ENERGY SAVING Installation and Maintenance Manual DSWH160UVPC Table of Contents Declaration of Conformity Association Recommendations for Safeguarding the Environment Explanation of Warning/Safety Icons Introduction Components Guide Product Specifications 2 2 3 3 4 5 6 Before You Begin – Requirements for Installation Mounting Dimensions Operating Environment Water Electrical Tools You Will Need Unpacking the Kit What’s in the Kit Installing the Machine 7 7 8 8 8 9 9 10 11 Operating the Keypad Routine
DSWH160UVPC Installation and Maintenance Manual Declaration of Conformity D.M. 174 Materials compliant for contact with drinking water TA LY C NI 10 0 % M AD E T I F I C AT E ER I This unit is intended for the dispensing of drinking water, and so the materials that enter into direct contact with water meet the criteria for food-grade components pursuant to the current legislation.
ITPI rosso 032 c I TA LY C 10 IN T I F I C AT E ER 0 % M AD E D.M. 174 ITPI rosso 032 c Recommendations for Safeguarding the Environment Packaging materials The packaging materials are 100% recyclable. Please follow the local guidelines on waste disposal. For safety reasons keep the packaging material out of the reach and sight of children. Scrappage The DSWH160UVPC water cooler is made using recyclable material.
DSWH160UVPC Installation and Maintenance Manual Introduction The DSWH160UVPC cooler brings contemporary style and state-of-the-art technology to commercial water dispensers. DSWH160UVPC offer the highest level of quality and modern design.
Components Guide DSWH160UVPC Removable top cover Keypad Front door Drip tray Front Panel lock Water inlet CO2 inlet Power cord DSWH160UVPC Keypad Cold sparkling dispenser Cold still dispenser Hot dispensers ENERGY SAVING Energy Saving button ENERGY SAVING LED alarms Energy Saving No/low H20/CO2 pressure ENERGY SAVING 1000003740 (Rev.
DSWH160UVPC Installation and Maintenance Manual Product Specifications Specification 4 (15) 85 6 oz. cups/h Cold water temperature 42°F – 48°F (5.5°C – 8.8°C) Ice bank capacity gal (lt) 2 (7) Ice bank lb (kg) Cooling technology Condensation Adjustable cooling thermostat Refrigerant gas Pump Max hot water temperature Hot water tank capacity gal (lt) 6.6 (3.5) ICE BANK single stainless steel coil Ventilated Yes HFC R134a Professional booster pump 185°F (85°C) 0.
Before You Begin – Requirements for Installation Mounting Dimensions Over counter (includes 4" clearance on sides and back) DSWH160UVPC Depth 23.2” (589mm) Width 20.9” (531mm) Height 22.4” (569mm) Footprint: 12.9” wide x 19.2” deep 330mm x 489mm Under counter Depth 3.88" (99mm) Width 3.25" (83mm) Height 12.75" (324mm) Height 28" (711mm) Water filter Diameter 8" (203mm) CO2 cylinder (typical, 20 pound) 1000003740 (Rev.
DSWH160UVPC Installation and Maintenance Manual Operating Environment OO OO Install the machine in a clean, dry, well-ventilated room. It is designed to function correctly in environments with a temperature of 16°C to 32°C – Climatic Class N, (between 61°F and 90°F). Check that the water cooler is level, that it is on a surface that can support its weight and in an environment suitable for its size and use. OO Do not place the machine near a source of heat.
Tools You Will Need (2) 8" adjustable wrenches (1) 12" adjustable wrench (1) 12" pipe cutter (1) 10" adjustable pliers (1) universal screwdriver (1) wire cutting pliers Unpacking the Kit Remove the front panel (labeled FRONT) and cover of the wooden packing case. Remove the cardboard box and the internal protective packaging by sliding them up and over the top. Once you have unpacked the machine, check all components to ensure that they are not damaged.
DSWH160UVPC Installation and Maintenance Manual What’s in the Kit (1) 10' coil water 3/8” OD tubing (blue) Front panel keys (1) CO2 regulator PLUS (1) supply hose 1/2 ips x 3/8 tube x 12” long (2) 3/8" – quick connect connector (1) 3/8” x 3/8” 90° quick connect elbow (1) water pressure regulator (1) DSWH160UVPC water cooler (1) external water filter (1) 10' coil CO2 tubing (natural) 1/4” OD (1) 3/8” x 1/4” quick connect connector NOTICE: CO2 source is not included and must be supplied separately.
Installing the Machine CAUTION: Wear safety gloves when handling the machine. Metal edges are sharp, and touching them could result in minor or moderate injury. CAUTION: The unit weighs more than 100 lbs (45 kg) when the ice bank is filled. Lifting without proper support could result in minor or moderate injury. 1. Install external water filter and CO2 cylinder. 1. Use (2) Phillips head screws to mount bracket to under-counter wall or DSCABWH cabinet panel. 2.
DSWH160UVPC Installation and Maintenance Manual 2. Cut, size and connect water and CO2 piping to fit your installation. NOTICE: The water pressure entering the machine must be between 14.5 psi (0.10 MPa) minimum and 51 psi (0.35 MPa) maximum. If the inlet water pressure is higher than 51 psi, the water pressure regulator supplied must be used. NOTICE: An incoming flow rate of >1.0 gallon/minute is recommended for optimal quality of sparkling water.
3. Fill the ice bank in your machine. DSWH160UVPC 1. Unlock and open the side door using the supplied key (A). ENERGY SAVING C A B D 2. Look for the bright yellow label with the arrow (B), which points to the ice bank inlet hole (C). 3. Insert piping from water supply directly into the ice bank inlet. 4. Fill slowly until water starts to come out of the ice bank drainage pipe (D). 5. If you have to move the unit, remember to empty the ice bank first. 6.
DSWH160UVPC Installation and Maintenance Manual 5. Connect external water and CO2 piping. DSWH160UVPC Water input CO2 input 6. Plug the machine into the wall socket and turn it on. 1. Connect the power cable to the nearest socket. 2. Open the front panel with the supplied key and press the power button at the top left of machine (B). DSWH160UVPC B B NOTICE: Chilling of the ice bank begins immediately when unit is turned on. Complete chilling of ice bank will require around 30 minutes - 1 hour.
7. Purge the water lines. 1. Place receptacle beneath tap to catch dispensed water. Discard water as necessary. DSWH160UVPC Press dispensing button 2. Allow water to run continuously until flow is clear of air. 3. Repeat for all taps. NOTICE: The "No/low CO2" error LED will flash when dispensing begins. This is correct, as the CO2 connection has not been activated yet. This alarm can be ignored during this step. 8.
DSWH160UVPC Installation and Maintenance Manual 9. Open the CO2 valve. 1. Using a screwdriver slowly turn valve screw counterclockwise (left) to open valve. 2. Continue until pressure reads 50 to 58 psi max. 10. Re-purge the line for sparkling water. NOTICE: The water will flow flat at first, then gradually become more sparkling as the line is purged of still water. NOTICE: If the "No/low CO2" error LED flashes during this step, there is a problem with the connection to the CO2 source.
Operating the Keypad To dispense your water serving Hold down the button for that dispenser. Note: For safety reason, to dispense hot water you must hold down the upper hot water button first and then the lower hot water/Energy Saving button at the same time. To stop dispensing your water serving Release the button for that dispenser. To turn on Energy Saving mode Press and release for less than 4 seconds the Energy Saving button. Note: The green LED on the right turns on.
DSWH160UVPC Installation and Maintenance Manual Routine Maintenance Daily OO Clean all external surfaces of the machine, the drip tray and the dispensing nozzles. NOTICE: It is recommended that all external components of the product be cleaned daily. It is recommended that you use dish soap, warm water and a clean, soft cloth to clean the product. DO NOT USE THE FOLLOWING PRODUCTS: Do not use ... chlorine bleach solutions on the product.
Annually OO Replace the water filter after 6000 gallons or a maximum of 1 year, or earlier depending on water quality. NOTICE: The filter head has an internal shutoff valve that stops the flow of water when the filter is removed. It is not necessary to shut off the water supply. 1. Turn used filter counterclockwise (to the left) 1/4 turn to remove from filter head. Pull filter away from head and remove. 2. Remove the cap from the new filter. Place the cap on the used filter to seal it. 3.
DSWH160UVPC Installation and Maintenance Manual OO Set the thermostat COLDER 1. Set the thermostat between 5 and 6 to control the temperature of the cold water. 2. If you want to avoid the formation of ice in the bank, turn the thermostat screw located on the back side of the machine at least 1/4 anti-clockwise.
Troubleshooting Problem No water dispense Problem Low flow dispense Problem Sparkling water doesn’t come out Problem Water is not cold enough Problem Hot water is not hot Possible Cause Action To Take The main water valve is closed Open the valve The power switch is set to OFF Set the power switch to ON Malfunction in the ribbon cable connection/ spade connectors Repair connection to main circuit board The water inlet solenoid is not working Bypass the solenoid and replace it The ice bank is
DSWH160UVPC Installation and Maintenance Manual Problem Poor sparkling water quality Problem Slow flashing blue LED (no CO2) alarm on Problem Quick flashing blue LED (no water) alarm on Problem Dripping water Problem Noise/Vibration 22 Possible Cause Action To Take Incorrect air gap in the carbonator Close the CO2 cylinder valve, pull up the ring on safety valve (on the carbonator bowl head) until all air gap is out Use of rinse aid or highly polished glass Avoid excessive use of rinse aid The
Contacting Customer Support Elkay Manufacturing Company 2222 Camden Court Oak Brook, IL 60523 800-726-0553 1000003740 (Rev.
DSWH160UVPC Installation and Maintenance Manual Replacement Parts DSWH160UVPC Part Number Product Name x 1000002622 Motor Fan 120x120x25 x 1000002623 Booster Pump x 1000003891 Main PCB x 1000002625 General Power Switch x 1000002626 Ice Bank Thermostat K55 x 1000002627 Feet 4MA x 1000002629 Submerged Agitator Pump x 1000002631 Inlet Solenoid Valve x 1000003894 Exit Solenoid Valve 2IN-1OUT x 1000003895 Exit Solenoid Vavle (hot) x 1000003896 Flow Control 6mm x 1000003897
1000003740 (Rev.
160219
