Installation Sheet

ManualsBrandsElkay ManualsKitchen AccessoriesElkay WaterSentry VII Filter Kit for Elkay Coolers and Fountains

Page 1 97747C (Rev. N - 06/19)

WaterSentry

Water Cooler.

7. Turn on water supply and hold open the bubbler on

cooler until approximately 1 gallon of water is dis-

 pensed.Thisushingprocedurepurgesairandne 

 carbonparticlesfromthelter.When1gallonofwater

has been purged through the cooler, carefully inspect all

water connections for leaks.

LK1141A Bubbler with or without a chiller unit, under

sink application.

1. Open inlet water supply valve, open dispensing valve

or bubbler and allow approximately 1 gallon of water to

 bedispensed.Thisushingprocedurepurgesairand

 necarbonparticlesfromthelter.

2. Turn dispensing valve off and carefully inspect all water

connections for leaks.

3. Unit is now ready for operation.

TheselterkitsaredesignedtobeusedwithavarietyofElkay

products including:

1. WaterCoolersandDrinkingFountains.(Note-ForBottleFiller

 modelsuse51300C.)

2. LK1141ABubblerwithorwithoutachillerunit.

3. Independentlyinanundersinkapplication.Forundersink

applications, it is recommended that water be dispensed

through a dedicated valve or faucet instead of the sink faucet

 duetothereducedowthroughthelter.

NOTICE: Do not use with water that is microbiologically

unsafe or of unknown quality without adequate

disinfection before or after the system.

General Installation Instructions

1. Theselterkitsmustbeinstalledincompliancewithall

state and local laws and regulations governing the

installation and use of this product. Maximum inlet water

temperature 100°F(38°C).

2. Mountlterheadinasuitablelocation,usingthelter

mounting bracket and screws supplied. Allow enough

 roomunderthelterheadforinstallationandremovalof

 ltercartridge(13"minimum).

3. Connectthecoldwatersupplytothelterthroughashut-off

 valveand3/8"O.D.tubing(suppliedbytheinstaller).For

ease of servicing, the shut-off valve should be located within

 easyreachofthelter.

 NOTE:Theinletandoutletttingsuppliedaspartofthe

 lterheadareJohnGuestSupersealttingsthataccept

 3/8"O.D.tubingonthelterinletand1/4"O.D.tubingon

the outlet. They may be used with copper, semirigid nylon

or polypropylene tubing, with a rated working pressure

equal or greater than encountered in application. Do not

use soft or braided tubing.

4. CAUTION: If supply pressure will ever exceed 100 psi,

install a pressure regulator to limit the inlet pressure to

 thelterto100psiorbelow.

DO NOT ATTACH HOT WATER LINE TO FILTER.

 Tomakeconnectionsonthelterhead,loosenlocknut.Push

 thetubeendpastbotho-ringstoapositivestopinthelter

 headrecess-approx.1",locknutmayhavetobebackedout

 alittlemore.Screwthelocknuthandtighttoseal(SeeFig.1).

 Endsoftubingmustbecutsquareandfreeofburrsandsharp

ends that could cut or nick the o-rings.

5. Connecttheoutletoftheltertotheinletoftheunion

 usingthe1/4"O.D.polytubingand1/4"unionsupplied.

6. Removelterfromcarton,removeprotectivecap,attachlter

 tolterheadbyrmlyinsertingintoheadandrotatinglter

clockwise.

FIG. 2

FIG. 1

See Note 4: Screw the locknut hand tight to seal

Filter Replacement*

1. Turn inlet water valve off.

2. Open bubbler to relieve pressure build-up in the system.

3.Removelterfromheadbyrotatingltercounterclockwise.

4.Removenewlterfromcarton,removeprotectivecap;

capmaybeplacedonoldltertoreducethechanceof

waterspillingfromlterhousing.

5.Attachltertolterheadbyrmlyinsertingintoheadand

rotatinglterclockwise.

FILTER KIT

EWF172 WaterSentry

VII Kit

(Lead, Chlorine, Taste & Odor and Particulate Class I Reduction)

FOR COMMERCIAL USE ONLY

IMPORTANT NOTE – To avoid danger of an electric shock hazard, disconnect

power to your unit before installing or replacing the lter.

TheWaterSentry

VII lteristestedandcertiedbyNSFInternationaltoNSF/ANSI42and53for

thereductionofChlorine,TasteandOdor,ParticulateClassI,andLead.

Summary of content (5 pages)

PAGE 1
FILTER KIT EWF172 WaterSentry® VII Kit (Lead, Chlorine, Taste & Odor and Particulate Class I Reduction) FOR COMMERCIAL USE ONLY IMPORTANT NOTE – To avoid danger of an electric shock hazard, disconnect power to your unit before installing or replacing the filter. ® The WaterSentry VII filter is tested and certified by NSF International to NSF/ANSI 42 and 53 for the reduction of Chlorine, Taste and Odor, Particulate Class I, and Lead.
PAGE 2
NOTE: The filter head contains an automatic shut-off valve that stops the flow of water, if the filter is removed inadvertently without shutting off the incoming water. RATED OPERATING CONDITIONS Pressure (Max.) Pressure (Min.) Flow Rate Rated Capacity Temperature (Max.) Temperature (Min.) 105 PSI (7.4 Kg/cm2) 20 PSI (1.4 Kg/cm2) 1.5 GPM (5.7 LPM) 1,500 Gallons (5,679 L) 100° F (38° C) 40° F (5° C) NOTE: Performance will vary depending on local water conditions.
PAGE 3
Configuration Examples FILTER LOCATION FILTER LOCATION LMABFTL* LMABF* LVRC* FILTER LOCATION LVRCTL* Page 3 FILTER LOCATION 97747C (Rev.
PAGE 4
Configuration Examples LFAE* LFDE* LWAE* LWCE* FILTER LOCATION FILTER LOCATION LK1141A & REMOTE CHILLER WATER "IN" TO REMOTE CHILLER 1/4" (6mm) UNION (SUPPLIED) CHILLED WATER SUPPLY TO VALVE 1/4" (6mm) O.D. TUBING (SUPPLIED) COLD WATER SUPPLY TUBE 3/8" (10mm) INSTALLATION WHEN USED WITH WATER CHILLER PLUMB FILTER OUTLET DIRECTLY TO LK1141A OR OTHER CLASSROOM BUBBLER See page 5 for replacement information. 97747C (Rev.
PAGE 5
NOTICE To receive maximum benefit from your ELKAY® WaterSentry® filters, note the installation dates below and change according to the following guidelines. ELKAY Part No. 51299C WaterSentry® VII -- Lead Reduction Filter Change every 1,500 gallons, or once a year -- whichever occurs first. -- KEEP THIS SHEET IN A HANDY LOCATION -DATE INSTALLED MODEL (TYPE OF FILTER) SERVICE PERSON DATE INSTALLED MODEL (TYPE OF FILTER) SERVICE PERSON FOR REPLACEMENT FILTER, PLEASE CALL 1.800.834.