Installation manual

M1G Installation and Programming
Page 48
WZnxxx:Selr Prgr
Wireless Zone
WZnxxx 01:=No r
Enable Transmitr
WZnxxx02:=0 r
Supervision Type
WZnxxx 03:=No r
Enable Option 1
WZnxxx 04:=No r
Enable Option 2
WZone = xxx r
TransmtToEnroll
4:KeyfobSelb Prgr
Event Definition
Keyfob Button=1r
1000=Event
2:Xmit Selb Prgr
Transmitter Optr
3:Learn Selb Prgr
WirelessTransmtr
WZone = xxx Push
TransmiterButton
WZnxxx 05:=001 r
Keyfob User ID
Press the RIGHT arrow key to select 2:Xmit Transmitter Opt.
Use the UP and DOWN arrow keys to locate a particular wireless transmitter. Press
the RIGHT arrow key to select and program the displayed transmitter.
This selection determines whether or not the transmitter is enabled. Whenever you
enroll a new transmitter this location will be automatically set to Yes. To permanently
or temporarily disable this transmitter program this to No.
This selection determines the “Supervision Type” for the transmitter. 0=No Supervision,
1=Regular Supervision, 3=Fire Supervision. See receiver selections R02 and R03 for
supervision time values. Default is 1.
This selection corresponds to the Caddx Transmitter Option 1 which deals with
enabling or disabling the internal reed switch on the individual Caddx transmitter so
that an external switch may be hardwired to the transmitter. Refer to the Caddx NX
Series Receiver Instructions, Option 1, for complete details.
This selection corresponds to the Caddx Transmitter Option 2 which deals with
whether an external switch should be normally open (N/O) or normally closed (N/C).
For N/O set option to No. For N/C set option to Yes. Refer to the Caddx NX Series
Receiver Instructions, Option 2, for complete details.
If the transmitter is a keyfob, this sets the User ID to be logged when the keyfob is
used to arm or disarm. Valid range is 001 to 255. Numbers 001 to 099 mirror the
keypad user codes. To report an open/close from a keyfob, program the corresponding
keypad user code to report. A report will be sent regardless of whether it was a user
code or a keyfob that armed/disarmed the system. NOTE: Since there are no open/
close report codes beyond user 99, any keyfob ID that is set higher that 99 will utilize
the opening/closing report code for User 99.
Press the RIGHT arrow key to select 3:Learn Wireless Transmitters.
Press the UP or DOWN arrow keys to locate the wireless zone that you wish to enroll.
Then press the RIGHT arrow key to continue.
Go to the transmitter and press the tamper or enroll button. The keypad should emit a
short tone when the transmitter becomes enrolled.
Press the RIGHT arrow key to select 4:Keyfob Event Definition
Press the UP or DOWN arrow keys to locate the keyfob button to program. There are
a total of 8 programmable buttons, however only 6 of the 8 may be used on the keyfob.
The valid activation events programmable for each button ranges from 0000-0030
(utilizing the Zone Definitions table) and 2001-2032 (utilizing Appendix A, Event Codes).
The standard buttons are as follows: Button 1 (Lock), 2 (Unlock), 3 (Light), and 4
(Asterisk). For Button 7 press a combination of buttons 1 & 2 together at the same
time. For Button 8 press a combination of buttons 3 & 4 together at the same time.
Button 3 on a keyfob can be changed to 5 by setting the transmitter Option 1 to Yes.
Button 4 on a keyfob can be changed to 6 by setting the transmitter Option 2 to Yes.