ENLZSTL8WS_1G Enhanced INSTALLATION & USE MANUAL LZ ™ Series Bottle Filling Stations & Coolers * Versatile cooler design allows units to be installed either left-hand high and right-hand low or left-low and right high. Basin change may be required. See desired rough-in to help determine if the basin change is necessary. Important: The refrigerated coolers must be hung on the right side. Page 1 1000004543 (Rev.
1000004543 (Rev.
ALTERNATE ROUGH-IN FOR RIGHT-HAND HIGH, BOTTLE FILLER LOW MODELS – REQUIRES BASIN ASSY CHANGE Page 3 FILTER 13 15/16" 354mm 17 7/16" 443mm F B E 2 7/8" 73mm 15" 381mm A ALTERNATE LOCATION 3 7/8" 98mm 6 3/8" 162mm 7" 178mm D ALTERNATE LOCATION 7/8" 22mm 2" 51mm 6 3/8" 162mm C L 2" 51mm 5 3/4" 146mm 7" 178mm 6 3/8" 162mm FINISHED FLOOR 7" 178mm 6 3/8" 162mm ACTIVATION SENSOR 18 3/8" 467mm 24 1/2" 622mm 22 15/16" 583mm 19 7/16" 494mm F 34 5/16" 871mm 2" 51mm A PREFERRED LOCATION
1000004543 (Rev.
ALTERNATE ROUGH-IN FOR RIGHT-HAND LOW, BOTTLE FILLER HIGH MODELS – REQUIRES BASIN ASSY CHANGE Page 5 E 19 7/16" 494mm 22 15/16" 583mm F A ALTERNATE LOCATION D PREFERRED LOCATION 6 3/8" 162mm C L B C L 7" 178mm 3 7/8" 98mm 2" 51mm 6 3/8" 162mm 44 1/16" 1119mm 28 13/16" 731mm 2" 51mm 21 7/8" 556mm 19" 483mm 17 7/16" 443mm 13 15/16" 354mm F A PREFERRED LOCATION E O 9/32" (7mm) HOLES (12) 7/16" X 3/4" (11mm X 19mm) OBROUND HOLES (6) FINISHED FLOOR 7" 178mm 5 3/4" 146mm 6 3/8" 162m
ENLZSTL8WS_1G HANGER BRACKETS INSTALLATION 1) Remove hanger bracket fastened to back of coolers by removing one (1) screw. 2) Determine your mounting configuration from the figures shown on pages 2 - 5. Refrigeration unit must be on right hand side. IMPORTANT NOTE: If the Bottle Filler is to be mounted on the left hand cooler, a basin assembly change will be needed. Determine your configuration by referring to the Configuration Instructions on page 9 prior to continuing.
ENLZSTL8WS_1G BOTTLE FILLER INSTALLATION 14) Remove two (2) mounting screws with 5/32” Allen wrench holding Bottle Filler to wall mounting plate (See Fig. 8). Note do not discard mounting screws, they will be needed to secure Bottle Filler to wall mounting plate. 15) Remove wall mounting plate from Bottle Filler (see Fig. 8 ). Place wall mounting plate against wall on top of basin. Center the wall mounting plate side to side with the basin. Mark the six (6) mounting holes with a pencil (See Fig. 1, Pg.
ENLZSTL8WS_1G FINAL INSTALLATION (FILTER) 21) Remove filter from carton, remove protective cap, attach filter to filter head by firmly inserting into head and rotating filter clockwise. Ensure that filter label can be read when filter is installed. (See Fig. 12) 22) Turn water supply on and inspect for leaks. In both cooler and Bottle Filler. Fix all leaks before continuing. 23) Once cooler and bottle filter have been inspected for leaks and any leaks corrected, plug cooler into wall.
ENLZSTL8WS_1G CONFIGURATION INSTRUCTIONS INSTRUCTIONS TO MOVE THE BOTTLE FILLER & BASIN TO THE LEFT SIDE (NON-REFRIGERATED) FOR ALTERNATE MOUNTING VERSATILE BI-LEVEL Fig. A Fig. B Fig. C 1. Using a 5/16” socket, remove the (4) screws from the bottom of each cooler to remove the wrappers. 2. Remove filler panel from cooler using a 5/16” socket. 3. Using a T20 (6-point star) bit, loosen the shroud screws on both sides of both coolers. 4. Lift the basin/shroud assembly from each cooler.
ENLZSTL8WS_1G Refrigerated Cooler side: Carefully lift and tip the shroud/basin assembly off the cooler frame. Only disconnect the (2) black wires coming from the shroud assembly that go to the solenoid valve and to the cold control. Disconnect the water line at the solenoid valve. Reference (Fig. 21, p.14) for the operation of the quick connect fittings. FIG.17 Non-Refrigerated Cooler side: Carefully tip the shroud/basin assembly toward the cooler frame.
ENLZSTL8WS_1G PLUMBING DIAGRAMS VERSATILE BI-LEVEL Bottle Filler Drain Bottle Filler Drain Bottle Filler Drain Bottle Filler Drain Page 11 1000004543 (Rev.
ENLZSTL8WS_1G Versatile Wrapper and Trim Kit Installation Instructions Left Hand Wrapper (High Side) 1) Remove existing wrapper by removing the (4) screws from bottom. 2) Screw trim piece to wrapper with (2) screws (provided) 3) Re-install wrapper with (4) screws. 4) Dispose of unused cover plate. Revestimiento del lado izquierdo (Lado alto) 1) Retire los (4) tornillos de la parte inferior para retirar el revestimiento existente.
ENLZSTL8WS_1G Versatile Wrapper and Trim Kit Installation Instructions continued. . . Instrucciones de instalación versátiles de la envoltura y del juego de molduras continuadas. . . Instructions d’installation du kit d’emballage et de garniture polyvalentes (suite). . . Left Hand Wrapper (Low Side) 1) Remove existing wrapper by removing the (4) screws from bottom. 2) Clip cover plate, sliding until plate sits flush with the wall. 3) Re-install wrapper with (4) screws. 4) Dispose of unused trim piece.
ENLZSTL8WS_1G 115V Refrigerated Wiring Diagram with Alpha/Numeric Display 35 32 34 36 37 24 25 26 Fig. 19 SUPERSEAL FITTING ASSEMBLY OPERATION OF FITTINGS OPERATION OFQUICK QUICKCONNECT CONNECT FITTINGS SIMPLY PUSHIN IN SIMPLY PUSH TUBE TO TUBE TOATTACH ATTACH TUBE TUBEIS IS SECURED SECURED INPOSITION POSITION IN PUSH PUSHIN IN COLLET COLLET TORELEASE RELEASE TUBE TUBE TO A Note: Screw the locknut hand tight to seal2 A C Fig. 21 Fig. 20 1000004543 (Rev.
ENLZSTL8WS_1G 11 Basin Locknut BUBBLER DETAIL Fig. 22 NOTE: When installing replacement bubbler and pedestal, tighten nut only to hold parts snug in position. Do Not Overtighten. 3 2 1 Fig. 23 WATERSENTRY® Filter Detail WATERSENTRY® FILTER PARTS LIST ITEM NO. PART NO. 1 2 51300C 1000005214 3 1000004409 DESCRIPTION Filter Assy - 3000 Gal. Kit - Filter Head Fittings includes John Guest Fittings & 3/8" Elbow Filter Bracket/Screws Kit - NFC Board/Cover Page 15 1000004543 (Rev.
ENLZSTL8WS_1G Service Instructions Refrigerated Unit Lower and Upper Shroud 11 To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
Action Momentary Momentary Momentary Momentary Momentary Momentary Momentary Momentary Top level Info Info Set time Filter Refrig Range Page 17 B-Light EnerSave Momentary Momentary 100% Momentary Momentary 75% On Momentary 50% Off Momentary 25% Momentary Momentary Yes 1-10 Momentary No Momentary Momentary Min 0-69 in 5 minute increments Yes Momentary Hour (12 hour) Momentary Momentary AM/PM No Momentary Action Day (Sunday-Saturday Flashes error code Scrolls
ENLZSTL8WS_1G Pictured is unit only without bottle filler. Note: Danger! Electrical shock hazard. Disconnect power before servicing unit. Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A 14 1 28A 27 15 1 22 16 28B 10 8 6 5 10 3 12, 13 5 8 See Fig. 25 6 3 2A 12, 13 12 See Fig. 24 2B 20 12 17 20 9 23 27 7 20 20 30 31 20 Fig. 26 1000004543 (Rev.
ENLZSTL8WS_1G ATTENTION: If the product serial number is before 190424189, please refer to archived documents section of Elkay.com for the most accurate parts list. (www.elkay.com/archived-documents) 115V PARTS LIST / LISTA DE PIEZAS DE 115 V / LISTE DES PIÈCES 115 V ITEM NO. PART NO.
ENLZSTL8WS_1G FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment This device complies with Part 15 of the FCC Rules. Operation to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation INDUSTRY CANADA STATEMENT This device complies with Industry Canada license-exempt RSS standard(s).
