Installation manual

M1G Installation and Programming
Page 28
KP01 03:=No r
Silent on Exit
KP01 04:=No r
Silent on Chime
KP01 05:=No r
Go dark in 60sec
KP01 06:=Yes r
Show Date & Time
KP01 07:=Yes r
Show Temperature
KP01 08:=Yes r
Show Area Name
KP01 09:=No r
Byp Key Req PIN
KP01 01:=1 r
Area Assigned To
Menu 04 - Keypad Definitions
04-Keypad r
Definitions
Keypad Definitions Description of Option
Up to 16 Keypads may be connected. Keypad 1 is the first to display. Press the right
arrow key to program, or press the up or down arrow keys to select another keypad. To
jump to any keypad enter the number (1-16). The keypad name displays on the bottom.
A keypad can only be assigned as primary for a single area. However, it is possible to
“Map” a keypad to another area. Refer to Keypad Menus for instructions. Select which
“primary” area (1 to 8) that the keypad should be assigned. The default value is 1.
If Yes, the keypad will not produce an entry warning signal during entry delay time after
violation of a delay 1 or delay 2 zone while armed. The default value is No.
If Yes, the keypad will not produce an exit warning tone during exit delay 1 or exit delay 2
times upon arming. The default value is No.
If Yes, the keypad will not produce any Chime tone even though the Chime mode may be
on and a chime type zone is violated. This is good for a baby’s room, etc. The default
value is No.
If Yes, the keypad will turn off all backlighting, including Armed or Ready lights, 60 secs.
after arming OR no pushbutton activity. This helps prevent unauthorized viewing of arm/
disarm status through a front glass window or door. Any button press resumes the status
display. The default value is No. NOTE: If any of the F Keys are being used as event
indicators this will also darken them, basically making them non-usable.
If Yes, the keypad will display the date and time on the bottom line of the LCD screen.
Not Available With M1KPAS! If there is too much information to display at once, the
bottom line of the LCD will alternate. The default value is Yes.
If Yes, the keypad will display it’s local temperature on the bottom line of the LCD screen.
Not Available With M1KP2 or M1KPAS! If there is too much information to display at
once, the bottom line of the LCD will alternate. The default value is Yes.
If Yes, the keypad will display the name of the area in which it belongs. If there is too
much information to display at once, the bottom line of the LCD will alternate. Not
Available With M1KPAS! The default value is Yes.
If Yes, the Bypass key cannot be used unless a valid user code is entered. Not
Available With M1KPAS! The default value is No.
KP01 02:=No r
Silent on Entry
KP01: Selb Prgr
Keypad 1
Keypad F1, F2, F3, F4, F5, F6 keys Each keypad has 6 lighted function keys that may be programmed to activate
specific operations. There are 7 programming attributes for each key: 1) KeyEvent - A four digit event code for the zone
definitions 0001 thru 0035, or the automation tasks 2001 - 2032. 2) KeyLight - A four digit event code which lights the
key when the event is active. This can be any of the Appendix A Event Codes. 3) Light Invert - A Yes/No option which
allows the light to be opposite of the event, off when active, on when not. 4) Light Blink - A Yes/No option which allows
the light to blink when active. 5) Key Requires PIN - A Yes/No option used to prevent the key from activating unless a
valid user code is entered. 6) Single Key Press - A Yes/No option which allows a single press of the key instead of the
normal double press to activate the event. NOTE: In the double press mode the key’s name is displayed on the LCD
screen as soon as the first press occurs. This serves to visually verify to the user that the correct key has been
selected prior to the second “activating” key press. 7) Key Name - A sixteen character programmable description that
describes the key’s function. I.E. Police Alarm, Garage Door, etc.
Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.