Datasheet

M2S4G64CB88B5N / M2S8G64CB8HB5N
4GB: 512M x 64 / 8GB: 1024M x 64
PC3-10600 / PC3-12800
Unbuffered DDR3 SO-DIMM
REV 1.0 7
06/2012
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
Environmental Requirements
Symbol
Parameter
Rating
Units
T
OPR
Operating Temperature (ambient)
0 to 85
°C
T
STG
Storage Temperature
-55 to +100
°C
Note: Stress greater than those listed may cause permanent damage to the device. This is a stress rating only, and device functional
operation at or above the conditions indicated is not implied. Exposure to absolute maximum rating conditions for extended periods
may affect reliability.
Absolute Maximum DC Ratings
Symbol
Parameter
Rating
Units
Note
V
DD
Voltage on VDD pins relative to Vss
-0.4 V ~ 1.975 V
V
1, 3
V
DDQ
Voltage on VDDQ pins relative to Vss
-0.4 V ~ 1.975 V
V
1, 3
V
IN
, V
OUT
Voltage on I/O pins relative to Vss
-0.4 V ~ 1.975 V
V
1
T
STG
Storage Temperature
-55 to +100
°C
1, 2
Note:
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability
2. Storage Temperature is the case surface temperature on the center/top side of the DRAM. For the measurement conditions, please refer
to JESD51-2 standard.
3. VDD and VDDQ must be within 300 mV of each other at all times;and VREF must be not greater
Operating temperature Conditions
Symbol
Parameter
Rating
Units
Note
T
OPER
Normal Operating Temperature Range
0 to 85
°C
1, 2
Extended Temperature Range
85 to 95
°C
1, 3
Note:
1. Operating Temperature TOPER is the case surface temperature on the center / top side of the DRAM. For measurement conditions,
please refer to the JEDEC document JESD51-2.
2. The Normal Temperature Range specifies the temperatures where all DRAM specifications will be supported. During operation, the
DRAM case temperature must be maintained between 0 to 85 °C under all operating conditions
3. Some applications require operation of the DRAM in the Extended Temperature Range between 85 °C and 95 °C case temperature. Full
specifications are supported in this range, but the following additional conditions apply:
a) Refresh commands must be doubled in frequency, therefore reducing the Refresh interval tREFI to 3.9 μs. It is also possible to specify
a component with 1X refresh (tREFI to 7.8μs) in the Extended Temperature Range. Please refer to supplier data sheet and/or the
DIMM SPD for option availability.
b) If Self-Refresh operation is required in the Extended Temperature Range, then it is mandatory to either use the Manual Self-Refresh
mode with Extended Temperature Range capability (MR2 A6 = 0b and MR2 A7 = 1b) or enable the optional Auto Self-Refresh mode
(MR2 A6 = 1b and MR2 A7 = 0b). Please refer to the supplier data sheet and/or the DIMM SPD for Auto Self-Refresh option
availability, Extended Temperature Range support and tREFI requirements in the Extended Temperature Range.
DC Electrical Characteristics and Operating Conditions
Symbol
Parameter
Min
Typ
Max
Units
Notes
VDD
Supply Voltage
1.425
1.5
1.575
V
1,2
VDDQ
Output Supply Voltage
1.425
1.5
1.575
V
1,2
Note:
1. Under all conditions VDDQ must be less than or equal to VDD.
2. VDDQ tracks with VDD. AC parameters are measured with VDD and VDDQ tied together.