User Manual 7” Multi Function Pad mPAD-7-CHT3-I
Copyright The documentation and the software included with this product are copyrighted 2009 by ECS(ELITEGROUP COMPUTER SYSTEM) Co., Ltd. All rights are reserved. ECS Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of ECS Co., Ltd.
Warning! Any changes or modifications made to the equipment which are not expressly approved by the relevant standards authority could void your authority to operate the equipment. Attention! Toute modification apportée à l'équipement qui n'est pas expressément approuvé par l'autorité des normes pertinentes peuvent annuler votre droit à faire fonctionner l'équipement. Caution! Danger of explosion if battery is incorrectly replaced.
Packing List Before setting up the system, check that the items listed below are included and in good condition. If any items are missing, please contact your dealer immediately. mPAD-7-CHT3-I Pad x1 Strap x1 Stylus pen x1 HDMI Docking cable x1 USB3.0 Docking cable x1 Docking Holder x1 Docking Power adapter x1 Software CD (Drivers and Utility, Manual) Warning! To prevent electric shock, Do not remove cover. No user serviceable parts inside, refer servicing to qualified personnel.
Safety Instructions 1. 2. 3. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. 6. Keep this equipment away from humidity. Put this equipment on a reliable surface during installation.
17. 18. 19. 20. 21. IMPROPER INSTALLATION OF VESA MOUNTING CAN RESULT IN SERIOUS PERSONAL INJURY! VESA mount installation should be performed by a professional technician; please contact the service technician or your retailer if you need this service. CLASSIFICATION: Supply Class I adapter No applied part IP54 Continuous Operation Not AP or APG category Disconnect device: Appliance inlet. Follow national, state or local requirements to dispose of unit.
mPAD-7-CHT3-I Tablet PC User Manual vi
Contents Chapter 1 1.1 1.2 1.3 1.4 Chapter General Information ............................1 Introduction .............................................................................................. Specifications .......................................................................................... Table 1.1:mPAD-7-CHT3-ISpecification..... Cleaning/Disinfecting ............................................................................... Dimensions ...............................................
mPAD-7-CHT3-I Tablet PC User Manual
Chapter 1 1 General Information
1.1 Introduction mPAD-7-CHT3-I is a multimedia Atom Mobile processor-based computer. It is a PC-based system with 7" TFT LCD display and a stereo audio controller. mPAD-7-CHT3-I is a simple, complete and highly integrated mobile multimedia system which allows system integrators to easily build a Mobile Clinical Assistant Terminal into their applications. Common industrial applications include factory automation systems, precision machinery, and production process control.
Web Camera Control Button 2.0 Mega pixel VGA camera Power button: On the top side of mPAD-7-CHT3-I Barcode scanner buttons: Two orange buttons Volume control button Home Key button Programmable button (Default setting): - P1 for S3 mode P2 for WiFi on/off Indicated LED Power LED & Battery status LED Full → Blue Charging → Orange Power Adapter EDAC EA1024CR-050 Input voltage rated: 100-240Vac, 50-60Hz, 1.
1.3 Cleaning/Disinfecting - During normal use mPAD-7-CHT3-I may become soiled and should, therefore, be cleaned regularly. Steps: 1. Wipe mPAD-7-CHT3-I with a clean cloth that has been moistened in the cleaning solution. 2. 3. Prepare agent per manufacturer’s instructions or hospital protocol. Wipe thoroughly with a clean cloth. Caution! Do not immerse or rinse mPAD-7-CHT3-I or its peripherals. If you accidentally spill liquid on the device, disconnect the unit from the power source.
1.4 Dimensions 121mm 200mm Figure 1.
Chapter 2 Getting Started 2
2.1 A Quick Tour of mPAD-7-CHT3-I Before you start to set up mPAD-7-CHT3-I, take a moment to become familiar with the locations and purposes of the controls, drives, connections and ports, which are illustrated in the figures below. When placed upright on the desktop, the mPAD-7-CHT3-I front panel appears as shown in Figure 2.1. LED indicator Ambient sensor Camera Home Key Figure 2.1 Front View The volume control button, barcode scanner button and docking connector are on the left side of the tablet PC.
The card slots, barcode scanner button and programmable buttons are on the right side of the tablet PC. Card Slots (Micro SD) Barcode scanner button Programmable key Hang hole Figure 2.3 Right Side View The rear view of the tablet PC is depicted in Figure 2.4. Camera Speaker Camera flash Figure 2.
The top side of the tablet PC contains power button, barcode scanner and headphone jack. Figure 2.5 Top View 2.2 A Quick Tour of mPAD-7-CHT3-I Docking Holder (Optional) When you place the docking station on the desktop, its front panel appears as shown in Figure 2.6. Docking connector Figure 2.6 Front View USB 3.0 USB 2.0 HDMI port port ports LAN port DC in jack Figure 2.
2.3 Installation Procedures 2.3.1 Install the Strap (Optional) This strap is designed for the mPAD-7-CHT3-I, which make the tablet convenient to hold. Figure 2.8 Strap a. Aim the triangle mark on the strap to the home key to slightly insert the bottom side of the tablet into the strap. b. Press to insert the top side of tablet into the strap. Figure 2.9 Install the Strap 2.3.2 Insert / Hang the Stylus (Optional) Figure 2.
a. Hang and secure the stylus through the hang hole of the mPAD-7-CHT3-I. b. Insert and secure the stylus onto the strap. Figure 2.11 Secure the stylus 2.3.3 Insert the mPAD-7-CHT3-I into the Docking Station (Optional) 2. Open and turn the protective cover of the docking port to the opposite side and press to lock it into its reserved slot. Figure 2.12 Open and secure the protective cover 1.
2.3.4 Connecting the Power Cord for the Docking Station Be sure to always handle the power cords by holding the plug ends only. Follow these procedures in order: 1. Insert the mPAD-7-CHT3-I into the docking station as previous section 2.3.3.(See Figure 2.13). 2. Connect the female end of the power cord to the DC-in jack of the docking station. 3. Connect the 2-pin male plug of the power cord to an electrical outlet. Step 2 Step 3 Figure 2.
www.ecs.com.tw This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © ELITEGROUP COMPUTER SYSTEM Co., Ltd.
