Installation Sheet

ManualsBrandsElkay ManualsCoolersWall Mounted Versatile Cooler Bi-Level Hands-Free Non-Filtered Refrigerated in Stainless Steel Color

Page 1

EZOTL8*1H

1000002687 (Rev. B - 01/19)

Versatile Cooler Model EZOTL8

conguration as shipped

Versatile Cooler Model EZOTL8

alternate installation

Manual de instalación y uso

Manuel d’installation et utilisation

INSTALLATION AND USE MANUAL

EZOTL

™

Série versatile refroidisseurs d’eau à deux niveaux

EZOTL

™

Serie versátil bi-nivel enfriadores de agua

EZOTL

™

Series Versatile Bi-Level Water Coolers

Summary of content (9 pages)

PAGE 1
EZOTL8*1H INSTALLATION AND USE MANUAL Manual de instalación y uso Manuel d’installation et utilisation EZOTL™ Series Versatile Bi-Level Water Coolers EZOTL™ Serie versátil bi-nivel enfriadores de agua EZOTL™ Série versatile refroidisseurs d’eau à deux niveaux Versatile Cooler Model EZOTL8 configuration as shipped Versatile Cooler Model EZOTL8 alternate installation Page 1 1000002687 (Rev.
PAGE 2
EZOTL8*1H Note: Danger! Electrical shock hazard. Disconnect power before servicing unit. Nota: peligro! Peligro de descarga eléctrica. Desconecte antes de reparar la unidad Remarque : Danger ! Risque de choc électrique. Débrancher avant de réparer l’appareil.
PAGE 3
FIG.
PAGE 4
1000002687 (Rev. B - 01/19) E Page 4 7" 178mm 7/8" 22mm 2" 51mm B ‰ 2" 51mm F D ALT.
PAGE 5
EZOTL8*1H Versatile Wrapper and Trim Kit Installation Instructions Left Hand Wrapper (High Side) 1) Remove existing wrapper by removing the (4) screws from bottom. 2) Screw trim piece to wrapper with (2) screws (provided) 3) Re-install wrapper with (4) screws. 4) Dispose of unused Right Hand Wrapper (Low Side) 1) Remove existing wrapper by removing the (4) screws from bottom. 2) Clip cover plate, sliding until plate sits flush with the wall. 3) Re-install wrapper with (4) screws.
PAGE 6
EZOTL8*1H HANGER BRACKETS INSTALLATION 1) Remove hanger brackets fastened to back of cooler by removing one (1) screw. 2) Mount the hanger brackets as shown in Figures 2 or 3. NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support. Anchor hanger securely to wall using all six (6) 1/4 in. dia. mounting holes. INSTALLATION OF COOLER 3) Hang the cooler on the hanger bracket.
PAGE 7
EZOTL8*1H Service Instructions Lower and Upper Shroud To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
PAGE 8
EZOTL8*1H SENSOR RANGE ADJUSTMENT: The electronic sensor used in this cooler is factory pre-set for a “visual” range of 36 inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment procedure below: - Using a small tip screwdriver, locate range adjustment screw through the small hole between the sensor lenses (See Page 2.) Turn this screw clockwise to increase range and counterclockwise to decrease range (See Fig. 4).
PAGE 9
EZOTL8*1H 115V PARTS LIST/ 115V LISTA DE PIEZAS/ 115V LISTE DES PIÈCES ITEM NO. PART NO. DESCRIPTION 1 2 3 4 *5 6 7 8 9 16 17 18 19 20 21 22 98724C 30873C 55001109 28401C 36322C 36028C 98734C 0000000238 36285C 31376C 1000001602 1000004447 56073C 56092C 56213C 56228C 56229C 66703C 1000001994 97969C 55996C 1000004572 98773C 98775C 23 24 98776C 98777C 25 26 27 28 29 NS 98778C 98896C 98898C 1000004984 1000004564 28024C 28025C 1000000888 1000000944 1000000758 1000000759 Kit - Evaporator Assy.