User Guide

ManualsBrandsElite Screens ManualsElectronicsYardmaster 2 Dual Projector Screen, 100-INCH 16:9, Front and Rear Wraith Veil Dual 4K / 8K Ultra HD, Active 3D, HDR Ready Indoor and Outdoor Projection Screen, OMS100H2-Dual…

Rev.011817-DR www.elitescreens.com 1

Yard Master 2 Dual Series

Indoor/Outdoor Portable Projection Screen

User’s Guide

Thank you for choosing the Yard Master 2 Dual portable projection screen! Please read through this user

guide before utilizing the screen. Correct usage and maintenance will ensure a long product life.

Care & Use Instructions

◆The WraithVeil Dual is a 2-directional flexible vinyl projection screen material. It is designed to

accommodate either front or rear projection.

◆ Be sure to use the screen only during a light breeze; it is not meant to withstand heavy winds. *Elite

Screens is not responsible for damages due to negligence resulting from misuse under weather

conditions and will void your warranty.

◆Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the

points below to prevent that from occurring:

1. Do not touch the projection surface with your hands

2. Do not write or draw on the projection surface

3. Do not use fingers or sharp objects to point on the projection surface; this will damage the

screen material.

4. Use a soft-damp cloth to clean the projection surface; do not use chemical cleaning agents or

alcohol.

5. Use clean water when dampening the cleaning cloth and do not rub against the material to

clean it.

◆After using the screen, disassemble it and store it in the carrying bag provided.

◆To avoid damage and injury, the screen should only be operated by adults.

Product Description

Design: The aluminum frame is designed to be light weight and easily operated making it easy to carry,

assemble and disassemble.

Summary of content (6 pages)

PAGE 1
Yard Master 2 Dual Series Indoor/Outdoor Portable Projection Screen User’s Guide Thank you for choosing the Yard Master 2 Dual portable projection screen! Please read through this user guide before utilizing the screen. Correct usage and maintenance will ensure a long product life. Care & Use Instructions ◆The WraithVeil Dual is a 2-directional flexible vinyl projection screen material. It is designed to accommodate either front or rear projection.
PAGE 2
Screen Fabric: The screen fabric is attached to the rectangular frame and held in place by several press studs, which ensure an evenly stretched and flat surface. The WraithVeil Dual screen material is durable and can be folded many times without causing damage or distortion to the surface. Parts Diagram A. Folding frame x1 B. Left and right folding legs x2 D. Projection screen material x1 E. Knob screw x2 G. Rope x2 C. Screen material bag x1 H. Carrying Bag x1 F. Eyebolt x2 I.
PAGE 3
2. Unfold the frame until the latch on the hinge "clicks" into place. Repeat the procedure for the shorter sections. (Fig. 5-6) Fig. 6 Fig. 5 3. Make sure all 4 corners of the frame are at a 90° angle and the hinged support bar is straight and not bending. (Fig. 7-9) Fig.7 Fig.8 Fig.9 4．Insert the frame legs (B) into the openings located at the left and right bottom sides of the folding frame (A). Secure them by fastening the knob screw (E) into the adjacent hole.
PAGE 4
H A D Fig.15 E G C Fig14 B F Fig.13 7. Tie 4 pieces of rope (2 on the left and 2 on the right) to the eyebolts (F) that are located at the top of the frame. Next, lift the screen up while simultaneously opening the frame legs. Two people are needed for this step. Fig.16-17. Fig.16 Fig.17 8. To secure the frame, place a stake (I) into each hole located on the frame footing, and hammer it into the ground.
PAGE 5
1. Remove ropes (G) and stakes (I) from the ground. 2. Unlatch the hinged support bars on front side of each leg so that it is bent and fold that half of the legs up for the next step. 3. Slowly lower the screen to the ground (towards the closed legs). Two people are needed for this step. 4. Unlatch the hinged support bars and fold down other half of legs. 5. Loosen and remove the ropes, knob screws (E) and eyebolts (F) from each leg. 6. Remove the frame legs (B) from the folding frame (A). 7.
PAGE 6
9. Unlatch the hinged support bars in each corner of the folding frame (A). 10. Press in the silver locking buttons, near the folding joints, and slowly gather the sides of the folding frame. 11. Again, press in the silver locking buttons. Then, pick up one end of the folding frame, and walk it to the other end, folding the longer sections into thirds. 12. Store the screen in the provided carrying bag (h).