Installation manual

M1G Installation and Programming
Page 41
Area Report Codes Description of Option
Duress code will be reported if the area is armed or disarmed by a valid user code that is
programmed with the duress attribute. Range is 00 to FF. Default is 00 (no report).
Open After Alarm code will be reported whenever a valid user arrives and disarms the area
following an alarm activation. Range is 00 to FF. Default is 00 (no report).
Open Early code will be reported if the area is disarmed prior to a programmed Expected
Disarm time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).
Fail to Open code will be reported if the area is not disarmed by a programmed Expected
Disarm time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).
Open Late code will be reported if the area is disarmed after a programmed Expected
Disarm time. Refer to the ELK-RP Rules Programming instructions. Range is 00 to FF.
Default is 00 (no report).
Open Keyswitch code will be reported in place of a user code whenever the area is
disarmed by a Keyswitch zone. Range is 00 to FF. Default is 00 (no report).
User Lockout code will be reported if someone repeatedly enters digits (see Menu 07 -
Global System Definitions, Option 12 for the maximum number of digits allowed) in an
attempt to hack out a valid user code. Range is 00 to FF. Default is 00 (no report).
Exit Error Code can be used to identify an accidental alarm caused by an error while
arming. Locally, it works as follows: If an exit delay rolls directly into entry delay as a
result of a zone being left violated, the entry delay warning AND the siren will sound. If the
control is not disarmed prior to the entry delay expiring, the communicator will report the
alarm along with the Exit Error code. Range is 00 to FF. Default is 00 (no report).
Fail to communicate displays on the keypad and the event log when the communicator
fails to complete it’s report using the number of dial attempts. A good communications
report must occur in order to reset/clear the failure. If this fail to communicate report code
is enabled, it will be reported with next good communications to indicate a “past” failure.
Range is 00 to FF. Default is 00 (no report).
AR1 13:Code= 00r
Open Early
AR1 14:Code= 00r
Fail To Open
AR1 15:Code= 00r
Open Late
Menu 09 - Area Reporting Codes (continued)
AR1 16:Code= 00r
Open Keyswitch
AR1 17:Code= 00r
User Lockout
AR1 18:Code= 00r
Exit Error
AR1 19:Code= 00r
Fail Communicate
AR1 11:Code= 00r
Duress Code
AR1 12:Code= 00r
Open After Alrm
Area RCs CID SIA
Alarm Abort 406 O C
Alarm Cancel 406 O C
Automatic Close 403 C A
Early Close 451 C K
Closing Extended 464 C E
Fail To Close 454 C I
Late Close 452 C J
Key Switch Close 409 C S
Duress 121 H A
Area RCs CID SIA
Open After Alarm 450 O R
Early Open 451 O K
Fail To Open 453 O I
Late Open 452 O J
Key Switch Open 409 O S
Keypad Locked Out 461 J A
Exit Error 457 E E
Fail To Communicate 354 R T
Based on the event, the CID (Contact ID) or SIA Codes for Area Reporting Codes will be:
NOTE: On CID reporting the 3 digit code will be preceded by a “1” for a new event or
an opening. It will be preceded by a “3” for a restore or a closing event.