Needle Type Very Light Chiffon, Fine Lace, Organdy Universal Ball Point 9 (65) 9 (65) Light Batiste, Lawn, Crepe de Chine, Challis, Handkerchief Linen, Crepe, Taffeta, Satin Stretch 11 (75) Universal 11 (75) 12 (80) Single Knits, Jersey, Swimwear, Tricot Stretch Ball Point 11 (75) 11 (75) Leather, Suede Leather 11 (75) Flannel, Velour, Velvet, Velveteen, Corduroy, Linen, Gabardine, Wool, Terry, Burlap Universal 14 (90) Double Knits, Stret
Needle Definitions The illustration identifies the main parts of a sewing machine needle. q q w e r t y Body Shaft Long groove (round side of needle) Short groove (flat side of needle) Eye Point w Universal – an all-purpose needle that handles most woven and knit fabrics. e Ball point – the point spreads the fibers, preventing tears and is especially suited for loose knits and interlock knits. Not recommended for embroidery.
Winding a Bobbin To remove bobbin, slide bobbin cover plate release button q to the right and lift away the bobbin cover plate w. q Lift out the bobbin e. e Turn ON the power switch. w q Lift up the spool pin. Place the spool of thread on the spool pin with the thread coming off the spool as shown. Attach the spool holder and press it firmly against the spool of thread. q NOTE: Spool holder needs to be changed according to the type of thread spool A A. Large spool B.
t t Push bobbin winder spindle to the right. The computer display screen will show a bobbin winding message. y y Holding the free end of the thread, press the foot control or Start/Stop key. Stop machine after the bobbin has made a few turns. Cut the thread tail close to the hole in the bobbin. Start machine again to continue winding bobbin. When the bobbin is fully wound, stop the machine. u u Move the spindle to the left to return the bobbin winder to its original position. Cut the thread as shown.
Inserting the Bobbin Place the bobbin in the bobbin case with the thread running counterclockwise. Guide the thread into notch A on the front side of the bobbin case. Hold the bobbin with your right hand and pull the thread to the left, through the tension spring blades. A Continue pulling the thread lightly until the thread slips into notch B . Pull out about 15 cm (6˝) of thread. B Replace the bobbin cover plate. Refer to the chart shown on the bobbin cover plate to check the threading.
Threading the Machine r w Raise the presser foot. Press the “Up/Down Needle” key q until the needle is in an up position. q e t y w Pull the thread under the hook and around upper thread guide w. Guide the thread down right channel and around the checkspring holder e. e Firmly pull the thread from right to left, over the take-up lever and down into the take-up lever eye r. r Proceed down left channel and through the lower thread guide t.
Built-in Needle Threader Press the “Up/Down Needle” key q until the needle is in an up position. Turn OFF the power switch. Lower the presser foot. q START STOP Lower the needle threader lever w as far as it will go. Hook e is automatically inserted into the needle eye. w e Bring the thread around guide r and under hook e. e r Slowly release the lever while holding the thread end and let the needle threader return to its original position. A loop of thread t is pulled through the needle eye.
Drawing Up the Bobbin Thread Turn ON the power switch. Raise the presser foot and hold the needle thread lightly with your left hand. Press the “Up/Down Needle” key q twice to pick up the bobbin thread. q Draw up the needle thread together with a loop of bobbin thread. Slide 10 cm (4˝) of both threads to the back under the presser foot.
SECTION III - Basic Sewing How to Select a Stitch q q Select stitches 1 - 0 in Direct Mode by touching the corresponding key. w Select stitches in the 3 Digit Mode by pressing w + + “MODE” key and then the 3 corresponding keys. + Set-up your machine according to the LCD screen. See page 13. Straight Stitch When the machine is turned on, it is automatically set to sew a straight stitch in the center needle position (Exception: Quick Resumption Mode. See page 14).
Cutting the Threads Raise the presser foot. Remove the fabric; pull the threads to the back and cut threads using the thread cutter. (The threads are cut the proper length to start the next seam.) Changing Sewing Direction Stop the machine and press the “Up/Down Needle” key to bring the needle down into the fabric. Raise the presser foot using either the presser foot lever or knee lifter. Pivot the fabric around the needle to change sewing direction. Lower the presser foot.
Adjusting Stitch Length When you press the “Stitch Length” key, the stitch length can be set at 0.00 or between 1.0 and 5.0. Press the top “–” side of the key to shorten the stitch length. Press the bottom “+” side of the key to lengthen the stitch length. 1.0 2.2 5.0 Programming My Personal Settings All stitches in the Direct Select Mode (1 to 0) can be programmed to override the factory default settings. q q Change stitch length to 2.6. w w Press “My Personal Setting” key. Message Screen Appears.
Reset Stitch To Factory Default Settings. q It is possible to reset the machine so personal settings for an individual stitch revert to the factory default settings. q Display the stitch you want to reset in the LCD screen. w Press “My Personal Setting” key. Message screen w appears. e e Press “C” key. PS symbol disappears and factory default settings are displayed. Reset All Stitches To Factory Default Settings.
Sewing On Heavy Fabrics The black button on presser foot “A” locks the foot in a horizontal position when pushed in before lowering the presser foot. This ensures even feeding at the beginning of seams and helps when sewing many layers of fabric such as welt seams used to hem jeans. When the point of an increased thickness is reached, lower the needle and raise the presser foot. Press in the black button. Lower the foot and continue sewing.
Zipper Insertion Lapped Application Lapped zippers are usually inserted into a side seam of skirts or pants, for example. Use zipper foot E instead of standard metal foot A. Attach the pin on zipper foot E to the groove on the shank. • To sew the left side of the zipper, attach the zipper foot on the right-hand side. • To sew the right side of the zipper, attach the zipper foot on the left-hand side. Fabric Preparation Add 1 cm (3/8˝) to the zipper size.
Close zipper. Turn zipper face up (right seam allowance forms a small fold at basting line) and smooth zipper teeth away from seam. Attach foot with right side pin. Reset straight stitch length to 2.5. Starting at the bottom, sew through the folded seam allowance and zipper tape. Stop just before the zipper foot reaches the slider on the zipper tape. Lower the needle slightly into the fabric. Raise the zipper foot and open the zipper. Lower the foot and stitch the remainder of the seam.
Rolled Hem An easy, professional way to sew hems. The spiral on the hemmer foot guides the fabric edge to create a rolled hem. Recommended for fine, sheer fabrics used in bridal wear. Attach hemmer foot D. Trim about 6.5 mm (1/4˝) from corners to reduce bulk. Make a double 3 mm (1/8˝) fold approximately 8 cm (3˝) in length. Align fabric hem edge with the inside of right extension of foot q. Use this placement on foot as guide. Lower presser foot. Sew 3 or 4 stitches while holding needle and bobbin threads.
Zigzag Stitch The zigzag stitch is a very versatile stitch. Simply change its width and length. Use the zigzag to finish raw seam edges, sew narrow hems, sew satin stitch appliques and create beautiful monograms. Select 2. Adjusting Stitch Width and Length Press the “–” or “+” side of the keys to change the stitch width and length.
Satin Stitch Appliqué The zigzag stitch is commonly used for appliqué, monogramming, stems of flowers and petals. (A short zigzag stitch length creates the satin stitch.) Threads of 100% cotton, rayon or silk provide the best results. • Apply stabilizer to the fabric for the stitch to form correctly. Select 2. Attach satin stitch foot F. Decrease stitch width to 3.5 and stitch length to 0.40. Appliqué Preparation 1. Press fusible webbing to the wrong side of a lightweight fabric. 2. Cut out design shape.
Mending a Tear Pull torn edges together and fuse a piece of interfacing slightly larger than the tear to the wrong side of the garment. Decrease stitch length to 0.20 – 0.50. Begin sewing above the tear. Stitch down the middle, pulling edges together. Stop sewing just beyond end of tear. Depending on the tear, you might need to stitch area 2 or 3 times. Apply 7 mm (1/4˝) Elastic Attach satin stitch foot F. Increase stitch length to 2.5 or higher. 1. Mark elastic and fabric into equal parts. 2.
Blind Hem Stitches The stretch blind hem (4) is a great method for finishing a hemline or sleeve. Use the woven blind hem (026) on non-stretch fabrics. Finish the raw hem edge with a zigzag or 3 step zigzag q before sewing the blind hem. Select 4 or press “MODE” key and select 026. Fold up the hem allowance and press. Fold under the hem toward right side of garment. Leave a 6.5-10 mm (1/4˝ to 3/8˝) extension e at the right. e w Wrong side of fabric.
Triple Seam This strong, durable stitch is recommended where both elasticity and strength are needed. Because of its durability, once in place, this stitch is not easily removed. Use it to reinforce areas such as crotch and armhole seams or to construct items such as backpacks. This stitch can also be used for topstitching. Elna invented this stitch in 1952. Select 6. Using a straight stitch (stitch length 4.0), baste a seam together. Verify the fit. Reset the machine for triple seam and sew.
Buttonhole Variations All buttonholes should use interfacing that is the same weight as the fabric. Interfacing is especially important when sewing on stretch fabrics. 9 or 019 0 Classic Buttonhole (Sensor or 4 Step Memory) The most common buttonhole, found on blouses, shirts, pants, etc. It consists of a bartack at each end and a compact zigzag stitch along each side. Classic Keyhole Buttonhole Accommodates the shank found on large buttons used on heavy coats and jackets.
Test sew the buttonhole on a sample swatch of the same fabric. Include the interfacing and any seam allowances that will be in the actual garment. This is very important to ensure the buttonhole style and fabric are compatible. Sensor Buttonholes (Totally Automated Buttonholes) 011 012 013 Select a buttonhole style - 9 through 018. 014 015 016 017 018 The LCD screen will briefly show an illustration advising that the buttonhole lever be lowered.
Mark the buttonhole area on the fabric. Place both threads to the left under the foot. Insert the garment under the foot and hand turn the flywheel to lower the needle at the starting point. Then lower the buttonhole foot. Begin sewing. While sewing a buttonhole, the LCD screen shows which portion is currently being sewn.
Press “MODE” key to access 3 Digit Mode for Buttonholes 011 - 018.
016 Heirloom Buttonhole w q e The buttonhole will automatically sew: q the front bartack, zigzag backwards on left side w straight stitch forward on right side to front bartack and zigzag backwards on right side e back bartack and stop 017 Faux Chain Buttonhole q w The buttonhole will automatically sew: q the front bartack, and stitch backwards on left side w back bartack, stitch forward on right side to front bartack and stop q 018 Bound Buttonhole (Increase stitch length so it is appropriate f
Cutting Open Buttonhole Place a pin just inside the bartack at each end to prevent accidentally cutting bartacks. Cut buttonhole open with the seam ripper. Troubleshooting Tips If the button is extremely thick and difficult to fit through the test buttonhole, you can lengthen the buttonhole by pulling the buttonholder on the foot back a little extra. The length of the hole will increase by that same amount. q Make sure there is not a gap between the slider and the spring holder.
Corded Buttonhole Corded buttonholes are found on coats and other garments that require extra strong buttonholes. The cording reinforces and accentuates the buttonhole. Sew a corded buttonhole using the same procedure as described for a classic buttonhole. • Set the stitch width to match the thickness of the cording. w With the buttonhole foot raised, hook the filler cord q on the spur w at the back of the buttonhole foot. Bring the ends forward under the buttonhole foot.
4-Step Memory Buttonholes – Classic and Bound 019 Classic Buttonhole (4 Step Memory) This buttonhole is especially suited for oversized novelty buttons or larger decorative openings. All buttonholes should use interfacing suitable for the fabric weight. Test sew buttonhole on sample swatch. Select 019. The LCD screen will briefly show two messages. Use either the R or B buttonhole foot. If you use the R foot, fully extend open the buttonholder q (maximum buttonhole size with this foot is 3.2 cm or 1 1/4˝).
Start sewing – front bartack, lockstitch. Machine will automatically stop when buttonhole is completed. Sewing Additional Buttonholes To sew another buttonhole the same size - raise foot, move fabric, lower foot and sew. Reset Buttonhole Size To sew a buttonhole a different size (or to adjust stitch length), reset the machine by pressing “ENTER” key or reselect buttonhole. Sew new buttonhole size using same method.
020 Bound Buttonhole (4 Step Memory) Great for oversized buttons requiring tailored buttonholes, welt pockets or larger decorative openings. All buttonholes should use interfacing suitable for the fabric weight. Select 020. The LCD screen will briefly show two messages. Increase stitch length so it is appropriate for your fabric weight. Test sew the buttonhole on sample swatch. Attach buttonhole foot B. (You could use the R buttonhole foot. If you use R foot, fully extend the buttonholder open.
8. 8. Start sewing – straight stitch front edge, lockstitch. Machine will automatically stop when buttonhole is completed. 9. 9. Cut down center of sewn rectangle, snipping into each corner. 10. 10. Pass the bias square through slit and pull to wrong side of garment to form the lips of buttonhole. 11. 11. From wrong side, press lips into center and fold bias fabric over lips forming a tuck at each end. 12. 12. From right side, align lips. Baste and press. 13. 13.
How To Sew On a Button Hand sewing buttons to a garment is very timeconsuming. Sew them on in one quick, easy step. Select 021. The LCD screen will briefly show a message. Drop the feed dog. See page 16. • Set the stitch width according to the position of the holes in the button. Mark button placement on fabric. Use washable glue or transparent tape to temporarily secure the button. Place the button and fabric under the presser foot. Match the holes in the button to the horizontal slot on the presser foot.
Darning Darning with a sewing machine saves a lot of time. It is used for repairing very worn areas (not holes) in fabric. Select 022. The LCD screen will briefly show two messages. Automatic Darning Extend the buttonholder q completely open. Place both threads to the left under the foot. Insert fabric under the foot and lower the needle at the starting point w. Lower the foot. Sew. e The size of one darning cycle is variable.
Bartacks A bartack is a reinforced stitch used on garment areas that receive extra stress like pockets, belt loops and zippers. Select 023. The LCD screen will briefly show a message. Automatic Bartack Place the fabric under presser foot. Lower presser foot. Sew until the machine automatically stops. A 1.5 cm (5/8˝) bartack is sewn. Press the “Stitch Width/Needle Position” or “Stitch Length” key to adjust bartack and density. Make a longer bartack by combining bartacks until desired length is obtained.
Arrowtack This stitch is used to reinforce the corners of pockets and pleats. Select 024. Place fabric under foot so center pleat line is horizontal in front of you. Lower presser foot so the center bar lines up with the pleat line. (This allows the widest part of the stitch to be sewn in the pleat center.) Begin sewing and press “Auto-lock” key. Machine will complete arrowtack, lockstitch and automatically stop.
Basting Stitch The basting stitch can be used to temporarily hold together two or more layers of fabric. Use a fine needle to avoid leaving permanent needle marks. Select 030. Lower the feed dog. Set foot pressure dial to 2 or 1. Loosen needle tension to 3. The LCD screen will briefly show a message. How To Attach Open Toe Embroidery/Darning Foot w Raise the needle and presser foot. Turn OFF power switch. Loosen set screw q and remove shank.
Saddle Stitch Wonderful as a lovely topstitch effect for suits, blazers, jumpers, jeans and linen napkins. Because of its configuration, once in place, this stitch is not easily removed. Select 031. Use edge of foot as guide for fabric edge. Press “Stitch Width/Needle Position” key to move needle position and set distance topstitching will be from fabric edge. Lower the presser foot and sew. Stretch Seam A narrow stretch stitch that eliminates puckering on knit fabrics and bias seams.
Overlock Stitch Create a straight seam and overcast at the same time. Select 033. Sew seam. Trim away any excess seam allowance. Double Overlock Stitch This stitch finishes the edges of your seams similar to a commercial overlock machine stitch. Elna invented this stitch in 1976. Select 034. Place the fabric edges together under the presser foot. Trim away any excess seam allowance.
SECTION IV - Quilting Piecing Fabrics Together Accuracy is the key when sewing together fabric pieces for a quilt. Be sure to precisely cut your fabric pieces with 6.5 cm (1/4˝) seam allowances. Select 1. Attach scant 1/4˝ foot. The black bar on the foot is a perfect 1/4˝ seam guide from center needle position (3.5). Place fabric edges (right sides together) under foot against the black guide q and sew a perfect 1/4˝ seam. OR Use 4.5 needle position for a scant 1/4˝ seam.
Open Toe Walking Foot Great for keeping quilt layers from shifting when sewing. How To Attach Open Toe Walking Foot Press the “Up/Down Needle” key until the needle is in an up position. Raise the presser foot. Turn OFF power switch. Loosen thumbscrew and remove shank. Place the walking foot on the presser bar with the lever over the needle clamp screw; tighten thumbscrew. Turn ON power switch. Select 1. Set stitch length 2.5 – 3.5. Set foot pressure dial between 2 and 3.
Buttonhole Appliqué A favorite method of applying small pieces of fabric to quilts for decoration. Select 079, 080, 081 or 082. Use fine embroidery thread (50 weight or finer) and needle appropriate to fabric. You may need to set the foot pressure dial to 2. q q In this type of appliqué, raw edges are folded under. To prepare raw edge, first cut appliqué design out of paper. w w Press fusible webbing to wrong side of appliqué fabric. e Cut the fabric slightly larger than paper pattern.
Free Motion Quilting or Stippling Add dimension to your quilt by stitching down the surrounding background fabric around larger designs, like hearts or flowers. Lower the feed dog and sew fabric layers in a random pattern without the stitching lines crossing each other. The more compact the stitching, the more the background will flatten and make surrounded designs stand out. This is a technique commonly referred to as stippling. Select 1. Attach open toe embroidery/darning foot P-2. See page 56.
SECTION V - Decorative Sewing Scallop Edges Attractively finish edges of collars, pockets and placemats. Select 035, 036, 038 or 039. To edge a collar, place interfacing/stabilizer between upper and under collar and sew scallop on seam line. After sewing, trim fabric close to stitching taking care not to cut scallops. Corded Trim Sew over three strands of cording to create unique borders and trims. Pearl cotton, knitting yarn, embroidery floss, lace thread, fine wool or lily yarn may be used as cording.
Twin Needle Sewing As the name implies, the twin needle results in two identical parallel rows of stitches – utility or decorative. The “Twin Needle” key should be pressed whenever using a twin needle. Be sure to test the stitch before sewing because twin needles are available in a variety of widths. The maximum stitch width available with the “Twin Needle” key activated is 3.0 and that maximum width is based on a standard 2 mm wide twin needle. e q Turn OFF the power switch and insert a twin needle.
Twin Needle Decorative Stitches Why not try two different thread colors in the needles? Select a decorative stitch. “Twin Needle” key should still be selected. Hand turn flywheel to test if needles hit the foot. Place fabric and stabilizer under foot and sew. After completing twin needle sewing, turn OFF the power switch. Remove twin needle. Set up machine for single needle sewing. NOTE: If a stitch is not compatible with a twin needle, a warning message will appear in the LCD screen.
Circle Sewing The circular sewing pivot pin is inserted into the extension table and provides a pivot point to sew perfect curves or circles for doilies or large scallops. Use either utility or decorative stitches. Select a decorative stitch. Fold fabric into quarters to determine center. Pierce center of fabric with pivot pin. Insert pivot pin into hole on the extension table. Lower presser foot and sew. Smooth the fabric out evenly from the center to the front of the foot by hand.
SECTION VI - Programming Combinations (Must have 3 Digit Mode Activated) Single Repeat with Lockstitch q q Select 035. (Machine automatically converts to show selected stitch image and information after third digit is pressed.) w w Press “Mirror Image” key. e e Press “Elongation” key. r r Press “Stitch Length” key and change stitch length to 0.30. t Press “ENTER” key to memorize.
Combining a Sequence q q Select 177. (Press “Mirror Image” key and change stitch width or length if desired.) w Press “ENTER” key to memorize. A blinking cursor w will appear to indicate where next selected and entered stitch will be memorized within the sequence. e Select 045. e (Press “Elongation” key and change stitch width or length if desired.) r r Press “ENTER” key. t t Press “ENTER” key. y y Place fabric and stabilizer under foot and sew memorized sequence repeatedly.
y u y Change thread color. u Select 102. Press “ENTER” key. i i Select 200. Press “ENTER” key. o !0 o Place fabric and stabilizer under foot and sew over straight stitch, placing flower between leaves. !0 Cut connecting threads. Reset Combined Sequence to Beginning q It is possible to partially sew the combined sequence and restart the machine at the beginning. e q Combine a sequence. w Begin sewing. Stop sewing. r e Press “ENTER” key. Reposition fabric.
Combining Letters There are 3 font styles: Block letters (300 stitch numbers) Gothic letters (400 stitch numbers) Script or Monogram letters (500 stitch numbers) q q Select 315. w w Press “ENTER” key. e e Select 348. r r Press “ENTER” key. t t Select 350. y y Press “ENTER” key. u u Select 337. i i Press “ENTER” key. o Place fabric and stabilizer under foot and sew. Cut connecting threads when using Block and Script letters. Do NOT cut connecting threads when using Gothic letters.
How to Preview the Combined Sequence (Utility, Satin, Decorative or Letters) Program the following stitches using the “ENTER” key: 519, 178, 367, 423, 435, 315, 348, 350 and 337. The LCD screen will show a maximum of 8 stitches at one time. The ARROW symbol q located under the sequence indicates that there are more stitches off screen in that direction. Press “Review Memory Left” key (or “Review Memory Right” key) to move blinking cursor and preview the entire sequence.
Individually Adjusting Stitch Width or Length If the cursor is positioned under a stitch in the programmed sequence, the stitch width or length adjustment is applied only to that stitch. q q Program 046 two times. w w Press “Review Memory Left” key to move cursor. e e Press “–” on “Stitch Width/Needle Position” key. r r Press “–” on “Stitch Length” key. t t Place fabric and stabilizer under foot and sew.
Permanent Memory q It is possible to retain a sequence for future use even if the machine is turned off. Simply save the sequence in one of the three permanent memories. Each memory has a capacity of 50 stitches. Saving Memory w q Program 130, 177 and 129. w Press “M” key 1 time to activate Memory 1 (M1). e e Press “ENTER” key to store. (An hourglass will briefly appear.) NOTE: Activate Memory 2 (M2) by pressing “M” key 2 times. Activate Memory 3 (M3) by pressing “M” key 3 times.
Recalling Memory q q Press “M” key. w w Press “Mirror Image” key. Deleting an Individual Memory q q Press “M” key. w w Press “C” key to delete. (An hourglass will briefly appear.
SECTION VII - Heirloom Pintucks A beautiful accent to any project. Pintucks should be added to your fabric before cutting out the pattern piece. Select 1. Attach blind hem foot G. Use a washable marker to draw parallel lines for pintucks on fabric right side. Fold fabric on first line with wrong sides together. Place folded edge against guide on foot. Decide how wide you want the pintucks and move the thumb nut q to move the guide. Sew pintuck. Sew remaining pintucks using same method.
Hemstitches Hemstitching, also known as French hand sewing, was traditionally only a hand sewn art. There are several stitches to choose from that will add an “old world charm”. Best results require the use of linen, cotton or a blend of linen/cotton. Thread machine, needle and bobbin with a fine cotton embroidery thread (50 weight or finer). Insert a universal needle size #100, #110 or a wing needle (see cautions below). Use spray starch and press to stabilize fabric.
Fringing Fringing adds a special touch on table linens and shawls. Choose a firm, woven fabric like linen where threads can be removed easily. Select 064 (Mirror Image) or 080. q Carefully cut the fabric on grain. Remove a single yarn or thread where the fringing is to begin. w Sew down the left side so the right hand stitches fall in the open space. e Remove all excess yarn located to the right of stitching and create fringe. Drawn Work Drawn work uses the same method as fringing.
Smocking Smocking is a delicate, decorative treatment on children’s clothing or women’s blouses. Choose a soft, lightweight fabric such as batiste, gingham or challis. Cut the fabric three times the finished width. Select 1. Increase stitch length to 5.0. Sew rows of straight stitches about 10-13 mm (3/8˝-1/2˝) apart, across the area to be smocked. (A looser needle thread tension will make gathering easier.) 10 ~ 13 mm Tie the threads along one edge.
SECTION VIII - Taking Care of Your Machine Your machine has been meticulously designed and manufactured to give you a lifetime of sewing pleasure. Do not store the machine in a high humidity area, near a heat radiator or in direct sunlight. The machine is selflubricating, however, the area around the bobbin and hook must be cleaned each time the machine has had extensive use. Do not dismantle the machine further than explained on these pages. Clean the outside of the machine with a soft cloth and pure soap.
e Clean the feed dog and hook area with the lint brush. e Wipe out gently with soft, dry cloth. (You can also use a small vacuum cleaner.) Replacing the Bobbin Case r z r Insert the bobbin case so the knob fits next to the stopper in the hook area. z Stopper x Knob t Replace the needle plate, inserting the two needle t plate guide pins into the holes in the needle plate. Replace the screw. x After cleaning, be sure to replace the needle, presser foot and bobbin.
Stitch Chart 001 002 003 004 005 006 007 008 009 010 SEN 3 011 012 013 014 015 016 017 018 019 020 SEN SEN AUTO AUTO 1 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115
Block Letters 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 5 SPACE SPACE Gothic Letters 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 Script Letters 501 502 503 504
Optional Accessories Elna is pleased to offer the following optional accessories for your machine. This listing is current at time of printing but we are always developing new accessories to make sewing easier. Contact your authorized Elna dealer or service center to learn more about the latest innovations OR visit us at our website: www.elna.com.
Warning Messages Three beep sounds will alert you to machine problems. The LCD screen will show one of these messages. Message Reason Power switch is turned on while foot control is pressed. What to Do Release the foot control. Presser foot is up when sewing is attempted. While sewing, presser foot is raised. Lower presser foot. The machine was stopped before lockstitch was completed. Start machine and allow lockstitch to complete.
Message Reason The Elongation Key has been pressed after selecting a stitch that cannot be elongated. What to Do Select a satin stitch (035050). Machine stops because thread is tangled in take up lever or bobbin area. Turn off power switch. Remove tangled thread from take up lever and bobbin area. Wait 15 seconds before restarting. Bobbin winder spindle locks during bobbin winding. Turn off power switch. Remove tangled thread. The machine is malfunctioning because of the item indicated.
TROUBLESHOOTING Condition Needle thread breaks Cause 1. 2. 3. 4. 5. The needle is not threaded correctly. The needle thread tension is too tight. The needle is bent or blunt. The needle is not inserted correctly. The needle thread and bobbin thread are not correctly under (drawn to the back of) the presser foot when starting to sew. 6. The fabric is not moved to the back when sewing is finished. 7. The thread is either too heavy or too fine for the needle. Bobbin thread breaks 1.
INDEX A Accessories .................................................................... 4-5, 83 Accessory Storage .............................................................. 3, 4 Add Stitches ............................................................................ 71 Alignment of Stitches Within a Sequence .............................. 72 Appliqué ........................................................................... 37, 61 Arrowtack ............................................................
Mending a Tear ....................................................................... 38 Mesh Hemstitch ...................................................................... 76 Mirror Image Key ............................................................. 12, 65 Mode Key ................................................................... 12, 28, 67 Monograms ...................................................................... 70, 82 My Personal Setting Key ............................................
