INSTRUCTION MANUAL VISUAL PRESENTER ＭＯ-１ Please read this instruction manual carefully before using this product and keep it for future reference
IMPORTANT SAFEGUARDS ■ Read Instructions All the safety and operating instructions should be read before the appliance is operated. ■ Retain Instructions The safety and operating instructions should be retained for future reference. ■ Heed Warnings All warnings on the product and in the operating instructions should be adhered to. ■ Follow Instructions All operating and use instructions should be followed. ■ Cleaning Unplug this product from the wall outlet before cleaning.
■ Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
■ Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: • When the power-supply cord or plug is damaged. • If liquid has been spilled, or objects have fallen into the product. • If the product has been exposed to rain or water. • If the product does not operate normally by following the operating instructions.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of SA 1965 sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance SA 1966 (servicing) instructions in the literature accompanying the product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER MAY BE REQUIRED TO TAKE ADEQUATE MEASURES. FOR UNITED STATES USERS: INFORMATION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
BEFORE YOU USE ■ The supplied power cord and AC adapter are designed for exclusive use with this product. Do not use them with other equipments. ■ Be sure to use the power cord applicable to your local power specifications. If the product was sold in Japan, use the AC adapter sold with the product with 100VAC and 50 or 60 Hz. ■ Do not knot or coil the power cord or AC adapter cord or wrap them around the AC adapter. Doing so may damage the cords, causing fire or electric shock.
■ Depending on the type of SD card being used, it may not be used with the product. ■ Transfer the data from the SD card onto a device such as a PC to save a backup copy. Malfunction of the product or repairs to it may cause the data saved in the SD card to be deleted.
CONTENTS IMPORTANT SAFEGUARDS............................................................................................. 2 BEFORE YOU USE ........................................................................................................... 7 １ BUNDLED ITEMS ........................................................................................................ 11 ２ PART NAMES AND FUNCTIONS ................................................................................12 Appearance .................
7 USING AN SD CARD ...................................................................................................35 Saving images ...............................................................................................................36 Displaying the saved data ..............................................................................................36 Thumbnail display mode ................................................................................................
１ BUNDLED ITEMS Product's package has the following contents. Contact your dealer if any of the following items are not included in the package you purchased.
２ PART NAMES AND FUNCTIONS Appearance Operation of the main unit: P22 ① ④ ⑤ ⑦ ② ③ ⑧ ⑥ Name ① Camera head ② Arm ③ Operating panel P13 ④ Rear panel P15 ⑤ Side panel P18 ⑥ Bottom panel P19 ⑦ Lamp P25 ⑧ Microphone 12
Operating panel ① ⑫ ② Mark ⑭ ⑬ ③ ④ ⑧ ⑥ ⑮ ⑤ ⑦ ⑨ ⑩ Name ⑪ Function To turn the power ON/OFF. ① Power Power ON ： Blue light Power OFF (standby status) ： Red light To turn the lamp ON/OFF ② Lamp Note The lamp is always OFF when power is turned on. turned on.
Mark Name Function To zoom in an object. ⑧ Zoom In Note The lamp is always OFF when power is turned on. 。 ⑨ Zoom Out To zoom out an object. ⑩ Bright To brighten the camera image. ⑪ Dark To darken the camera image. ⑫ Video Output LED [HDMI] When this LED is lit in blue, digital video is output. Select the output mode with the Image Selection button. When this LED is lit in blue, analog RGB video is ⑬ Video Output output. LED [RGB] Select the output mode with the Image Selection button.
Rear panel and cable connections ① ② ③ ④ ⑤ ⑥ Mark ⑦ Function Name Security slot ① Plug-in for the AC adapter. ② Connect the supplied AC adapter. To connect the product to a PC. (USB cable is supplied with the product.) ③ Connect the Mini-B-Type connector to the product. ④ RGB OUT ⑤ RGB IN To output analog RGB video. (Analog RGB cable is not supplied with the product.) To output the video input to the [RGB-IN] terminal from the [RGB-OUT] terminal. To output digital video.
① To connect a security cable. An anti-theft security cable can be connected. An anti-theft security cable is not supplied with the product. ② To connect the AC adapter. Before inserting the AC adapter in an outlet, connect the DC plug of the supplied AC adapter to the [ ] terminal on the rear panel. ③ To connect the product to a PC with a USB cable. Install the control software “Image Mate” contained in the supplied CD-ROM onto your PC to connect the product to a PC.
⑦ To connect the product to a device with an HDMI output terminal. Connect a commercially available HDMI cable to the [HDMI IN] terminal on the rear panel. The product has a Standard HDMI (Type A) terminal. Press the Image Selection button to light up the Video Output LED [EXT]. Note • If the displayed image is off-center, adjustment of the horizontal and vertical position should be made from the connected device. • In some cases, vertical stripes may appear on the display device.
Side Panel ① Function ① To insert an SD card (commercially available). Push the card again to remove the SD card.
Bottom panel ① Output resolution from the RGB OUT terminal can be changed with the dip switch. Change Resolution Function Switch MENU XGA WXGA ① MENU XGA WXGA MENU XGA WXGA MENU Analog RGB output resolution can be changed from the OSD menu settings. XGA Analog RGB output resolution is fixed to XGA. WXGA Analog RGB output resolution is fixed to WXGA. Note ・ When the dip switch is set to XGA or WXGA, the resolution setting of the OSD menu is disabled.
３ PREPARATION AND CONNECTION Setting Up Note ・Carry the product by holding the lower part of the body in both hands. Never hold the product by the arm or the camera head. ・Pay attention to prevent the camera head from knocking against a desk or the like. ・Move the arm while supporting the body with your hand. ② Lift up the other side of the arm. ① Hooking your finger to the position indicated by an arrow in the drawing, slightly lift up the arm.
Moving Parts of the Mobile Document Camera This unit can be moved as shown below.
Connecting to a projector or a monitor Set up the product as shown in the above drawing and turn on the power after connecting a projector or a monitor. Note • Either an HDMI signal or an analog RGB signal can be output to a projector or a monitor. Output signal can be selected with the Image Selection button.
Connecting to a PC Set up the product as shown in the above drawing and turn on the power after connecting a PC.
Turning on the power Power supply from the AC adapter 1. Connect the AC cord and the AC adapter. Then connect the AC adapter to the [ ] terminal at the rear panel of the product, and insert the AC cord into an outlet. 2. Turn the power on by pressing the power button on the operating panel. Power supply from the USB Note To operate the product with the power from the USB, a USB port that can output more than 3.4W is needed. When supplying the power from the USB, connect to the USB3.
4 SHOOTING IMAGES Adjusting the size The display range of the document can be adjusted by pressing the [ / ] buttons on the operating panel. [ ]：ZOOM-IN・・・・・・The object can be shown in large size. [ ]：ZOOM-OUT・・・・The object can be shown in small size. Note Zoom ratio: Digital Max 8x. Image quality will be degraded when ZOOM-IN. Still images and the images saved in an SD card cannot be zoomed in or out.
Saving a still image Press the [ card. ] button for long (more than 1 second) to save a still image to the SD Rotating the image ・Live image (Camera image): 【Upside▲】 mark in the camera head indicates the direction of the sensor. The image appears upside-down when the camera head is set as shown in the below drawing. The image rotates by 180°by pressing the [ ] button. ・Still image (Camera image): The image rotates counterclockwise by 90°by pressing the [ ] button.
Switching the output video The Video Output LED of the output terminal used is lit. The output video can be selected by pressing the Image Selection button. Video Output Function LED ① HDMI A video signal is output from the HDMI OUT terminal. ② RGB A video signal is output from the RGB OUT terminal. ③ USB The product can be connected to a PC via a USB cable.
In the order that the output video changes (in the order that the LED lights up) Connected Item ① Image Selection Button ② Image Selection Button ③ Image Selection Button → EXT → To ① → USB EXT → To ① AC Adaptor Power ON HDMI → RGB USB Cable Power ON USB → No Change Power ON HDMI → RGB AC Adaptor USB Cable Note ・ When the USB power supply is enabled (when the AC adapter is not used) and when the power is OFF (standby status), a video signal input to the [RGB IN] terminal is ou
5 CHANGING THE SETTINGS Various settings for the product are changed through the menu (characters and icons) displayed on the screen. Changing the settings ① Press the [ ] button on the operating panel to display the menu on the screen, and then use the[ ② Press the [ ] button to move the cursor to the icon you want to operate or set. ] button to select the setting values.
Descriptions of each menu Camera output display mode menu Icon Name Selection Item Factory Function Setting To display the setting menu Preferences for the camera image. To display thumbnails of Thumbnails images saved in the SD card. Exit To hide the menu. Setting menu (Second layer) Icon Name Selection Item Factory Function Setting To set the HDMI output 1080i resolution. The resolution that the Resolution connected display device 720p 60fps does not support cannot be *1 set.
Icon Name Selection Item Off Flickerless Factory Japan/ 60Hz U.S. 50Hz Function Setting Others To lower the fluorescent light flickering due to power frequency. Select the same value as used for the power supply frequency. The white balance is adjusted automatically to Auto ensure a more natural color according to the shooting scene. Suitable for the scene White Balance Natural where there is outside light. Suitable for the scene Fluorescent under a fluorescent light.
Icon Name Selection Item Factory Function Setting To format the SD card. Yes (No operation is allowed Format during the formatting No process.) Clock Set To set the time. To return to the camera Exit output display mode menu. Note When the output resolution is HDMI, actual output resolution might be different from the resolution set by the Setting menu depending on the connected monitor.
6 USING A USB Installing the software Install the control software “Image Mate” contained in the supplied CD-ROM onto your PC to connect the product to a PC. For details about the operating environment and the OS of the connected computer or the operation of the software, refer to the installation manual of Image Mate. Connecting to a PC Set up the product as shown in the above drawing and turn on the power after connecting a PC.
Controlling the product from a USB-connected PC By using the “Image Mate”, you can perform the following tasks: ・To transfer the camera image to a PC ・To operate the product from a PC CAUTION ・Do not connect/disconnect the USB cable while operating the operating panel. ・We recommend using a USB 2.0-compliant USB cable. ・ Use a high specification PC (Core2Duo or higher) or down-convert the resolution to 640x480.
7 USING AN SD CARD With this product, you can save the camera image as a picture on an SD card. You can also display the data stored in the SD card on the screen. Before you begin, insert a commercially available SD card into the SD card slot of the side panel. Note ・ SD card ・The SDXC card cannot be used. ・Formatting the SD card with the product before you use is recommended. ・Using the SD card class 6 or higher is recommended.
Saving images ① Press the [ ] button on the operating panel for 1 second or more while the menu is not displayed on the screen. ② Saving begins when [ ] appears on the screen. Displaying the saved data ① Press the [ ] button on the operating panel to display the menu. ② Select [ ] and press the [ thumbnails (list of pictures). ] button on the operating panel to display ③ Move the cursor using the [ panel.
Thumbnail display mode Thumbnail display mode menu Icon Name Selection Item Factory Function Setting To display the camera Camera image. Still image display mode menu Icon Name Selection Item Factory Function Setting To display the camera Camera image. Yes To delete the displayed still Delete image. Next image is displayed after the deletion. No Exit To hide the menu.
8 TROUBLE SHOOTING If you have a problem or questions about this product, please read this troubleshooting guide first. If the problem still exists, consult the dealer from whom you purchased this product. Symptom No image is displayed. Possible cause/ remedy • The cable is not properly connected. • The AC adapter is disconnected from the wall outlet. • The AC adapter is disconnected from the power supply socket of the unit. • The power is not ON.
Symptom The image is striped. Possible cause/ remedy • This may be interference fringes between dots of the printed material and TV scanning lines or CMOS pixels. Changing the shooting range may help the problem. • Vertical stripes may appear on an LCD projector image. Manually adjusting the dot clock at the projector side may help the problem. There is a flickering of the • Set the value of the flicker correction in the menu same as fluorescent light. the power frequency of your area.
9 SPECIFICATIONS General Item Specifications DC5V（AC adapter AC100～240V） PC requirements for the power supply from a USB: - A PC with the USB3.0 port Power source - A PC with 2 USB ports Refer to P22 for details about the connection procedure. Power consumption Outside dimensions 4.2W(DC5.0V) (USB Power Supply：3.3W) W101×D416×H338［mm］（When setup） W101×D 行 226×H28［mm］（When folded） Weight Approx.
Item Limit of focus Specifications From lens surface 70mm～∞ adjustment Focus Auto/ Manual Image pick-up element 1/3.2” 5M pixel CMOS Sensor Effective pixels Horizontal 2048, Vertical 1536 Sync. system Internal HDMI output Image output 1080i, 720p(max Shooting area: 342mmx192mm) 720p (max Shooting area: 214mmx120mm) Analog RGB output Analog RGB output 0.7V(p-p) WXGA：1280x800 @60Hz 75Ωunbalanced Horizontal frequency Sync. signal :49.702kHz WXGA ：Horizontal negative Vertical frequency:59.
Trademarks and License and Image Mate are registered trademarks of ELMO Co., Ltd. SD、SDHC、 (SD logo) and (SDHC logo) are trademarks of SD-3C, LLC. HDMI, logo and High-Definition Multimedia interface are trademarks or registered trademarks of HDMI Licensing LLC. All other company/ product names described in this manual are trademarks or registered trademarks of their respective companies. WARNING • Unauthorized recording of copyrighted slide films, materials, photographs, etc.
6-14, Meizen-cho, Mizuho-ku, Nagoya, 467-8567, Japan OVERSEAS SUBSIDIARY COMPANIES ELMO USA CORP. Headquarters 1478 Old Country Road Plainview, NY 11803-5034, U.S.A Tel:(516) 501-1400 Fax:(516) 501-0429 E-mail: elmo@elmousa.com Web: http://www.elmousa.com West Coast Branch Cypress Pointe Business Park 5676 Corporate Avenue Cypress, CA 90630, U.S.
