LeadTech Crop.
Linux DVR System Copyright ⓒ 2003 LeadTech Corp. All rights reserved. The contents of this User’s Manual shall not be reproduced arbitrarily without prior approval. The product of this User’s Manual may be modified without advance notice for the reasons of upgrading, etc. The trademarks mentioned in this User’s Manual are registered trademark and unique trademark of each relevant company.
Linux DVR System This User’s Manual contains the following contents. Matters to note in installing ELiSS LD-1600 Name and function of each part of ELiSS LD-1600 Method of installation of ELiSS LD-1600 and connection of related equipment Method of using and setting of ELiSS LD-1600 Product specifications of ELiSS LD-1600 Repair of trouble and checking procedures, etc.
Linux DVR System Contents of User’s Manual I . MATTERS TO BE NOTED.......................................................................................................９ II . COMPOSITION OF ELISS LD-1600 PRODUCT ............................................................... １０ III . MAJOR FEATURES OF ELISS LD-1600.......................................................................... １１ IV . FUNCTION OF ELISS LD-1600 .....................................................................................
Linux DVR System 2.7. Conversion of camera channel from DISPLAY MODE screen ...................................... ２２ 2.7.1. Conversion of Camera Channel from Screen Divided into 9 ...............................................２３ 2.7.2. Conversion of Camera Channel from Screen Divided into 8 ...............................................２４ 2.7.3. Conversion of Camera Channel from Screen Divided into 4 ...............................................２５ 2.7.4. Conversion of Camera Channel from Full Screen..
Linux DVR System 1. Setup Mode .........................................................................................................................５０ 2. Input of Admin’s Password ...............................................................................................５０ 2.1. Explanation of Admin’s Password Input Screen ............................................................ ５０ 2.2. Method of Password Input .....................................................................................
Linux DVR System 6. SETUP MODE-Color setup ................................................................................................７６ 6.1. SETUP MODE-Explanation of Color Setup Screen ...................................................... ７６ 6.2. Explanation of Color Setup Method............................................................................... ７７ 7. SETUP MODE – Motion Recording Setup........................................................................ ７８ 7.1. Motion Recording.....
Linux DVR System 11.3. Change of Setup in Sensor Menu............................................................................ １０３ 11.4. Setup of Recording Continuance Time .................................................................... １０４ 11.5. Setup of Recording (Camera) .................................................................................. １０５ 11.6. Alarm Setup.............................................................................................................. １０６ 11.7.
Linux DVR System I . Matters to be Noted Matters to be Noted Turn off the power of EliSS LD-1600 without fail before the installation. The persons other than professional installer should not open the cover of the case of this product at their own discretion. When verifying internal part of this product for system upgrade or repair of trouble, please ask to the place of purchase without fail. When installing this product, maintain approximately 15cm of distance from other nearby equipment.
Linux DVR System II . Composition of ELiSS LD-1600 Product Unpack the packaging of ELiSS LD-1600 and place ELiSS LD-1600 at the place to install. (Refer to installation safety information before the installation.) Check the contained material of the product before the installation.
Linux DVR System III . Major Features of ELiSS LD-1600 1. Accepted all merits of Window type DVR and Stand-Alone type DVR/removed demerits 1.1. Easiness of Operation Since the product is operated by button panel without using keyboard/mouse, the operating system is simple and intuitive, and anyone can easily operate. 1.2. Outstanding Stability As a Linux-based system, it could be bootable by flash memory instead of HDD, and the product is very stable.
Linux DVR System IV .
Linux DVR System Use of DHCP IP Network setup Net Mask Gateway Port Number of simultaneous users Network image quality (Select up to 1~5) ＊ SETUP N/O Setup Sensor N/C Storage continuous-time setup Storage Camera setup Alarm (Select up to ALARM 1~4) Alarm Setup N/O Continuous time N/C Parallel port setup Digital out System manager Screen divided into 16 Screen divided into 13 Screen divided into 9 ＊ DIV Screen divided into 8 Screen divided into 6 Screen divided into 4 Full screen PAN ＊ PT
Linux DVR System V . Name and Function of Each Part of ELiSS LD-1600 1. Name and Function of Each Part of Front Operating Panel Name of Operating Function Button ① USB Port ② 리모콘 센서 - Terminal for USB connection - 리모콘 신호를 수신하는 곳 입니다. ③ Camera Select (01~16) - When pressing the camera channel button desired among camera channel of 01~16 pieces, then the concerned screen is shown in full screen.
Linux DVR System 2. Name and Function of Each Part of Rear Side Connection Terminal VI . Name of Connection Terminal Function ① Power AC 100V ~ 240V, 50/60Hz ② CAM01~CAM12 Camera input terminal(12ch) ③ SENSOR INPUT Terminal receiving input of 16 sensors. ④ ALARM OUTPUT Terminal for the output of 4 alarms. ⑤ MOUSE Terminal for the connection of mouse. ⑥ keyboard Terminal for the connection of keyboard. ⑦ COM1 COM1 Port for the control of PTZ. ⑧ USB port Terminal for the connection of USB.
Linux DVR System VII . Method of Installing ELiSS LD-1600 1.
Linux DVR System VIII . Method of Use of ELiSS LD-1600 1. Power ON/OFF of ELiSS LD-1600 Power of DVR must be turned ON after all installation of ELiSS LD-1600 is completed. Check the voltage of input power before turning ON power switch. Using after converting power conversion switch on the rear side of ELiSS to the matching voltage. 1) Press power switch of ELiSS LD1600 long for approximately 4 seconds.
Linux DVR System 2. DISPLAY MODE(Monitor Mode) DISPLAY MODE(Monitor Mode) performs the function of showing the image in real time and moving image relayed through installed camera. When power of ELiSS LD-1600 turns ON, the user enters into Display Mode Screen. 2.1. Explanation of DISPLAY MODE Screen ③ ④ ⑤ ⑦ ② ① ⑧ ① As a DISPLAY sphere, present picture is the screen divided into 16. ( Refer to p. Change of screen division.) ② Indicates present MODE. Present MODE is DISPLAY MODE.
Linux DVR System 2.2. Explanation of Contents Displayed on Each Screen (The case when OSD setting is ON) SETUP-In general setup, when you change OSD setup to ON, setup value by each camera channel is displayed on the screen. The contents displayed on the screen are as follows. SETUP-When you change OSD setup to OFF in general setup, the following contents are not displayed on the screen. ( Refer to p.4.
Linux DVR System ③ Indication of Motion Sphere : When moving is sensed in the set area while in setup as motion storage, sensed area is changed to blue color. (Refer to Motion setup on p.68: 5.8..) ※ In camera setup, if Display of Motion Setup is set to OFF, no sphere indication is shown on the screen. 2.3. Conversion to Display Mode from Other Mode 2.3.1. Conversion to Display Mode from Search Mode If you press MODE button ( ) from Search Mode, conversion to DISPLAY MODE 로 is made. 2.3.2.
Linux DVR System 2.4. Change of Screen Dividing from Display Mode You can change screen dividing mode by using DIV button. Each one pressing of DIV button converts the screen in the order of 16-division screen → 13-division screen → 9division screen → 8-division screen → 6-division screen→ 4-division screen→ Full screen → 16-division screen → 13-division screen.…….
Linux DVR System 2.5. Automatic Channel Switching Function and TV OUT Automatic Channel Switching Function is the function that automatically change camera channel shown on the screen in case of screen divided into 13, screen divided into 9, screen divided into 8, screen divided into 6, screen divided into 4 and Full screen. When channel switching time interval is set up, camera channel on the screen automatically changes at the set time interval.
Linux DVR System 2.7.1. Conversion of Camera Channel from Screen Divided into 9 Firstly, set the division of the screen to the screen divided into 9 using DIV button. To convert camera channel which is shown on the screen, use ▲/▼button among Direction Movement buttons. ▲button increases (+) channel of the camera and ▼button decreases (-) channel of the camera. 2) ▲button increases (+) channel of the camera and ▼button decreases 1) Convert to screen divided into 9 by (-) channel of the camera.
Linux DVR System 2.7.2. Conversion of Camera Channel from Screen Divided into 8 Firstly, set division of the screen to the screen divided into 8 by using DIV button. To convert camera channel shown on the screen, use ▲/▼button among Direction Movement buttons in case of EliSS LD-1600. ▲button increases (+) channel of the camera and ▼button decreases (-) channel of the camera. .
Linux DVR System 2.7.3. Conversion of Camera Channel from Screen Divided into 4 Firstly, set division of the screen to the screen divided into 4 by using DIV button. To convert camera channel shown on the screen, use ▲/▼button among Direction Movement buttons in case of ELiSS LD-1600. ▲button increases (+) camera channel and ▼button decreases (-) camera channel.. 2) ▲button increases (+) 1) Convert into screen divided into 4 by camera channel and ▼button decreases (-) camera channel.
Linux DVR System 2.7.4. Conversion of Camera Channel from Full Screen Firstly, set division of the screen to Full screen by using DIV button. To change camera channel shown on the screen, use ▲/▼button among Direction Movement buttons in case of ELiSS LD-1600. ▲button increases (+) camera channel and ▼button decreases (-) camera channel. 2) ▲button increases (+) 1) Convert into Full screen by pressing DIV camera channel and ▼button decreases (-) camera channel. button.
Linux DVR System 2.8. Real Time Storage in DISPLAY MODE In ELiSS LD-1600, you can make real time storage in monitor mode. To do that, use ●REC button located on the front side of ELiSS LD-1600 in DISPLAY MODE screen. If you press ●REC button in Monitor Mode, it stores all the video displayed on the screen real time. Even if set up in schedule, it executes all the video. The stored date can be regenerated in the method of general search in Search Mode.
Linux DVR System 3. SEARCH MODE(RETRIEVAL MODE) Search Mode is a mode that can search/regenerate recorded image by date, by time. It is converted to Search Mode when pressing MODE button of front side of ELiSS from Display Mode. Search method has General Search and Event Search. 3.1. Explanation of Search Mode (RETRIEVAL MODE) Screen ⑤ ② ⑥ ⑦ ④ ③ ① Indicates Present Mode. Present Mode is Search Mode. ② Indicates date and time to search, and the user can personally select the date and time to search.
Linux DVR System 3.2. General Search General Search is a function that allows the user to select the time/date desired and search/regenerate entire stored data at such selected time. 3.2.1. Method of General Search ② ① ① Place cursor at general search button using ▲/▼ button among Direction Movement buttons located in the front side of ELiSS. When cursor is placed, general search button is lit with red light from blue light.
Linux DVR System 3.2.2. Regeneration of Generally Searched Data After selecting intended time/date, press ENTER button. Then conversion is made to the screen that regeneration of actual data can be done. 3.2.3. Explanation of Data Regeneration Screen ④ ⑥ ⑤ ① ② ③ ① Indicates present mode. Present mode is SEARCH MODE. ② Sphere where recorded data of searched time/date is regenerated. To change the division of screen, press DIV button located at front side of ELiSS.
Linux DVR System ⑥ Display present regenerating status of recorded data by icon. Displayed in red color according to reproducing status. ⓐ ⓑ ⓒ ⓓ ⓔ ⓐ If this icon is displayed in red color, it means that recorded data are being regenerated at right direction and right speed. ⓑ If this icon is displayed in red color, it means that regeneration of recorded data is discontinued. ⓒ When this icon is displayed in red color, it means that recorded data are regenerated at right direction and speed.
Linux DVR System 3.2.5. Change of Screen Division of Search Mode In order to change screen division, DIV button is used located on front side of ELiSS in same manner as Display Mode. Screen division is changed in the order of screen divided to 16 → screen divided to 9 → screen divided into 4 → Full screen →…screen divided into 16 →…for each 1 pressing of DIV button. DIV button을 눌러 화면분할 모드를 전환합니 다.
Linux DVR System 3.2.6. Conversion of Camera Channel from Search Mode This function is to watch camera channel which is not watched at present in 9-division screen/4-division screen/Full screen mode. In order to convert camera seen on the screen, use ▲/▼button among Direction Movement buttons in the same way as channel conversion. ▲button increases (+) camera channel and ▼button decreases (-) camera channel. (Refer to p.
Linux DVR System 3.2.7. Explanation of Regeneration Function Button This is to explain on regeneration function button located on the front side of ELiSS. ① Regenerates in the right direction at fast speed. ② Regenerates in the right direction at normal speed. Press once more to stop this temporarily. ③ Regenerates in the right direction at fast speed. ① ② ③ ④ If you press this during its being static, regeneration is made by one frame. ④ Converts this to Overlay Mode.
Linux DVR System 3.3. Event Search Motion storage is done when motion storage sphere is set and motion take place in such sphere. Event search allows the user to search by each camera channel for the stored data list through motion storage at intended time/date. 3.3.1. Explanation of Event Search Screen ⑥ ③ ④ ② ⑤ ① When event search is selected and entered into it, the above screen appears. ① Displays present mode. Present mode is Search Mode.
Linux DVR System 3.3.2. Method of Event Search ③ ② ④ ① ⑤ ① Position the cursor to event search using ▲/▼ button among Direction Movement buttons located on the front side of ELiSS between General Search and Event Search. When cursor is positioned, red light is lit on event search. ② After selecting Event Search, when you press ▶ button among Direction Movement buttons located on the front side of ELiSS, cursor appears in the camera channel selection window desired to search.
Linux DVR System ④ When selection is completed between MOTION/SENSOR, move the cursor to event search date setting window by pressing ▶ button located on the front side of ELiSS. In date setting window, ◀/▶button among Direction Movement buttons is used for the movement of cursor. ▲/▼ button among Direction Movement buttons is used for change of number. ⑤ When search time/date setting is completed, press ENTER button located on the front side of ELiSS.
Linux DVR System 3.4. SEARCH MODE-JPEG BACKUP JPEG Backup is a function to backup while search is made, and stores in picture file of JPEG format by each 1 frame. ① Connect USB hard disk to USB Port. ② Execute General Search or Event Search. (Refer to p.: 3.2. General search. P. 3.3. Event search). ③ Indicate the screen of the target camera as 1 channel mode by using camera number from No. 1 to 16 located on the front side of ELiSS LD-1600.
Linux DVR System IX . Backup of Stored Data By backing up stored data in USB Hard disk, users can watch the data at Windows environment of PC and ELiSS LD-1600. ※ JPEG Backup is possible in SEARCH MODE, and refer to P.38 : 3.4 SEARCH MODE-JPEG Backup. For backup of stored data, use BACKUP button located on the front side of ELiSS LD-1600. USB PORT When pressing BACKUP button from DISPLAY MODE and SEARCH MODE, it is converted to BACKUP MODE, and BACKUP MODE has two screens.
Linux DVR System 1. Explanation of Backup Initial-Screen ② ③ ⑤ ④ ① ① Indicates present mode. It is BACKUP MODE at present. ②, ③ Indicates time/date intended to search. User can set intended date of search at his own discretion. ④ This is calendar of the month intended to search. Data stored date is marked in red color, and the date data is not stored is marked in white color. ⑤ Storage is possible in two types.
Linux DVR System 2. Explanation of Backup Progress Screen ③ ⑥ ④ ② ⑤ ① ① Indicates present mode. Present mode is BACKUP MODE. ② This is a window showing data information inside ELiSS LD-1600 Hard disk. If stored data exist in ELiSS-1600 on set date from backup initial-screen, the data appear as one list. If quantity of list exceeds one screen, scroll bar appears in the right side of the window. Type of appeared data is “yyyy(year) mm(month) dd(date) hh(time)_01(camera No. of recorded image).ldv”.
Linux DVR System ⑤ This is a window indicating data information in USB hard disk. If you selected on the backup initial-screen, all data list of “idv” format appears, and if you selected ‘AVI Storage’, all data list of “avi” format appears. If quantity of list exceeds one screen, scroll bar appears in the right side of window. Type of shown data is “yyyymmddhh_01(camera No. of recorded image).avi”.
Linux DVR System 3. Explanation of Backup Method of Stored Data 3.1. Explanation of Backup Method with LDV Extension ① When pressing BACKUP button from DISPLAY MODE or SEARCH MODE screen, enters to BACKUP initial-screen. ② If you enter to BACKUP initial-screen for the first rime, there is cursor at the year of date selection screen. ③ The numbers can be changed using ▲/▼button among Direction Movement buttons. When pressing ▲button, numbers increase, and ▼button, numbers decrease.
Linux DVR System ⓑ ⓔ ⓒ ⓐ ⓓ ⓐ Select the data to backup to USB hard disk among data list inside ELiSS LD-1600 Hard disk. Selection of data is done by pressing ENTER button after moving cursor to data to backup. Use ▲/▼button among Direction Movement buttons for the move of cursor. Color of data which cursor is moved changes to red color, and when the data is selected, it changes to green color. When cursor is placed at selected data, it changes to violet color.
Linux DVR System 3.2. Explanation of Backup Method with AVI Extension Method of backup with avi extension is also same as the method of backup with ldv extension. However, button must be selected when selecting Storage Mode. ※ However, ldv backup can backup several files at same time, and avi backup can convert or backup a file of 1 hour into avi file after dividing it into 5 minutes unit. ① When BACKUP button is pressed from DISPLAY MODE or SEARCH MODE screen, the user enters BACKUP initial-screen.
Linux DVR System ⑤ The days marked in red color are the days when designated data exist, and the days marked in white color means the days when designated data do not exist. ⑥ When setup of date is completed, move the cursor to by pressing ▶button. When cursor is moved, red light is lit. When pressing ENTER button, BACKUP Proceeding screen which backup with avi extension is possible appears.
Linux DVR System button, and to delete selected data, press button. If you press button, it means that the user intends to select all data and backup. ⓒ When button is pressed after selecting one data list, the digits of 00 05 10…55 appear in central message window (ⓒ). 00 means the data in the duration of 0 ~ 5 minutes and 05 means the data in the duration of 5~10 minutes.
Linux DVR System 3.3. Method of Regeneration of Data in USB Hard disk in ELiSS DVR By moving the data in the USB hard-disk stored by ldv extension to the inside of hard-disk of ELiSS DVR., regeneration is possible in ELiSS LD-1600. When pressing BACKUP button from DISPLAY MODE or SEARCH MODE screen, you will enter to BACKUP initial-screen. The method of entering to Backup Progress screen is same as the explanation in ‘3.1 Method of Backup with ldv extension ’. ( Refer to p.41: 3.1.
Linux DVR System ◀ button among Direction Movement buttons. Press button to move selected data only into ELiSS LD-1600의 Hard-disk, and press to delete selected data. When button button is pressed, it means that you intend to select all data. The selection of button is known by change of button to red color when the cursor is positioned.
Linux DVR System X . Setup Method of ELiSS LD-1600 1. Setup Mode When SETUP button is pressed from DISPLAY MODE or SETUP MODE, conversion to SETUP MODE is done, and the Manager’s Password Input screen appears first. 2. Input of Admin’s Password 2.1. Explanation of Admin’s Password Input Screen 2003-11-19 pm 09:27 23 ③ ② ① ④ ① Indicates present mode. Present mode is SETUP MODE. ② This is password input window. ③ Indicates present time. ④ Indicates menus that can be set up in SETUP MODE.
Linux DVR System 2.2. Method of Password Input ① To input password, Camera Select button among the buttons located on the front side of ELiSS LD-1600 are used. No. 10 channel button is ‘0’ at the time of password input. ② For every 1 input of password by admin, 1 * mark is affixed on password input window. Indicating the password in * mark is for the security purpose. 2003-11-19 pm 09:27 23 **** ③ Password may be set in 4~8 characters, and initial password setting is ‘0000’.
Linux DVR System ⑤ When the password is correctly input, password input window disappears and converted to initial screen of Setup Mode. ⑥ If the password is incorrectly input, the message that the password is incorrect appears. ① If the password is incorrect, start input again from the beginning. 2.3. Conversion to Other Screen ① When the password is unknown, use CANCEL button on front side of ELiSS LD-1600 to convert to other screen.
Linux DVR System 3. Setup Mode Initial-Menu Screen 3.1. Explanation of Setup Mode-Initial Menu Screen ③ 2003-11-19 pm 09:27 23 ② ④ ③ ③ ① Indicates present mode. Present mode is Setup Mode. ② Indicates present time. ③ These are menus that can be set from Setup Mode. ④ Briefly explains the functions that can be set from selected menu. • When you select General Setup : Password, resetting of password, channel switching, rebooting, date setting.
Linux DVR System 3.2. Selection of Menu from Setup Mode ① The menus selectable from initial screen of SETUP MODE are general setup, storage schedule, network setting, sensor, alarm. ② The menu where cursor is located is lit with yellow light around its rim. The picture below is the shape which general setup is selected. ③ To change the position of cursor, use ◀/▶ button or ▲/▼ button located on front side of ELiSS LD-1600. When pressing ◀ button, cursor moves to the left.
Linux DVR System 4. Setup Mode – General Setup The menus that can be set from General Setup are password setting, channel switching, OSD, rebooting, date setting. 4.1. Setup Mode – Explanation of General Setup Screen ② ① 2003-11-19 pm 09:27 23 ④ ⑥ ③ ⑤ ① Displays present setup menu. Present menu is general setup menu. ② Displays present time. ③ Displays present mode. Present mode is Setup Mode. ④ These are menus that can be set up from general setup. A. Shows presently set values.
Linux DVR System 4.2. Setup Mode – Selection of General Setup Menu 2003-11-19 ① ① ② pm 09:27 23 ② ① When you enter selecting general setup from entire menu selection screen of SETUP MODE, the first cursor is positioned in the password among general setup menu. The menu in which cursor is located partially shines with yellow light in the front side.
Linux DVR System 4.3. Changing Password This is the menu for the change of password of manager. Basic setup is ‘0000’. ① Cursor is moved with password among general setup menu. Move cursor using ▲ /▼button among Direction Movement buttons. Concerned menu shines with yellow light. ② When pressing ▶button among move buttons, the cursor appears in the first column as yellow light is lit around the rim of the setup window that shows present setup value in the right side of concerned menu.
Linux DVR System 4.4. Channel Switching Setup and TV OUT Channel switching function is the function that automatically converts camera channel seen on the screen when the screen is 13-division screen, 9-division screen, 8division screen, 6-division screen, 4-division screen and full screen. If time interval of channel switching is set up, camera channel of screen is automatically converted at set time interval. If not intended to set channel switching, set the value to 0 second.
Linux DVR System 4.5. OSD Setup OSD sets whether or not to display the information such as camera ID and sensor, Pantilt camera setting, storage status, etc. on displaying screen. ① Move cursor to OSD among general setup menu. Use ▲/▼button for the move of cursor. When OSD menu is selected, yellow light is lit. ② When pressing ▶button among move buttons, yellow light is lit around the rim of setup window that show present setup value at the right side of concerned menu, and ON/OFF is selectable.
Linux DVR System 4.6. Setup of Rebooting This is a menu for regular rebooting of the system. If you don’t want to do rebooting, set the value to 0 second. Basic setup is set as 0 hours 60 days. ① Move the cursor to rebooting among general setup menu. Use ▲/▼button for the move of cursor. When rebooting menu is selected, yellow light is lit.
Linux DVR System 4.7. Date Setup Date Setup is a menu to set correct time when the date of time of system is incorrect. When time is newly set, all of the stored data are deleted. Basic setup is current time of the system. ① When cursor is moved to date setup among general setup menu, yellow light is lit to the date setup. For the move of cursor, ▲/▼button among Direction Movement buttons is used. ▲button moves the position of cursor upward. ▼ button moves the position of cursor downward.
Linux DVR System 4.8. Movement to Initial Menu Screen of Setup Mode from General Setup Screen In order to move again to initial menu screen of Setup Mode from general setup screen, conversion is made by pressing ENTER button or CANCEL button located on the front side of ELiSS LD-1600 from the top stage of general setup, ① This means that ENTER button on the front side of ELiSSLD-1600 converts to Setup Mode initial-menu screen after storing newly set value.
Linux DVR System 5. Setup Mode – Camera Setup The menus that can be set in camera setup are camera ID, Frame rate, Video type, PTZtype / camera ID, storage status, Motion sensitivity setup, Motion continuous time, compressed picture quality, alarm, resolution. 5.1. Setup Mode – Explanation of Camera Setup Screen ③ ② ④ ⑥ ⑤ ① ① Indicates present mode. Present mode is Setup Mode. ② Displays present time. ③ Presently set menu. This is camera setup menu at present.
Linux DVR System 5.2. Setup Mode – Designation of Camera from Camera Setup Initial-Screen ① When camera setup menu is selected from initial menu screen of Setup Mode, first cursor is positioned at No. 1 camera (CAM01). Yellow light is lit on the camera where the cursor is positioned. ② When intended to designate other camera, ▲/▼button among Direction Movement buttons is used. ▲button moves the cursor upward. ▼button moves the cursor downward.
Linux DVR System 5.3. Changing Camera ID User can change ID of camera at user’s own discretion to enable easy classification of camera. Basic setup is set for ‘CAM+Camera No. ① Move cursor with ID among camera setup menu. ▲/▼button among Direction Movement buttons is used for the move of camera. ▲button moves cursor with upper menu and ▼button moves cursor with lower menu.
Linux DVR System 5.4. Setup of Frame Rate This is a menu to set up the number of frame stored in each 1 second. A maximum up to 15frame can be set up. Basic setup is set for 10fps. ① Move cursor with Frame rate among Camera Setup Menu. ▲/▼button among Direction Movement buttons is used for the move of cursor. ▲button moves cursor upper menu and ▼button moves cursor to lower menu.
Linux DVR System 5.5. Setup of Video type This is a menu for the setup of the type of analog signal entering through camera. At present, only NTSC is supported. ① Move cursor with Video type among Camera Setup menu. ▲/▼button among Direction Movement buttons is used for the move of cursor. ▲button moves cursor to upper menu. ▼button moves cursor to lower menu. ② When pressing ▶button among Direction Movement buttons, yellow light is lit around the rim of setup window which shows present setup value.
Linux DVR System 5.6. Setup of PTZ Type / ID This is a menu to setup type and ID of Pantilt camera among the camera. Basic setup is set to ‘NO PANTILT’, and ‘00’ is set for ID as the basic setup. ① Move cursor with PTZ Type / ID among Camera Setup Menu. For the move of cursor, use ▲/▼button among Direction Movement buttons. ▲button moves cursor to upper menu and ▼button moves cursor to lower menu.
Linux DVR System 5.7. Setup of the Status of Recording Status of recording can be set up by each camera. There are ‘Recording’, ‘No Recording’, ‘Schedule’ in the status of recording. ‘Recording’ means intending entire recording, ‘No Recording means not to store. ‘Schedule’ means to store as the schedule set up in recording schedule of Setup Mode. Basic setup is set as ‘Recording’. ① Move cursor with Storage Status among Camera Setup Menu.
Linux DVR System 5.8. Setup of Motion Set the storage status of camera setup to ‘Schedule’, and execute Motion Storage in case when motion storage was set from Setup Mode – Schedule. Motion sensitivity setup is the menu for the setup of degree of reaction when there is any motion in setup sphere. (Refer to Schedule in p.84: 9. SETUP MODE-Schedule.) Its value can be set from 1 to 10 depending on the sensitivity, and 10 is most sensitive. Basic setting is set to 6. 5.8.1.
Linux DVR System 5.8.2. Setup of Motion Continuance Time This is a menu to setup recording time when moving is caught in Setup sphere in case when Motion Storage is set at Storage Schedule of SETUP MODE. Basic setting is set to 3 seconds. ① Move cursor by pressing ▶button, and change continuous time using ▲/▼button among Direction Movement buttons. The number increases when ▲button is pressed and decreases when ▼button is pressed.
Linux DVR System 5.9. Setup of Compressed Image Quality This is a menu for the setting of image quality of data being stored. Setting can be done from 1 to 5, and 5 is the best image quality. File size is in proportion to the image quality. When the image quality is set low, file size also becomes smaller, and the file size becomes bigger when image quality is set high. Basic setting is set to 4. ① Move Cursor to compressed display among camera setup.
Linux DVR System 5.10. Setup of Alarm This is a menu to ring Alarm when movement in set sphere is sensed at Storage Schedule of SETUP MODE. User can select one among 4 alarms. Basic setting is set to OFF. (Refer to p.104: 12. SETUP MODE-Alarm Setup.) ① Move cursor to Alarm among Camera Setup Menu. ▲/▼button among Direction Movement buttons is used for the move of cursor. ▲button moves the cursor to upper menu and ▼button moves the cursor to lower menu.
Linux DVR System 5.11. Setup of Resolution Resolution by each camera channel can be changed at the discretion of the user. Since the resolution influences storage capacity, resolution may be set differently depending on the importance of each camera channel. Basic setting is 320x240. ① Move cursor to Resolution among camera setup menu. ▲/▼button among Direction Movement buttons is used for the move of cursor. ▲button moves cursor to the upper menu and ▼button moves cursor to the lower menu.
Linux DVR System 5.12. Movement to Initial Menu Screen of Setup Mode from Camera Setup Screen To move again to Initial Menu screen of Setup Mode from Camera Setup screen, conversion is made by pressing ENTER button or CANCEL button after going to the designated screen of the camera by pressing ENTER button. ① ENTER button means converting to Initial Menu screen of Setup Mode after storing newly set value.
Linux DVR System 6. SETUP MODE-Color setup User can select color the value of Capture screen and the value of Overlay screen, respectively. The menus that can be set up from Color Setup are BRIGHTNESS, CONTRAST, SATURATION, HUE. 6.1. SETUP MODE-Explanation of Color Setup Screen ③ ④ ⑤ ② ⑥ ① ① Displays present MODE. Present MODE is COLOR SETUP MODE. ② Displays the screen to set color value in full screen, and the user can confirm the change of color value. ③ Displays present time.
Linux DVR System 6.2. Explanation of Color Setup Method User can set each respective value of BRIGHTNESS / CONTRAST / SATURATION / HUE of Capture screen and Overlay screen. ① After moving cursor to MENU, Capture and Overlay can be selected using ◀/▶button among Direction Movement buttons. Selected value is lit with yellow light. ② After selecting Capture and Overlay, select menu to change the setting among BRIGHTNESS/CINTRAST/SATURATION/ HUE using ▼/▲button among Direction Movement buttons.
Linux DVR System 7. SETUP MODE – Motion Recording Setup 7.1. Motion Recording Motion Storage starts the storage when the movement is sensed in the sphere after designating a sphere on the screen. User can know the execution of motion storage of concerned camera by the display of motion storage initial (M) on the screen. 7.1.1.
Linux DVR System ④ If cursor moves to Storage status, yellow light is lit on ‘Storage Status’. ⑤ When pressing ▶button among Direction Movement buttons, yellow light is lit on the rid of setup window that shows present setup value of concerned menu. ⑥ Set the storage status of concerned camera to ‘Schedule’ using ▲/▼button among Direction Movement buttons. Change is made in the order of Storage→ Schedule→ No storage on every pressing of ▼button.
Linux DVR System ⑩ When Motion Continuance Time is completed, press ENTER button. Then, yellow light on the rim of setup window is turned off and cursor in setup window also disappears. ⑪ If the user does not use Overlay board in ELiSS LD-1600, the user can set up Motion sphere DISPLAY ON/OFF. To set up Motion sphere DISPLAY ON/OF, move cursor to Display by pressing ▶button among Direction Movement buttons. The user can change ON/OFF using ▲/▼button among Direction Movement buttons.
Linux DVR System 8. SETUP MODE – Motion Recording Sphere Setup If the time of Motion Storage is set from Storage Schedule of SETUP MODE, storage is executed when the movement on the set time was detected by concerned camera. If you select Motion Sphere Setup Menu from initial screen of Setup Menu Selection, you enter to Motion Sphere Setup screen. 8.1. Explanation of Motion Sphere Setup Screen ELiSS LD-1600 can setup motion sensing sphere by each camera channel.
Linux DVR System 8.2. Setup Method of Motion Sensing Sphere ① Select camera to setup Motion Sensing Sphere. When first ① entering into Motion Sensing Sphere Setup screen, cursor is placed in CAM01. Use ▲/▼button among Direction Movement buttons for the move of cursor. When cursor is placed, yellow light is lit. When pressing ▶button among Direction Movement buttons after placing cursor at intended camera, cursor moves to Motion Sphere Setup Menu.
Linux DVR System ③ Designate as Motion Sensing Sphere at the part not set up as Motion Sensing Sphere by pressing ENTER button. If designated as Motion Sensing Sphere, such part is seen as green color at the beginning, and seen as blue color when cursor moves. Movement of cursor ④ Setup is cancelled when pressing ENTER button at the part set up as Motion Sensing Sphere.
Linux DVR System ⑤ At upper side and left side of the screen where Motion Sensing Sphere is set up, image bar is located which was divided into 8 each column. If you press ENTER button with cursor placing on this image bar, setting of one lower line (or right side line) of the relevant column is changed.
Linux DVR System ⅲ) Setup of entire screen Press ENTER button placing the position of cursor on the intersection column of horizontal line and vertical line of image bar. Motion Sphere Setup is cancelled when ENTER button is pressed once more. ⑥ Entire Setup of Motion Sensing Sphere is cancelled when CANCEL button is pressed. ⑦ When the Setup of Motion Sensing Sphere is completed, move the cursor inside the screen to outside the screen.
Linux DVR System ② CANCEL button means converting to initial menu screen of Setup Mode maintaining existing value without storing newly set value. When the user presses CANCEL button from the top stage even if the user pressed ENTER button from the lower stage, the new value set by the user is not stored and the existing value is maintained.
Linux DVR System 9. SETUP MODE – Schedule Schedule sets up the schedule stored at the time when storage status is set to schedule at Camera Setup by each camera. The menus that can be set up at Storage Schedule are Storage Schedule Setup and Schedule Application Scope Setup. 9.1. SETUP MODE – Explanation of Schedule Screen ③ ⑤② ⑥ ④ ① ① Indicates present MODE. Present MODE is SETUP MODE. ② Menu being set up presently. This is Storage Schedule Menu now. ③ Indicates present time.
Linux DVR System 9.2. SETUP MODE – Designation of Camera at Schedule Setup Screen ① If you select and enter the initial screen of Storage Schedule from initial screen of Setup Mode, cursor is placed in No. 1 camera (CAM 01). The camera in which cursor is placed shines with yellow light. ② To setup other camera, use ▲/▼button among Direction Movement buttons.
Linux DVR System 9.3. Method of Schedule Setup When storage time is set up at storage menu of storage schedule and set the storage status to ‘Schedule’, concerned camera does entire storage according to set schedule. The user can identify the execution of entire storage by concerned camera by the display of entire storage initial (R) on the screen. These setup values can be changed at the user’s own discretion.
Linux DVR System ⅱ) Change of schedule setup of vertical line (time) When ENTER button is pressed after setting intended cursor to Time, change of concerned time setting of the weekday is possible at the same time. For every pressing of ENTER button, setup is changed in the order of ‘Entire storage→Motion storage→ No storage.
Linux DVR System ④ When all setting is completed, move the cursor to the left side and exit from the window using ◀ button among Direction Movement buttons. 9.4. Setup of Application Scope of Schedule ① When pressing ▼button among Direction Movement buttons once more, scope of schedule can be set up.
Linux DVR System 10. SETUP MODE – Network Setup ELiSS LD-1600 provides real-time remote monitor function through network. Real-time image transmission from remote place, search and backup of recorded data, multichannel interface, ‘multi-to multi’ interface are possible. In network setup, method of interface and setup of low order menu incidental thereto is possible. For the method of interface, LAN, ADSL, PSTN/ISDN method is possible. Currently possible method is LAN.
Linux DVR System 10.2. Setup of DHCP (Method of IP Address Setup) When DHCP is used, the system, not the user, automatically setup IP, Net Mask, Gateway, etc. If DHCP is not used, the user can personally setup IP, Net Mask, Gateway, etc. Method of interface is set for LAN method. Protocol : Like the language used by human, such language exist in computer communication. Protocol is a promise of language for the communication among computers..
Linux DVR System 10.3. Change of IP Setup Value This is the menu to personally setup IP of ELiSS LD-1600 when ‘DHCP Setup’ is set for ‘Not use’. Basic setup is set to 192.168.000.098. ① When cursor is moved to IP among network setup menu, yellow light is lit. For move of cursor, ▲/▼button among Direction Movement buttons on the front side of ELiSS is used..
Linux DVR System 10.4. Change of Net Mask Setup Value This is the menu to set up Net Mask of ELiSS LD-1600 when ‘DHCP setup’ is set to ‘Not use’. Basic setup is set to 255.255.255.000. ① When cursor is moved to Net Mask among network setup menu, yellow light is lit. ▲/▼button among Direction Movement buttons is used for the move of cursor.
Linux DVR System 10.5. Change of Gateway Setup Value This is the menu to setup Gsteway of ELiSS LD-1600 when ‘DHCP Setup’ is set to ‘Not use’. Basic setup is set to 192.168.000.254. ① When cursor is moved to Gateway among network setup menu, yellow light is lit. ▲/▼button among Direction Movement buttons is used for the move of cursor.
Linux DVR System 10.6. Change of Port Setup Value This is the menu to setup Port No. of ELiSS LD-1600 when ‘DHCP’ is set to ‘Not use’. Basic setup is set to 05005. ① When cursor is moved to Port among network setup menu, yellow light is lit. ▲/ ▼button among Direction Movement buttons is used for the move of cursor.
Linux DVR System 10.7. Change of Setup Value of the Number of Simultaneous Users This is the menu to set the number of users who can interface simultaneously with ELiSS LD-1600 in EyeLinker (remote place). Basic setting is set to 06 persons. ① When cursor is moved to the ‘number of simultaneous users’ among network setup menu, yellow light is lit. ▲/▼button among Direction Movement buttons is used for the move of cursor.
Linux DVR System 10.8. Change of Setup Value of Network Image quality This is the menu for user’s selection of image quality of the screen transmitted by EyeLinker (Remote place). Basic setting is set to 01. ③ When cursor is moved to the ‘Network image quality’ among network setup menu, yellow light is lit. ▲/▼button among Direction Movement buttons is used for the move of cursor.
Linux DVR System 10.9. Movement to Menu Selection Initial-Screen of Setup Mode from Network Setup Screen To return to initial menu screen of Setup Mode after completing all setup on Network Setup Screen, press ENTER button or CANCEL button. ① ENTER button means to convert to Setup Mode initial menu screen after storing newly set value ② CANCEL button means to convert to Setup Mode initial menu screen maintaining existing value without storing newly set value.
Linux DVR System 11. SETUP MODE – Sensor Setup At Sensor Setup Menu, setup, continuance time, storage and alarm are set up. 11.1. SETUP MODE-Sensor Setup Screen ③ ② ⑤ ⑥ ④ ① ① Indicates present MODE. Present Mode is SETUP MODE. ② The menu being set presently. Indicates sensor menu at present. ③ Indicates present time. ④ Select the sensor intended to set up among 16 sensors. ⑤ This is the menu which can be set up from sensor menu. ⑥ This is a setup window indicating duly set value at present.
Linux DVR System 11.2. Method of Designation of Sensor Intended to Set up ① When entering to sensor setup screen after selecting sensor at initial menu selection screen of SETUP MODE, first cursor is located at No. 1 (SEN 01) sensor among the sensors.. The sensor in which cursor is located is lit with yellow light. ② Designate wanted sensor by moving cursor. Use ▲/▼button among Direction Movement buttons for the move of sensor.
Linux DVR System 11.3. Change of Setup in Sensor Menu This is the menu to select the kind of sensor. Selection is possible between N/C (Normally Close) and N/O (Normally Open). Basic setup is set for N/O (normally Open). ④ Move cursor to Setup among Sensor Menus. ◀/▶button among Direction Movement buttons is used for the move of cursor. ◀button moves cursor to left side direction and ▶button moves the cursor to right side direction.
Linux DVR System 11.4. Setup of Recording Continuance Time When event happened to the sensor, the time to store the screen of camera must be set. Basic setting is 3 seconds. ① Move the cursor to storage continuance time among sensor menu. ▲/▼button among Direction Movement buttons is used for the move of cursor. ▲button moves cursor to upper side and ▼button moves cursor to lower side. Yellow light is lit on the position where cursor is located.
Linux DVR System 11.5. Setup of Recording (Camera) This is the menu to set up camera which assume storage when the event happened to concerned sensor. Basic setting coincides between the sensor No. and the No. of camera to assume storage. ① Move the cursor to storage time among sensor menu. ▲/▼button is used for tthe movement of cursor. ▲button moves cursor to upper side and ▼button moves cursor to lower side. Yellow light is lit on the position where cursor is located.
Linux DVR System 11.6. Alarm Setup This is the menu to set up the alarm which reacts when event happened to concerned sensor. Basic setting is ALARM01. ALARM has 01~ 04. ① Move the cursor to alarm time among sensor menu. ▲/▼button is used for the move of cursor. ▲button moves cursor to upper side and ▼button moves cursor to lower side. Yellow light is lit on the position where cursor is located.
Linux DVR System ② CANCEL button means converting to initial menu screen of Setup Mode maintaining existing value without storing newly set value When the user presses CANCEL button from the top stage even if the user ENTER button from the lower stage, the new value set by the user is not stored and the existing value is maintained.
Linux DVR System 12. SETUP MODE – Alarm Setup SETUP MODE – The functions selectable from alarm mode are selection and continuance time. 12.1. Explanation of Alarm Setup Screen ② ③ ⑤ ⑥ ④ ① ① Indicates present mode. Present MODE is SETUP MODE. ② The menu that can be set up at present. Present menu is Alarm. ③ Indicates present time. ④ Designates the alarm intended to set. ⑤ The menu that can be set from alarm menu. ⑥ Indicates presently set value.
Linux DVR System 12.2. Designation of Alarm to be Set up ① When entering to alarm setup screen from initial menu screen of SETUP MODE, cursor is located at No. 1 Alarm (ALARM 01) among Alarm Designation Menu. Yellow light is lit on the alarm on which the cursor is located. ② Designate the alarm by moving cursor. Use ▲/▼button among Direction Movement buttons for the move of cursor. ▲button moves cursor to upper direction and ▼button moves cursor to lower direction.
Linux DVR System 12.3. Change of Setup in Alarm Menu This is the menu to select the kind of alarm. Selection is possible between N/C (Normally Close), N/O (Normally Open). Basic setting is set to N/O(Normally Open). ① After designating the alarm to change the setting, move cursor to Setup among Alarm Menus. Use ◀/▶button among Direction Movement buttons for the move of cursor. ◀button moves cursor to left direction and ▶button moves cursor to right direction.
Linux DVR System 12.4. Setup of Alarm Continuance Time This is the menu to set up the time of ringing of alarm. Basic setting is set to 3 seconds. ① Move cursor to continuance time among Alarm Menu. Use ▲/▼button among Direction Movement buttons for the move of cursor. ▲button moves cursor upward and ▼button moves cursor downward. Yellow light is lit on the menu where cursor is located. 0.
Linux DVR System ① ENTER button means converting to initial menu screen of Setup Mode after storing newly set value. ② CANCEL button means to convert to initial menu screen of Setup Mode maintaining existing value without storing newly set value. When the user presses CANCEL button from the top stage even if the user ENTER button from the lower stage, the new value set by the user is not stored and the existing value is maintained.
Linux DVR System 13. SETUP MODE – Parallel Port Setup SETUP MODE-Setup of parallel port enables the control of input/output device from remote place. For example, opening/closing of camera monitored entrance/exit door is controlled by parallel port or turning on or off of fluorescent lights are possible. Maximum of 8 devices that can control input/output with Parallel port can be set up. 13.1. Explanation of Parallel Port Setup Screen ② ③ ④ ⑤ ① ① Indicates present MODE. Present MODE is SETUP MODE.
Linux DVR System 13.2. Method of Parallel Port Setup Enter to parallel port setup screen selecting parallel port setup from initial screen of SETUP MODE. ※ Check if the cable is well connected to parallel port of ELiSS LD-1600 before the setup of parallel port. ① Move cursor to parallel port desired to set up among 8 parallel ports. ▲ / ▼ button among Direction Movement buttons is used for the move of cursor. Yellow light is lit in the menu where cursor is located.
Linux DVR System 14. PTZ CONTROL MODE When pressing VIEWERSET button located at front side of ELiSS LD-1600 in DISPLAY MODE, conversion to PTZ CONTROL MODE is done. In PTZ CONTROL MODE, control of PTZ camera (PAN/TILT, ZOOM, FOCUS, LIGHT, POWER) is possible. 14.1. Explanation of PTZ Control Mode Screen ③ ④ ① ② ① Indicates present MODE. Present MODE is PTZ CONTROL MODE. ② This is the sphere displayed in full screen. ③ Indicates present time. ④ The menu selectable from PTZ CONTROL MODE.
Linux DVR System 14.2. Selection of PTZ Control Mode Menu When selecting the menu of PTZ CONTROL MODE, ▲/▼ button among Direction Movement buttons located at front side of ELiSS LD-1600 is used for the move of cursor. The menu on which cursor is located is lit with yellow light. ENTER button is used for the selection of menu on which cursor is located. And you can convert the channel into the channel intended to operate PTZ camera by using Camera Select button located on the front side of ELiSS LD-1600.
Linux DVR System 14.3. PTZ Camera Control Method To control PTZ camera, PTZ camera must firstly be set up from SETUP MODE camera setup. If you set PTZ camera and set OSD to ON in General Setup, Pan Tilt initial (P) is shown on the left side of concerned screen at DISPLAY MODE. Control of PTZ camera at PTZ CONTROL MODE is possible only when PTZ camera is actually connected and concerned protocol is set up. 14.3.1.
Linux DVR System 14.3.3. Control of FOCUS ① When ‘FOCUS’ menu is selected, yellow light is lit, and other menus are displayed in black color. ② When using ▲/▼ button among Direction Movement buttons located on the front side of ELiSS LD-1600, FOCUS can be controlled. ③ When pressing ENTER button once again, other menu can be selected again. 14.3.4. Control of LIGHT ① When ‘LIGHT’ menu is selected, yellow light is lit, and other menus are displayed in black color.
Linux DVR System 14.3.5. Control of Power ① When ‘POWER’ menu is selected, yellow light is lit, and other menus are displayed in black color. ② When ▲/▼button among Direction Movement buttons located on the front side of ELiSS LD1600 is used, the POWER of PTZ camera can be turned on and off. ③ When pressing ENTER button once again, other menu can be selected again.
Linux DVR System X . Product Specifications For ELiSS LD-1600 Model name Spec. H/W spec ELiSS LD-1600LX CPU Pentium-Ⅳ 2.
Linux DVR System XI . Troubleshooting Guide To shorten the time of problem solution, the user is requested to verify following problem solution method in advance before judging as trouble. Problem No storage. [Store icon ( Answer 1 Verify if video type is set to NTSC at camera setup. Answer 2 Answer 3 Problem Answer 1 Verify if camera store is set to ‘store’. Isn’t it set to ‘No storage’ or ‘Schedule’? Adjust storage time of store schedule of SETUP MODE if store status is set to Schedule.
Linux DVR System Problem Answer 1 In VIEWER SET MODE, PAN/TILT, ZOOM/FOCUS of Pantilt camera is not adjusted. Verify if camera setup is set to PTZ camera. Verification can be done by existence of PTZ camera initial ( P ). If PAN/TILT, ZOOM/FOCUS is not adjusted while PTZ camera initial ( P ) Answer 2 is displayed on the screen, check PTZ Type and ID are set in correct manner. Problem Answer 1 ZOOM IN/OUT, PAN/TILT of PAN/TILT camera is not adjusted in PANTILT CONTROL MODE of ELiSS CENTER.
Linux DVR System XI . Quality Warranty This product is manufactured through thorough Quality Control and strict Inspection Process. In case when this product is used in compliance with the instructions of User’s Manual in ordinary environment for 1 year, Product Quality Warranty Term, free repair service is provided in accordance with this Letter of Quality Warranty. Restriction to Cost-Free Warranty Even during 1 year of free warranty term, charged service will be provided in the following cases.
Linux DVR System Users are requested to fill in and keep the contents in the Quality Warranty Letter for A/S. Quality Warranty Letter Product name Product No. Warranty term Date of purchase 1 year from the date of sale Year Month day Company name User Name Address Phone No. Company name Seller Name Address Phone No.
