Installation Sheet

0000001029 (Rev.C - 11/14)
EZWS-EDFPBM117K LZWS-EDFPBM117K
Page 9
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
Note: Screw the locknut hand tight to seal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
56073C
55001132
55000944
45767C
28343C
45781C
98871C
98530C
56163C
45769C
45768C
56092C
70682C
55996C
36301C
111008343890
70432C
38417001
75560C
75632C
70817C
111577343890
28395C
0000001144
62223C
70852C
Kit - Bubbler Assy
Basin - Swirlow
Lower Shell
Fountain Body
Cover Plate
Sleeve
Kit - Swirlo Pushbutton/Spring
Kit - Regulator/Spring/Nut
Gasket - Drain
Assy - Drain/Tailpipe
Drain - Plug 1-1/2”
Poly Tubing (Cut To Length)
Tee - 1/4
Strainer
Reset Switch
Screw - #10-24 x .62 HHSM
Screw - #8-32 x .38 THSM
Screw - #8-18 x .37 HHSM
Screw - 5/16-18 x 1.00 HHMS
Setscrew - #10-32 x .38
Fitting - Elbow 1/4 x 1/4
Nut - Hex 5/16-18
Bracket - Support
Tee - 1/4 x 1/4 x 3/8
Copper Tube - 3/8”Cut to Length
Tee - 3/8”
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
Figure 11 – Water Supply Connections
PARTS LIST
ITEM NO.
PART NO.
DESCRIPTION
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
1/4” O.D. TUBE
WATER INLET
TO COOLER
3/8” O.D. UNPLATED COP-
PER TUBE CONNECT
COLD WATER SUPPLY
DESCRIPTION
98543C
98544C
98545C
98546C
98549C
Kit - Electrical Package
Kit - EE Sensor
Kit - Solenoid Valve Replacement
Kit - Aerator Replacement
Kit - Hardware & Waterway Parts
BOTTLE FILLER REPLACEMENT
PART KITS
ITEM NO. PART NO.
28
29
30
31
32
Installation Package
The components for installation are packed in
two separate boxes, regardless of the type of unit
being installed. The boxes contain the following:
Box No. 1: Wall Frame(s)
Box No. 2: Fountain(s), Arm(s) and Panels
Additional materials, as noted in the Parts List,
are also shipped in these boxes.
TROUBLESHOOTING & MAINTENANCE
Orice Assembly: Mineral deposits on orice can
cause water ow to spurt or not
regulate. Mineral deposits may
be removed from the orice by
poking with a small round le
not over 1/8” diameter, or using
a small diameter wire.
DO NOT le or cut orice
material
Stream Regulator: If orice is clean, regulate
ow as in Step 14 of the installation instructions. If
replacement is necessary, see parts list for correct
regulator part number.
Figure 13 – Quick Connect Fittings
Actuation of Quick Connect Water Fittings: Cooler
is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the tting,
relieve water pressure, push in on the gray collar while
pulling on the tubing. (See Figure 13) To insert tubing,
push tube straight into tting until it reaches a positive
stop (approximately 3/4”).
Figure 12