Edition: 12.2009 · 610.44440.40.200 Original operating instructions · English Supplementary instructions L-BV2, L-BV5 Supplement to instruction manual 610.44440.40.
Concerning 1 Safety Content Concerning 1 Safety Concerning 1 Safety.........................................2 Concerning 1.2 General safety instructions.2 Concerning 1.2 Concerning 2 Correct use of the equipment ....3 Concerning 3 Technical Data ...........................5 Concerning 3.3 Operating conditions, normal operation............... .............................5 Concerning 5 Installation..................................5 Concerning 5.1 Installing the unit ................5 Concerning 5.
Concerning 2 G-BH1 units Concerning 2 Correct use of the equipment Point 2 “Intended Use” from 610.44440.40.
Concerning 2 Correct use of the equipment If the specified maximum temperatures are complied with, the units are suitable for temperature class T3. Foreseeable misuse The following are forbidden: Use of the unit2BV2 060 2BV2 061 2BV2 070 2BV2 071 2BV5 110 2BV5 111 2BV5 121 2BV5 131 2BV5 161 in nonindustrial plants, unless the necessary precautions and protective measures have been taken at the plant, e.g. protection against contact by children's' fingers.
Concerning 3 Technical Data Concerning 3 Technical Data Concerning 5.2 Concerning 3.3 Concerning 5.2.1 Connecting the suction and discharge branches Operating conditions, normal operation............... In order to prevent overloading from throttle on the discharge side, pressure monitoring (G2, Fig. 1, page 6) must be installed on the other side of the unit’s gas output flange. If the maximum outlet pressure p2 max specified in the 610.44440.40.000 operating manual section 3.
Concerning 5 Installation b) Operating fluid temperature measurement in the drain tapping (F2, Fig. 1, page 6), or on the unit housing (F5, Fig. 1, page 6) with suitable temperature sensor. Disconnection condition: Temperature ≥ 60 °C (140 °F) The measurement and control device must be suitable or certified to take reliable measurements for disconnection conditions and shut down the equipment if necessary.
Concerning 5 Installation NOTE The liquid level monitoring device (Fig. 1, page 6) is equipped with a shut-off valve which opens after the unit is switched off and closes again before starting up after the filling level has been regulated. If a connection between the device and the ambient atmosphere is not possible, or undesirable, due to the type of media used, the line should be routed back into the equipment behind the shut-off valve on the suction side in a suitable way (Fig. 1. page 6). 2BV2 0..
Concerning 7 Operation Concerning 5.2.4 Ancillaries Concerning 5.3 Connecting the motor electrically............... Operating fluid separator The accompanying drive motor operating manual must be strictly adhered to: The 2BX1 102, 2BX2 103 und 2BX1 107 stainless steel separators do not come under guideline 94/9/EG as they don’t have their own ignition sources. The propellant gas and the operating fluid must not react chemically to the separator.
EU Declaration of conformity EU Declaration of conformity EU declaration of conformity Manufacturer: Gardner Denver Deutschland GmbH P.O. Box 1510 D-97605 Bad Neustadt / Saale Responsible for documentation: Holger Krause P.O. Box 1510 D-97605 Bad Neustadt / Saale Designation: L Series Liquid ring vacuum pump/ compressor L-BV2, L-BV5 Types 2BV2 060-..D..-Z 2BV2 061-..D..-Z 2BV2 070-..D..-Z 2BV2 071-..D..-Z 2BV5 110-..D..-Z 2BV5 111-..D..-Z 2BV5 121-..D..-Z 2BV5 131-..D..-Z 2BV5 161-..D..-Z 2BV2 060-.
Form for statement on safety Form for statement on safety Statement on health safety and on the protection of the environment For the safety of our employees and to comply with statutory requirements on handling substances harmful to the health and the environment, this statement must be enclosed, fully completed, with each unit/system sent.
© Gardner Denver Deutschland GmbH 11 / 12 610.44440.40.
www.gd-elmorietschle.de er.de@gardnerdenver.com Gardner Denver Schopfheim GmbH Roggenbachstraße 58 79650 Schopfheim · Deutschland Tel. +49 7622 392-0 Fax +49 7622 392-300 Elmo Rietschle is a brand of Gardner Denver‘s Industrial Products Group and part of Blower Operations. Gardner Denver Deutschland GmbH Industriestraße 26 97616 Bad Neustadt · Deutschland Tel.
