Specifications

ManualsBrandsElite access systems ManualsGate OpenerMiracle-One

TABLE OF CONTENTS…………………………………………………………

UL LISTINGS AND INSTRUCTIONS……………………………………………

WARNINGS AND PRECAUTIONS………………………………………………

PROCEDURE FOR INSTALLATION………………………………………………

CONTROL BOARD BOX & HOW TO REMOVE CONTROL BOARD………………

CONNECTING POWER……………………………………………………………

CONNECTING POWER MASTER / SLAVE…………………………………………

CHOOSING MOVEMENT DIRECTION……………………………………………

CURRENT SENSOR ADJUSTMENT………………………………………………

POWER SUPPLY…………………………………………………………………

DRY CONTACT & RECEIVER WIRING………………………………………………

SAFETY AND CENTER LOOP INSTALLATION ………………………………………

PHOTO CELL INSTALLATION………………………………………………………

CONTROL BOARD DESCRIPTION…………………………………………………

CONTROL BOARD DESCRIPTION MASTER / SLAVE ………………………………

MAGLOCK & ALARM CONNECTORS ………………………………………………

BURGLAR ALARM …………………………………………………………………

GATE OPENING INSIDE INSTALLATION ……………………………………………

GATE OPENING OUTSIDE INSTALLATION……………………………………………

EMERGENCY KEY RELEASE…………………………………………………………

CLOSE DELAY OPTION (MASTER / SLAVE ONLY) OPENING INSIDE………………

CLOSE DELAY OPTION (MASTER / SLAVE ONLY) OPENING OUTSIDE …………

TROUBLESHOOTING……………………………………………………………

MIRACLE•1 PARTS LIST …………………………………………………………

FEATURES AND SPECIFICATIONS …………………………………………………

4-5

7-11

29-30

Do not

touch me

unless you are an

authorized service

technician!

Handbook may be reproduced by any

means without the expressed written

permission of the publisher. Materials,

components and specifications are

subject to change without notice.

RELEASE 1

TABLE OF CONTENTS

CLICK THE TOPIC OF YOUR CHOICE

ATTENTION: This handbook is exclusively for qualified installation personal, and assistance

and/or maintenance service. - The performances indicated in this handbook are valid only if

a correct assembly has been carried out.

Summary of content (32 pages)

PAGE 1
T A B L E O F C O N T E N T S ATTENTION: This handbook is exclusively for qualified installation personal, and assistance and/or maintenance service. - The performances indicated in this handbook are valid only if a correct assembly has been carried out.
PAGE 2
UL LISTINGS AND INSTRUCTIONS INSTALLATION INSTRUCTIONS REGARDING THE GATE OPERATOR A) Install the gate operator only when: 1) The operator is appropriate for the construction and the usage Class of the gate. 2) All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of 4 feet (1.2 m) above the ground to prevent a 2 1/4inch (57.
PAGE 3
UL LISTINGS AND INSTRUCTIONS H) For a gate operator utilizing a non-contact sensor such as a photo beam: 1) See instructions on the placement of non-contact sensor for each Type of application, 2) Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate still moving, and 3) One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the perimeter reachable by a moving gate or barrier.
PAGE 4
UL LISTINGS AND INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS WARNING - To reduce the risk of injury or death: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children operate or play with gate controls. Keep the remote control away from children. 3. Always keep people and objects away from the gate while the gate is in operation. NO ONE SHOULD CROSS THE PATH OF A MOVING GATE. 4. Test the gate operator monthly.
PAGE 5
UL LISTINGS AND INSTRUCTIONS Gate – A moving barrier such as a swinging, sliding, raising lowering, rolling, or like, barrier, that is a stand-alone passage barrier or is that portion of a wall or fence system that controls entrance and/or egress by persons or vehicles and completes the perimeter of a defined area.
PAGE 6
WARNINGS AND PRECAUTIONS WARNING: TO REDUCE THE RISK OF INJURY TO PERSONS THE MIRACLE•1 IS FOR VEHICULAR GATE USE ONLY Be sure to read and follow all these important instructions before installation of the gate operator. Elite Access Systems, Inc. is not responsible for improper installations or failure to comply with local building and electrical codes. Not for installation on any pedestrian gates. Not for installation on any pedestrian passages or doorways.
PAGE 7
P R O C E D U R E F O R I N S T A L L AT I O N O p e n To T h e I n s i d e 10.5” 8.5” 25.75” 7.
PAGE 8
P R O C E D U R E F O R I N S T A L L AT I O N O p e n To T h e O u t s i d e Indexing on Central Hole Indexing on Mounting Hole BACK TO TA B L E OF CONTENTS
PAGE 9
P R O C E D U R E F O R I N S TA L L AT I O N ( c o n t . ) F STEP 1: Remove the cover - E - by removing 4 screws. STEP 2: Release the mechanical lock by turning Key - F - to the horizontal position. STEP 3: Position and level the operator brackets and plates (SEE BELOW AND PAGE 3). Tack weld plate and brackets in position. With gate closed, position the plates on the gate taking care that the operator is kept level.
PAGE 10
P R O C E D U R E F O R I N S TA L L AT I O N ( c o n t . ) STEP 4: Remove operator and fully weld the plate and brackets top, bottom and sides. CAUTION: WELDING WITH OPERATOR IN PLACE MAY DAMAGE THE OPERATOR. STEP 5: MAKE SURE THE OPERATOR IS LEVEL or the operator will not function properly. An off-level installation may cause the gate or operator to fail prematurely. c. a. b. STEP 6: Remove bolt and bushing from back of operator.
PAGE 11
P R O C E D U R E F O R I N S T A L L AT I O N ( c o n t . ) F STEP 9: Carry out all appropriate connections in the following pages of the manual to power the unit. Then go to step 10. STEP 8: Lock the operator by turning key - F - to the vertical position while pushing or pulling on the gate until you hear the key release click into place. STEP 10: Adjust the traveling distance with the outside limit switch of each set. Outside Switch Inside Switches Outside Switch STEP 11: Re-install the cover.
PAGE 12
REMOVING THE CONTROL BOARD J1 J3 Detach the J1 and J3 plug . Remove the three, phillips head screws and remove control board. Reverse this process to install the control board. MOUNTING THE CONTROL BOX CAUTION: Do not make new mounting holes, or enlarge existing holes in control box. Use the four mounting holes provided. Remove the four nuts and remove battery rack. Reverse this process to reinstall.
PAGE 13
CONNECTING POWER CAUTION: Do not over-bend the wire connection from the operator. To do so will cause the wires to eventually break. IMPORTANT: Be sure to install the Flex Connector (supplied) to secure the wire in the Miracle-1 Control Board Box.
PAGE 14
CONNECTING POWER Master / Slave IMPORTANT: Be sure to install the Flex Connector (supplied) to secure the wires in the Miracle-1 Control Board Box. CAUTION: Do not over-bend the wire connections from the operators. To do so will cause the wires to eventually break.
PAGE 15
CHOOSING MOVEMENT DIRECTION Switch the “Open Inside / Open Outside” switch on the control board to the corresponding position for the proper direction. OPEN INSIDE OPEN OUTSIDE SENSOR ADJUSTMENT The sensors must be adjusted while the gate is in the opening or closing cycle. Set the sensor adjustment so when the gate hits any object while opening, it will stop and when the gate hits any object while closing, it will reverse.
PAGE 16
P O W E R S U P P LY Use the plug-in transformer (sold by Elite Access System only) by hooking it up to 115V and use Two Conductor, low voltage, 14 gauge / 300 watt direct burial, landscape lighting cables (part #A W-100 or A W-500). Connect these wires to the two yellow wires from operator connector(J3), to the plug-in transformer. Connect the battery cable to the harness connector from J1. The Timer LED will blink 3 times. After the blinks, check the “charge ok” LED, it must be on.
PAGE 17
D R Y C O N TA C T & R E C E I V E R W I R I N G BACK TO TA B L E OF CONTENTS
PAGE 18
S A F E T Y & C E N T E R L O O P I N S T A L L AT I O N BACK TO TA B L E OF CONTENTS
PAGE 19
P H O T O C E L L I N S T A L L AT I O N To reduce the risk of injury, Elite HIGHLY RECOMMENDS installing a PHOTOCELL SENSOR when the gate opens to less than 18” from a wall or any other object. Follow the installation instructions provided with the PHOTOCELL SENSOR for accurate placement of the PHOTOCELL and the REFLECTOR.
PAGE 20
CONTROL BOARD DESCRIPTION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Open or Close Relay LED Control Relay LED Motor Fuse J1-Batteries and Motor Connector Strike Open LED Safety Loop LED Radio Receiver LED Center Loop LED J3 Transformer & Input Commands Connector Central Control LED Batteries Low LED Charger Ok LED Power LED Charging Power Fuse BACK TO TA B L E 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27.
PAGE 21
CONTROL BOARD DESCRIPTION Master / Slave 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Open or Close Relay LED Control Relay LED Motor Fuse J1-Batteries and Motor Connector Strike Open LED Safety Loop LED Radio Receiver LED Center Loop LED J3 Transformer & Input Commands Connector Central Control LED Charging Power Fuse Board Fuse Replace Charging Power Fuse LED Replace Board Fuse LED BACK TO TA B L E 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28.
PAGE 22
MAGLOCK & ALARM CONNECTORS Contact Data Contact Rating 125 VAC - 0.5 A Use the harness provided with the unit to make your connections to these alarm outputs.
PAGE 23
BURGLAR ALARM .. . HO US E A LA R M USE LOW VOLTAGE WIRE 20 AWG IMPORTANT: When interfacing with a house alarm you must install positive stops at the gate closed position.
PAGE 24
G A T E O P E N I N G I N S I D E I N S T A L L A T I O N O F. . .
PAGE 25
G A T E O P E N I N G O U T S I D E I N S T A L L A T I O N O F. . .
PAGE 26
EMERGENCY KEY RELEASE To move the gate during an emergency or power failure, insert the key (step 1) into the key release hole on the front of the operator. Turn the key counterclockwise to release the gate. Move the gate manually (step 2) to the full open position. STEP 1 UNLOCK KEY (PROVIDED) STEP 2 90° STEP 3 RE-LOCK Re-lock the operator (step 3) by turning the key release clockwise while pushing or pulling on the gate until you hear the key release click into place.
PAGE 27
C L O S E D E L AY O P T I O N (Master / Slave only) This option is to be used when there is an master/slave installation with overlapping gates. OPENING INSIDE & OVERLAPPING TO THE OUTSIDE... OPENING INSIDE & OVERLAPPING TO THE INSIDE...
PAGE 28
C L O S E D E L AY O P T I O N (Master / Slave only) This option is to be used when there is an master/slave installation with overlapping gates. OPENING OUTSIDE & OVERLAPPING TO THE OUTSIDE... OPENING OUTSIDE & OVERLAPPING TO THE INSIDE...
PAGE 29
TROUBLESHOOTING Check the fuses If the gate is not moving in any direction be sure to check all of the LED displays on the control board. If the board power or charging power LEDs are on, change the corresponding fuse on the right side of the board.
PAGE 30
TROUBLESHOOTING Checking Control Options (example - Radio Receiver) Problem: The radio receiver LED is on and the gate remains open. Problem: The radio receiver LED is not on and the gate will not open with the radio receiver. Solution: The radio receiver has malfunctioned in the "OFF" position. Solution: The radio receiver has malfunctioned in the "ON" position You will see the alarm sensor LED on when 1. The gate is too heavy or the arm is installed wrong. 2.
PAGE 31
M I R A C L E • 1 PA RT S L I S T 1 5 3C 3B 6 2 9 3A 10 8A 11 7 8B 4 1 - Control Board Screws (Set) Q006 2 - Control Board Q222, Q223 3A - Backup Batteries A BT MIR 3B - Battery Rack 3C - Battery Rack Nuts (Set) 4 - Operator Q221 5 - Control Board Box Q227 6 - Cover Q228 7 - Key Release Q257 8A - Front Mounting Plate Q230, 8B - Back Mounting Plate Q230 9 - Motor Harness Q224, Q226 10 - Accessory Harness Q231 11 - Transformer A POW 3 Alarm Harness Q242 8 Amp Fuse Q243 Limit Switch Harness Q239 Mag L
PAGE 32
F E AT U R E S A N D S P E C I F I C AT I O N S MECHANICAL SPECIFICATIONS Overall Dimensions MOTOR - 24V DC, 12 Amps. CYCLES - 100 / Day. SHIPPING WEIGHT: Single Unit: 58 lbs. - Master/Slave: 89 lbs TORQUE - 600 lbs. of torque. FINISHING - Aluminum. DIMENSIONS - L 39 1/2”, W 3 1/2”, H 4". CAPABILITIES - Maximum gate size 15' wide, 600 lbs. OPERATOR TRAVEL SPEED - 14 to 18 seconds 90° opening. ELECTRICAL SPECIFICATIONS RUNNING SYSTEM - Microcontroller with built-in watchdog system.