Folding Presentation Screen QuickStand Series Users Guide
Setup Procedure The frame and supports are made of 1 3/8” aluminum tubing with an anodized finish. Please follow the instructions in this package. With proper care, your QuickFold screen will provide many years of reliable service. Two Section Frame (For presentation screens that are less than 120” in diagonal measurement) 1. Take the frame out of the case and remove its wrappings. Unfold the main joints as shown in (fig 1). 2.
Three Section Frame (For large presentation screens that are 120” or more in diagonal measurement) 1. Take the frame out of the case and remove its wrappings. Unfold the main joints making sure that both the end and middle spans are in prefect alignment as shown in (fig 4). 2. Make sure that the snap latches have locked the joints in the frame so that it is at its full horizontal extension as shown in (fig 5) 3.
Standard T-Leg Support 1. Take the T-Leg out of the case and remove its wrappings. Fold down the support legs as shown in (fig 7). 2. Secure the corner braces into the locked position as shown in (fig 8) 3. Unfold the T-Leg’s main support until the snap latches “click” into the locked position as in (fig 9).
快折幕腿架方法順序 `圖 1 、2、3 腿架展開。注意夾傷，夾物 Following steps 1,2,3 below, use caution during attachment. 展開 unfold 圖 2、3 滑道是來調解杆的長短，最後用 鬆緊調解頭鬆緊 Fig2 ,3 adjust the height of the frame and then tighten the connection screws.
Attaching the Frame to its Supports 1. Always use at least two locking bolts through the T-Leg Support, the Spacer and into the Frame on each side. 2. Height can be adjusted in 8” increments up or down. Normal screen height is 44” from the bottom of the frame to the floor. 3. Reverse this process to dismantle and pack away the screen.
1. With the viewing surface facing up, fold the fabric in half from top to bottom. When folding, make certain that the viewing surface does not come into contact with the black binding, grommets or snap buttons. *Note: The screens are shipped from production with tissue paper in the folds that should be retained for future use. 2. It is preferable to make sure that the first folds never exceed 3 feet in width (fold again if necessary).
Packing List 1. 2. 3. 4. 5. 6. 7. 8. Frame 1 piece Support (T) Legs 2 pieces AT-Legs 2 pieces (optional depending on size) SAT-Legs 2 pieces. (optional depending on size) Screen Fabric 1-2 pieces Locking Bolt 6-26 pieces Frame Spacer 6-26 pieces Manual 1 piece The following points should be noted to assure satisfactory performance and longevity of your screen 1. Never use your exposed hand to touch the screen surface because of grease from the skin. 2. Never scrabble on the screen with anything. 3.
US and Canada Warranty Policy – Two (2) year warranty parts and labor from purchase date as follows (except for refurbished units as specified below): • Refurbished units carry a 90-day parts and labor warranty. • Demo units or open box items are AS IS items and do not carry a warranty. • Each party will be responsible for one way shipping during the warranty period. • DOA (Defective On Arrival): Must be reported within 7 business days of receipt.
REMEMBER TO REGISTER YOUR WARRANTY AT WWW.ELITESCREENS.COM/REGISTER.HTM US & Canada Tech Support & Warranty Claim Please contact us at service@elitescreens.com or call +1 877-511-1211 #3 Service Europe Tech Support & Warranty Claim Please contact us at service@elitescreens.eu or call +49-(0) 40-30392958 Asia Tech Support & Warranty Claim Please contact us at service@elitescreens.com.
