User Manual 7” Multi Function Pad mPAD2-7-CHT4-I Issue Date: 2017.03.22 v1.
Copyright The documentation and the software included with this product are copyrighted 2009 by ECS(ELITEGROUP COMPUTER SYSTEM) Co., Ltd. All rights are reserved. ECS Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of ECS Co., Ltd.
Warning! Any changes or modifications made to the equipment which are not expressly approved by the relevant standards authority could void your authority to operate the equipment. Attention! Toute modification apportée à l'équipement qui n'est pas expressément approuvé par l'autorité des normes pertinentes peuvent annuler votre droit à faire fonctionner l'équipement. Caution! Danger of explosion if battery is incorrectly replaced.
Packing List Before setting up the system, check that the items listed below are included and in good condition. If any items are missing, please contact your dealer immediately. mPAD2-7-CHT4-I Pad x1 Strap x1 DC Charge Cable x1 HDMI Docking cable x1 USB3.0 Docking cable x1 Docking x1 MSR Module x1 SCR Module x1 Barcode scanner Module x1 USB Ethernet Module x1 Warning! To prevent electric shock, Do not remove cover.
Caution! This adapter Asian Power Devices Inc Type: WA-36A12RU-AAAG is a forming part of the medical device. IE IEC 60417 – 5009 : STAND-BY IEC 60417 – 5031 : Direct Current IEC 60417-5172 : ClassⅡequipment Operation Instructions Safety Instructions Your system is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
1. Do not replace battery yourself. Please contact a qualified technician or your retail provider. Caution! 2 .The computer is provided with a battery-powered real-time clock circuit. There is a danger recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. 1. Ne pas remplacer la batterie vous-même. S'il vous plaît contacter un technicien qualifié Attention! ouvotre fournisseur de détail. 2.
27. Product disposal notice INPORTANT: This symbol if the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products. 28. mPAD2-7-CHT4 product service life is 3 Years. 29. The expected service life of the battery pack is expected to be approximately 3000 cycles.
Contents Chapter 1 General Information ............................1 1.1 1.2 1.3 Introduction .............................................................................................. 2 Medical Application....................................................................................2 Specifications .......................................................................................... 2 Table 1.1:mPAD2-7-CHT4-ISpecification..... 2 Cleaning/Disinfecting .....................................
Chapter 1 1 General Information
1.1 Introduction mPAD2-7-CHT4 is a multimedia Atom Mobile processor-based computer. It is a PC-based system with 7" TFT LCD display and a stereo audio controller. mPAD2-7-CHT4 is a simple, complete and highly integrated mobile multimedia system which allows system integrators to easily build a Mobile Clinical Assistant Terminal into their applications. Common industrial applications include factory automation systems, precision machinery, and production process control.
Camera 8.0 Mega pixel camera with LED light Auto-focus supported Web Camera 2.0 Mega pixel VGA camera Frequency Stability tolerance limit is +/- 20 ppm Power button: On the right side of mPAD2-7-CHT4-M Barcode scanner buttons: On the Top side Control Button Volume control button Home Key button Power LED & Battery status LED Full → Blue Charging → Orange Indicated LED Power Adapter ADP WA-36A12RU-AAAG Input voltage rated: 100-240Vac, 50-60Hz, 1.0-0.
1.4 Cleaning/Disinfecting - During normal use mPAD2-7-CHT4-I may become soiled and should, therefore, be cleaned regularly. Steps: 1. Wipe mPAD2-7-CHT4-I with a clean cloth that has been moistened in the cleaning water. 2. 3. Prepare water per manufacturer’s instructions or hospital protocol. Wipe thoroughly with a clean cloth. Caution! Do not immerse or rinse mPAD2-7-CHT4-I or its peripherals. If you accidentally spill liquid on the device, disconnect the unit from the power source.
1.
Figure 1.
Chapter 2 Getting Started 2
2.1 A Quick Tour of mPAD2-7-CHT4-I Before you start to set up mPAD2-7-CHT4-I, take a moment to become familiar with the locations and purposes of the controls, drives, connections and ports, which are illustrated in the figures below. When placed upright on the desktop, the mPAD2-7-CHT4-I front panel appears as shown in Figure 2.1. Front camera Indicated LED Light sensor Indicated LED Home Key Figure 2.1 Front View The card slots, USB3.0 Port and docking connector are on the Light side of the tablet PC.
The volume control button, Power on button on the right side of the tablet PC. Power Button Volume Button TPU hand holder Hang Hole Figure 2.3 Right Side View The rear view of the tablet PC is depicted in Figure 2.4. Small cover Rear camera Latch for release module device Middle cover Speaker holes Figure 2.
The top side of the tablet PC contains headphone jack. Small cover headphone jack. Figure 2.5 Top View 2.2 A Quick Tour of mPAD-7-CHT4-I Docking Holder (Optional) When you place the docking station on the desktop, its front panel appears as shown in Figure 2.6. Docking connector USB 3.0 Port USB 2.0 Port HDMI Port LAN Port Figure 2.
2.3 Insert the USB Module into the mPAD2-7-CHT4-I TABLET (Optional) Step 1. Removed the small cover Step 2.
2.4 Installation Procedures 2.4.1 Install the Strap (Optional) This strap is designed for the mPAD2-7-CHT4-I, which make the tablet convenient to hold. Figure 2.7 Strap Figure 2.8 Install the Strap 2.4.2 Insert / Hang the Stylus Pen (Optional) Figure 2.
a. Hang and secure the stylus Pen through the hang hole of the mPAD2-7-CHT4-I b. Insert and secure the stylus Pen onto the strap. Figure 2.10 Secure the stylus Pen. 2.4.3 Insert the mPAD2-7-CHT4-I into the Docking Station (Optional) 1. Open and turn the protective cover of the docking port to the opposite side and press to lock it into its reserved slot. Figure 2.11 Open and secure the protective cover 2.
2.4.4 Connecting the Power Cord for the Docking Station Be sure to always handle the power cords by holding the plug ends only. Follow these procedures in order: 1. Insert the mPAD2-7-CHT4-I into the docking station as previous section 2.3.3.(See Figure 2.13). 2. Connect the female end of the power cord to the DC-in jack of the docking station. 3. Connect the 2-pin male plug of the power cord to an electrical outlet. DC-Jack Port Step 3 Step 2 Figure 2.
2.4.5 Warning information for table use. 2.4.5.1 Connect to HDMI monitor Figure 2.14 when table put into Dock. When table put into Dock, Connect to HMDI monitor, the display will not show full screen on first time, please restart operation system, it will be normal. 2.4.5.2 Precautions for use with output port 1. Connect dock port only, please use usb2.0 device or usb3.0 device. 2. Connect usb3.0 port only, please use usb2.0 device or usb3.0 device. 3. Connect dock port and usb3.
Chapter 2 3 EMC TEST REPORT TE
Chapter 3 EMC TEST REPORT 3.1 Description of Standards and Results for EN55022/EN55024 EMISSION Description of Test Item Standard Conducted disturbance CISPR 11:2009+A1:2010 EN 55011:2009+A1:2010 Radiated disturbance (30-1000MHz) CISPR 11:2009+A1:2010 EN 55011:2009+A1:2010 Limits Results Group 2, Class B PASS Minimum passing margin is 6.69dB at 0.158MHz Group 2, Class B Radiated disturbance (Above 1GHz) CISPR 11:2009+A1:2010 EN 55011:2009+ PASS Minimum passing margin is 3.10dB at 593.
Chapter Troubleshooting 4
Chapter 4 Troubleshooting After Power on the TABLET for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips. 4.1 Solving Problems Follow these tips when you troubleshoot your computer: • If you added or removed a part before the problem started, review the installation procedures and ensure that the part is correctly installed.
4.3 Troubleshooting Audio Problems Problem: No sound from integrated speakers. Troubleshooting and problem resolution: • Adjust the windows volume control — Double-click the speaker icon in the lower-right corner of your screen. Ensure that the volume is turned up and that the sound is not muted. Adjust the volume, bass, or treble controls to eliminate distortion. • Reinstall the audio driver.
