Fixed F F Frame P Projectio on Screeen Cin nem ma23 35 Seri S ies User’s Guide 1 Rev.051811‐A AS www.elitescrreens.com info@ @elitescreens.
Parts List for the Cinema235 Series Please make sure all parts listed below are included before proceeding with the installation. 1. Frame Parts x 6 pcs (4 Top & Bottom frame pcs + 2 Side frame pcs) 2. Tension Rods x 6 pcs (4 Top & Bottom frame rods + 2 Side rods) 3. Screen Material x 1 pc 4. Center Joints x 2 pcs 5. Elbow Joints x 4 pcs 6. Wall Brackets x 2‐3 pcs (depending on size) 7. Screws x 16 pcs 8. User Guide x 1 pc 9. Center Support Bar x 1‐2 pcs (depending on size) 10.
2. Insert the other horizontal frame piece to the Center Joint connector and secure with screws. Push 1/2Long frame Note: To make sure the frame pieces line up correctly, do not tighten the screws until assembly is complete. 3. Insert both Elbow Joint connectors into the long horizontal frame (see fig. 1). Long frame Push Push Joint ( fig.1) P ush P ush S h o rt fra m e S h o rt fra m e 3 Rev.051811‐AS www.elitescreens.com info@elitescreens.
. Join all four frame parts together following the steps showed below (see fig. 2) Insert the exposed ends of the joint connectors into the short (vertical) frame and align the four corners so that they meet at perfect right angles Push Push ( fig.2) 5. Make sure all four corners join correctly to form a perfect rectangle, then fasten the four angles together by using the included joint screws. (see fig. 3) Screw ( fig.3) 4 Rev.051811‐AS www.elitescreens.com info@elitescreens.
Attach the Screen Material to the Frame 1. Lay out the material and Tension Rods on a clean & dry surface. Insert the Tension Rods through the sleeves according to their corresponding lengths on each edge of the screen (see fig. 4). Tension Rod (Horizontal) x 4 Tension Rod (Vertical) x 2 Screen Push Steel rod Steel rod Push ( fig.4) 2. Place the screen material on the back of the frame and insert the tension rods into the grooves running of each corner of the frame.
Black Backing for AcousticPro1080 Models This procedure only applies to models with AcousticPro 1080 Material. The Black Backing counters the effects of light penetration that would otherwise light up all items behind the screen and spoil the picture. Attach the Black Backing behind the projection surface and secure to the Velcro‐Faced Fix Plates. Black backing Fix plate secures AcousticPro1080 material and the black backing behind it.
Attach the Fix Plates 1. Make sure that the material and frame are both lying face down on a clean, dry and non‐abrasive surface. 2. Center the material inside of the frame Note: The material was made smaller than the frame in order to be stretched to create a sufficient amount of tension. 3. Start attaching the Fix Plates in the center of each horizontal frame piece (1), then in the center of each vertical frame piece (2). (see fig.
3. Slide the top end of the bar into the top center point location to complete the installation. This will provide stability to the frame and tension to the material. Center Support Bar (Fig. 8) Installation 1. Elite recommends using a stud finder (not included) to locate and mark the installation location. 2. Drill a hole with the proper bit size according to the included wood screws. 3. Line‐up the Wall Brackets with the drilled holes and screw them in using a Phillips screw driver.
Caution Please follow these instructions carefully to ensure proper maintenance and safety with your Cinema235 Screen. 1. When hanging the screen up, please make sure that no other objects such as power switches, outlets, furniture, ladders, windows, etc. occupy the space designated for your Fixed‐Frame screen. 2.
Cinemaa235 Diimensioon Tablee 1 Measurements are inten nded as a referencee only and are sub bject to change without notice. Notee: Data Error may be ±1" 10 Rev.051811‐A AS www.elitescrreens.com info@ @elitescreens.
Warranty Policy • • • • • • • • Two (2) Year parts and labor warranty from defects in workmanship from purchase date as follows (except for refurbished units as specified below). Three (3) Year parts and labor warranty from defects in workmanship for GEMR (Government, Educational, Military, & Religious) purchases of new product only. Refurbished Units carry a 90‐DAY parts and labor warranty. Each party will be responsible for one way shipping during the warranty period.
Contact Info US & Canada Tech Support & Warranty Claim Please contact us at service@elitescreens.com or call +1 877‐511‐1211 #3 or fax +1‐562‐926‐8433 Europe Tech Support & Warranty Claim Please contact us at service@elitescreens.eu or call +49‐(0) 40‐30392958 Asia Tech Support & Warranty Claim Please contact us at service@elitescreens.com.cn or call +86‐(0) 755‐8461‐7989 Taiwan Tech Support & Warranty Claim Please contact us at service@elitescreens.com.
