DSSBF8S Elkay EZH2O Refrigerated Floor Standing Bottle Filling Station, Filtered INSTALLATION MANUAL (630) 574-8484 Page 1 2000000216 (Rev.
DSSBF8S Contents 1. General Information . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Installation Manual . . . . . . . . . . . . . . . . . . . . . 3 1.2 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.3 Serial Number Location . . . . . . . . . . . . . . . . . 3 1.4 Contact Information . . . . . . . . . . . . . . . . . . . . 3 1.5 Notice of Changes . . . . . . . . . . . . . . . . . . . . . 3 1.6 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. General Information DSSBF8S 1.1 Installation Manual Read all instructions carefully BEFORE starting the installation and familiarize yourself with the various parts of this product. 1.3 Serial Number Location Please use the serial number located on the underside of the water cooler when contacting us with questions concerning the installation of this product. This manual contains step-by-step installation, instructions for the DSSBF8S series bottle filling stations.
DSSBF8S 1.6 Warranty 2. Safety This product is covered by a Limited Warranty and Elkay will not be held responsible for damage of any kind in connection with the installation of the product. THINK SAFETY! Refer to the Elkay website http://www.elkay.com/ warranty and click on drinking water products, 'Warranty for Drinking Water Products' article under the Info and Maintenance section (form 96993C). Think Safety Before performing any work, read and understand the safety instructions in this manual. 2.
2.3 Personal Safety DSSBF8S WARNING These warnings indicate a potentially hazardous situation which, if not avoided, could result in serious injury or death. Follow all instructions related to the installation and/or maintenance of this product (unit). death. Water will conduct electric current to create a short circuit, resulting in injury or death. • Never use electric power tools around water or wet floors/surfaces. • Keep all liquids away from electrical cords and power tools.
Elkay Manufacturing Company Page 6 6-15/16” ( 176mm ) 6-15/16” ( 176mm ) 26-1/8" ( 663mm ) 23-1/16" ( 586mm ) FLOOR LINE 24" (609mm) LONG POWERCORD 1-1/2" (32mm) TAILPIECE TRAP NOT SUPPLIED FILTER LOCATION NOTE: INSURE PRPOER VENTILATION BY MAINTANING 4" (102MM) MINIMUM CLEARANCE FROM THE CABINET LOUVERS TO THE WALL ON EACH SIDE OF THE COOLER 3/8" I.P.S (9.5mm) COLD WATER SUPPLY STUB OUT FROM WALL 1" WATER SUPPLY VALVE BY OTHERS (3/8" OD (9.
DSSBF8S Use Proper Tools Always use proper tools which are in good working condition during the installation of the product. Using tools other than those listed could adversely affect the product and could result in property damage. 3. Tools and Supplies 3.1 Tools Required Tool 2.4 Property Damage Inspect Before Cutting Make sure no electrical wiring or plumbing is present before cutting into a wall.
DSSBF8S 4. Preparation 4.1 General Information 1. This water cooler is designed for indoor use only and should not be installed outdoors or in a humid environment. A water supply pressure below 20 psi will result in decreased water flow through the unit and damage to the product. A pressure above 105 psi will also cause damage to the product. NOTICE 2. Make sure the water supply pressure to the product is between 20 and 105 psi. The filtered units require 40 psi minimum water pressure. 3.
5. Installation of Cooler DSSBF8S 1. Remove the drain access panel by removing the 5/16" hex screws on the rear side of the cooler unit. 4. Take the filter box and drain kit package out of the cooler unit. Note: Filter box and drain kit are packed inside the cooler unit during shipment. Drain Kit Drain Access Panel 2. Position the cooler unit facing front side. Filter Box 5. Attach the nut, the seal, and the elbow tube to the drain outlet and tighten it fully. Elbow Tube Seal Nut 3.
DSSBF8S 7. Remove the top access panel by removing the four phillips screws on the top of the cooler unit using a phillips screwdriver. 11. Use the four phillips screws to install the top access panel on top of the cooler unit. Tighten the four phillips screws fully using a phillips screwdriver. Top Access Panel Top Access Panel Screw Screw 8. Connect the unit water line to shut-off valve. Note: Shut-off valve not shown (installer supplied part). 9.
DSSBF8S 6. Startup 1. Make sure that there are no leaks on the drain connections and installed as per local regulations. 7. Upon initial startup, the plastic bottles saved indicator panel should show several bottles saved due to the water used to initially start up of the unit. 2. Plug-in the water cooler unit. 3. Once power is applied to the bottle filler, the GREEN LED light will illuminate showing good filter status along with the LCD Bottle Counter. 4.
DSSBF8S 7.4 Change the Range Of The IR Sensor 1. Depress the program button when the display reads RNG SET. 2. The display will show the default RNG = 3. 1-10 is the range, 1 is closest to the sensor, 10 is farthest away. 3. Depress the button again to change the value. When the desired range is selected, wait four seconds for the unit to default back to run mode. 4. Test the bottle filler by placing a hand or a bottle in front of the sensor. 7.5 Change the Unit Type 1.
DSSBF8S LIMITED PRODUCT WARRANTY SOFTWARE LICENSE FIRST YEAR - - The Manufacturer warrants every cooler, bottle filling station, packaged water cooler, fountain and accessory to be free from defects in materials and workmanship under normal use for one (1) year from date of install or eighteen (18) months from date of shipment from factory, whichever occurs first.
