Sliding Shower Door /8mm Installation Instructions Size:48"x78" 60"x78"
●Please read these instructions in full before installing IMPORTANT ● If this product is installed on top of shower tray, order to achieve a better water proof function, it is strongly suggested that the tray’s threshold width is not less than 60mm. ●Check that the tray has been installed to the manufacturer’s instructions. Please note - All product is supplied without a tray. ●Opening wall adjustments 48"Slider-adjustment=(46.81"-48")x78" 60"Slider-adjustment=(58.
IDENTIFICATION OF PARTS 2ES22 2ES21 2ES23 2ES20 2ES04 2ES01 2ES02 2ES19 2ES03 2ES05 2ES06 2ES07 2ES24 2ES08 2ES18 2ES09 2ES17 2ES10 2ES16 2ES15 2ES11 2ES12 2 2ES14 2ES13
Fixings & fittings supplied Item No.: Part Quantity Item No.: Part Quantity 2ES01 X1 2ES15 X1 2ES02 X 10 2ES16 X1 2ES03 X1 2ES17 X1 X2 2ES18 X1 2ES05 X4 2ES19 X1 2ES06 X1 2ES20 X1 2ES07 X1 2ES21 X1 X8 2ES22 X2 2ES09 X1 2ES23 X2 2ES10 X1 2ES24 X1 2ES11 X1 2ES25 X1 2ES12 X1 2ES26 X1 2ES13 X1 2ES27 2 .
Product Direction RH LH The slider is ok to be installed in left hand and right hand. The following step is based on right hand. For left hand, please follow the step in mirror direction.
1 ASSEMBLY INSTRUCTIONS 2ES03 2ES02 X1 X4 2ES05 2ES08 ST4X40 X4 X4 - Put the wall profile 2ES03(X1)against the wall and ensure it is vertical by spirit l.evel - Mark the holes on the wall. -Drill the holes accordingly. -Insert wall plugs 2ES02(X4) into the holes. -Fasten the wall profile on the wall with screws 2ES08(X4) and 2ES05(X4). 2ES03 1X φ6mm 4X m) m (10 39" 0.
2 ASSEMBLY INSTRUCTIONS - Insert fix panel 2ES07 in to the channel of wall profile.
3 ASSEMBLY INSTRUCTIONS 2ES27 2 .5mm X1 2ES28 2ES20 2ES23 2ES19 4mm X2 X1 X1 X1 - Mount wall bracket 2ES19 on the end of rail profile 2ES20. Fasten the screw by hex key 2ES27. -Mount rail profile 2ES20 on fix panel 2ES07 by fixing parts 2ES23(X2) and 4mm hex key 2ES28. Cover the screws on the back. -Mark the position of wall bracket on the wall. 2ES27 2ES20 2.
4 ASSEMBLY INSTRUCTIONS 2ES27 2ES28 2 .5mm X1 2ES20 2ES23 2ES19 X1 X2 X1 4mm X1 -Disassemble the rail profile 2ES20 from fix panel 2ES07 by loose fixing pars 2ES23(X2) with hex key 2ES28. -Disassemble the wall bracket 2ES19 from rail profile 2ES20 by loose screw with hex key 2ES27. 2ES27 2.
5 ASSEMBLY INSTRUCTIONS 2ES04 2ES02 2ES19 ST4X30 X2 X2 X1 - Take the wall seat from the wall bracket. -Drill the holes accordingly. -Insert wall plugs 2ES02(X2) into the holes. -Fix the wall seat on the wall with screw 2ES04.
6 ASSEMBLY INSTRUCTIONS 2ES27 2ES28 2 .5mm 2ES20 2ES19 2ES23 4mm X1 X1 X2 X1 X1 -Insert rail profile 2ES20 into the wall bracket 2ES19 and fasten them together with screw. -Assemble fixing parts 2ES23(X2) on the rail profile through fixing panel. 2ES20 2ES28 2ES27 2.
7 ASSEMBLY INSTRUCTIONS 2ES06 X1 2ES25 X1 - Adjust the position of fix panel to meet with opening requirement. Please make sure the same opening both on top and bottom. -Insert sealer 2ES06 between glass panel and wall profile from outside of cabin. 4 8 " = 2 4 .6 6 0 " = 3 0 .7 9 " (6 2 7 m m ) 8 " (7 8 2 m m) 2ES06 2ES07 4 8 " = 2 4 .6 6 0 " = 3 0 .
8 ASSEMBLY INSTRUCTIONS 2ES12 2ES11 2ES14 X1 X1 X1 -Apply silicone glue on the back of the bottom anti-water profile 2ES12 and sliding guide 2ES11 and end cover 2ES14. -Put sliding guide 2ES11 next to the fix panel. Insert bottom profile 2ES12 into the guide. Put cover 2ES14 on the other end of 2ES12. 2ES12 2ES14 2ES11 2ES07 ! 47 Please note that the width of the sliding guide which stands on the tray threshold should be no less than 47mm.
9 ASSEMBLY INSTRUCTIONS 2ES13 2ES18 X1 2ES21 X1 X1 2ES22 2ES24 X2 X1 - Mount rollers 2ES22(X2) on sliding panel 2ES18. - Mount anti-jump part 2ES21 on the sliding panel 2ES18. - Mount handle 2ES24 on the sliding panel. - Apply bottom sealer 2ES13 on the bottom of sliding panel..
10 ASSEMBLY INSTRUCTIONS 2ES10 2ES17 X1 X1 - Apply magnetic strip 2ES17 on the sliding panel edge next to the handle. -Apply vertical sealer 2ES10 on the other edge of sliding panel for left hand installation. For right hand installation, apply vertical sealer 2ES09 on the edge of sliding panel.
11 ASSEMBLY INSTRUCTIONS 2ES09 2ES10 X1 X1 - Apply vertical sealer 2ES09 on the edge of fix panel for left hand installation. -Cut the extra part on top according to below. -For right hand installation, please apply vertical sealer 2ES10 on the fixing panel edge and cut the extra part accordingly.
12 ASSEMBLY INSTRUCTIONS - Mount sliding panel on the rail profile. Put the top roller on the top of rail profile and put anti-jump part into the channel of rail profile. Make sure the bottom sealer of sliding panel into the channel of bottom sliding bracket.
13 ASSEMBLY INSTRUCTIONS 2ES15 2ES16 X1 X1 2ES16 - Insert magnetic stip 2ES16 into the small wall jamb 2ES15. -Put 2 magnetic strip closed on the sliding panel. -Close the door to mark the position of small wall jamb .
14 ASSEMBLY INSTRUCTIONS 2ES02 2ES08 ST4X40 X4 2ES15 X4 - Take off the magnetic strip out off small wall jamb. - Put the small wall jamb on the wall according to the mark. - Mark the holes position. - Drill the holes accordingly. - Insert wall plugs 2ES02(X4) into the holes. - Fix small wall profile on the wall with screw 2ES08(X4).
15 ASSEMBLY INSTRUCTIONS 2ES15 X1 2ES01 - Insert magnetic strip 2ES15 into the channel of small wall jamb. - Put top cover 2ES01 on the big wall profile.
16 ASSEMBLY INSTRUCTIONS 2ES26 X1 -The top roller is adjustable to make door vertical. -Take off the back cover off. Turn the nut on the back with tool 2ES26. - Turn the nut until the door is vertical with magnetic strip closing well. -Put the back cover on the roller.
17 ASSEMBLY INSTRUCTIONS - Apply silicone sealant to the outside of the enclosure. Please note: Do not apply silicone sealant to the inside of the enclosure. Cleaning and Maintenance: Please do not use abrasive or strong cleaning solutions on the shower enclosure, such as alcohol, petroleum liquids or any other chemical cleaner. Should there be any dirty stains on the shower enclosure, please clean it with a soft lint free cloth and warm soapy water. Please rinse it with clean water afterwards.
