User Manual

ManualsBrandseLine Technology ManualsCamcordersPRO3 Effio E

Instruction

Guide

Features

Professional

CCTV

Camera

The lightning with an arrowhead symbol, within an equilateral triangle

is intended to alert the users to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be

sufcient magnitude to constitute a risk of electric shock to persons.

The exclamation point with an equilateral triangle is intended to alert

the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

This equipment has been tested and found to comply with limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy, if not

installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the

interference at his own expense.

Changes or modications not expressly approved by the manufacturer

could void the user’s authority to operate the equipment.

To prevent electric shock and risk of re hazards:

• Do NOT use power sources other than that specied.

This installation should be made by a qualied

service person and should conform to all local codes.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NO REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

P/N 01.BSM.12.0086101A Printed on recycled paper

Efo-E Range

OSD Menu

Effio-E Enhanced

Privacy Masking

Motion Detection

Advance BLC

Anti-Colour Rolling

Front IR Compensation

Revision v1.1

Models:

Box Camera PAGE 1-4

Vandal Dome PAGE 5-8

Internal Dome PAGE 9-12

IR Bullets PAGE 13-18

IR Vandal PAGE 19-20

OSD Guide PAGE 21+

Summary of content (18 pages)

PAGE 1
CAUTION Instruction Guide Professional RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NO REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning with an arrowhead symbol, within an equilateral triangle is intended to alert the users to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude to constitute a risk of electric shock to persons.
PAGE 2
Identification Installation Mechanical Drawing 133 mm 5 in Installation information (General overview) 71 mm 3 in +~ ~- AC24V/DC12V 64 mm 2 1/2 in VIDEO I/O 121 62 +~ 1 ~- 24VAC / 12VDC L I/O 3 60 IRIS VIDEO 2 2 4 5 7 (b) Adapter-ring 4 3 Figure: Auto iris connector Jack Video iris lens 3 6 DC iris lens 1 Power Damp- 2 Null Damp+ 3 Video signal Drive+ 4 Ground Drive- 1) Black RS-485+ (Effio-P & Effio-S) 2) Brown RS-485- (Effio-P & Effio-S) 3) Orange NC 4) Blue
PAGE 3
Identification Installation Mechanical Drawing Installation information (General overview) 145 mm 5 3/4" 74 mm 3" +~ 1 ~- 64 mm 2 1/2" 24VAC / 12VDC VIDEO OUT I/O 145 mm 5 3/4" 1 74 mm 3" 3 + - AC24V/DC12V 63 mm 2 1/2" 2 2 3 LED 4 1 Accessories I/O Connector VIDEO 1 2 4 5 7 (a) Auto Iris connector Rear I / O Interface.
PAGE 4
Identification Installation 4.4" (112 mm) Mechanical Drawing Installation information (General overview) Ø 98.0 mm 4 in 1 3/4’’ -14 NPS thread 5.1" (130 mm) 2 Base Fitting Underside 46.0 mm 2 in 3 4 5 6 83.5 mm 3 1/2 in 4S Mounting Plate 4S Junction Box Fitting Accessories (A) Wall Plugs S8 x 30mm 4pc (B) Fitting Screws PA4 x 35mm 4pc NOTE: Make sure you don’t have any missing parts before you make the installation.
PAGE 5
Identification Installation Mechanical Drawing Installation information (General overview) 3/4” - 14 NTS thread Close / Open 127 mm 5 in 3/4” 14 NTS thread 83.5 mm 3 1/2 in 1 2 3 4 46.0 mm 2 in 150 mm 6 in Accessories 5 (A) Wall Plugs 5.6 x 29mm (C) Opening Tool 50 x 1.8mm (B) Fitting Screws PA4 x 30mm (D) L-Wrench T15 Size NOTE: Make sure you don’t have any missing parts before you make the installation.
PAGE 6
Identification Installation Mechanical Drawing Installation information (General overview) 100° 112 mm 4.4 in 137° 123° 1 2 5.1" 130 mm Indoor Dome Dimensions 27 mm 1.1 in Underside Base hole positions 39 mm 1.5 in Accessories Recess Mount Fitting dimensions (A) Wall Plugs S8 x 30mm 4pc 115 mm 4.5 in 4 5 6 7 mm .28 in Recess cutout and fitting clearance. (B) Fitting Screws PA4 x 35mm 4pc NOTE: Make sure you don’t have any missing parts before you make the installation.
PAGE 7
Identification Mechanical Drawing Installation Ø 150 mm 6 in Installation information (General overview) Ceiling Dome base 109 mm 4 1/2 in Cut Away for Cable side exit 1 150 mm 6 in 2 Side cable exit Location Dome cover (transparent) Lens (Vari-focal models) Power & Video Cable hole Body Cover 3 Dome base Standard Model Mounting Holes BOTTOM View 4 IR LED Model Dome Cover Release Clip Video 비디오connector 커넥터 Zoom adjustment 5 Focus adjustment Rotate 180° Pan360° Tilt 90° Standard Model
PAGE 8
Identification Installation Mechanical Drawing Installation information (General overview) 311 mm 12 in 99 mm 4" 1 292 mm 11 1/2" 2 69 mm 2 1/2" Pan Left - Right adjustment 294 mm 11 1/2" 3 99 mm 4" 4 View Tilt Angle adjustment 282 mm 11" 69 mm 2 1/2" 5 Accessories (A) Wall Plugs S8 x 30mm 4pcs (B) Fitting Screws PA4 x 35mm 4pcs (E) Optional Junction Box (C) Sunshield Screw M3 x5mm (D) L-Hex tool 47x17mm (F ) Drill Hole template (Junction box holes also) NOTE: Make sure you don’t hav
PAGE 9
Identification Installation Mechanical Drawing Installation information (General overview) 100 mm 4" 185 mm 7 1/2" 185 mm 7 1/2" 1 2 Focus adjustment 298 mm 11 1/2" Video 비디오connector 커넥터 3 Accessories Power connector Type B 전원 커넥터 4 Type A View Angle adjustment (A) Wall Plugs S8 x 30mm 4pcs (B) Fitting Screws PA4 x 35mm 4pcs (C) Sunshield Screw M5 Thread (D) Allen Key 47x17mm NOTE: Make sure you don’t have any missing parts before you make the installation.
PAGE 10
Identification Installation Mechanical Drawing Installation information (General overview) 190 mm 7 1/2" 61.5 mm 2 1/2" 75 mm 3" 2 1 Video 비디오connector 커넥터 75 mm 3" Power connector Type B 전원 커넥터 3 Ø 62 mm 2 1/2" Accessories (B) Fitting Screws PA4 x 35mm 4pcs (C) Sunshield Screw M3 x5mm NOTE: Make sure you don’t have any missing parts before you make the installation. Incorrect installation could void the warranty if instructions are not followed correctly.
PAGE 11
Identification Installation Mechanical Drawing Installation information (General overview) 70 70 mm 3" 120 70 120mm 41/2" 70 mm 3" 105.5mm 4" 1 2 Video 비디오connector 커넥터 Power connector Type B 전원 커넥터 Ø 120 mm 4 1/2" 3 Accessories (A) Wall Plugs S8 x 30mm 4pc (B) Fitting Screws PA4 x 35mm 4pc (C) Adjustment Tool Vari-Focal Model NOTE: Make sure you don’t have any missing parts before you make the installation.
PAGE 12
CAMERA ADJUSTMENT CAMERA ADJUSTMENT OSD MENU control RCA Service Connector Use supplied RCA - BNC cable If you require BNC output. Press down on the function joystick to access the setup menu. • Main setup menu is displayed on the monitor screen. OSD function joystick. Pressing down on joystick acts as ENTER function. SETUP MENU The OSD control may differ from show above, OSD buttons may replace the joystick type.
PAGE 13
CAMERA ADJUSTMENT LANGUAGE: CAMERA ADJUSTMENT English,Japanese,German, French Russian, Portuguese, Spanish, Chinese. SHUTTER/AGC SETUP MENU LANGUAGE LENS SHUTTER/AGC WHITE BAL DAY/NIGHT PICT ADJUST 2DNR LENS SETUP MENU LANGUAGE LENS SHUTTER/AGC WHITE BAL DAY/NIGHT PICT ADJUST 2DNR ENGLISH AUTO AUTO ATW AUTO   NEXT EXIT SAVE ALL Shutter has two options eitherNEXT AUTO or MANUAL EXIT Changes the settings of the internal lens..
PAGE 14
CAMERA ADJUSTMENT CAMERA ADJUSTMENT • MANUAL SETUP MODE: SHUTTER: AGC: SHUT+AGC No options selectable. 1/60 / 1/120 / 1/250 / 1/500 1/1000 / 1/2000 / 1/4000 1/10000 Shutter speed in fractions of a second. 6.00 / 12.00 / 18.00 / 24.00 / 30.00 36.00 / 42.00 / 44.80 AGC value in [dB] ATW FRAME: ENVIRONMENT: x0.50 / x1.00 / x1.50 / x2.00 Sets pull in frame for magnification Default setting is X1.
PAGE 15
CAMERA ADJUSTMENT CAMERA ADJUSTMENT LEVEL: 000-255 Specifies the R and B gain values for manual WB. The actual variable range is limited to the range from the low color temperature (approx. 1800K) to the high color temperature (approx. 10500K). Default setting is 58 • PUSH LOCK DAY/NIGHT Press down on joystick to set current scene as the white balance level. Use a grey card in front of lens to give a natural white level.
PAGE 16
CAMERA ADJUSTMENT CAMERA ADJUSTMENT Y LEVEL: C LEVEL: PICT ADJUST SETUP MENU LANGUAGE LENS SHUTTER/AGC WHITE BAL DAY/NIGHT PICT ADJUST 2DNR ENGLISH AUTO AUTO ATW AUTO   Picture and display controlNEXT settings EXIT PICT ADJUST MIRROR BRIGHTNESS CONTRAST SHARPNESS HUE GAIN NEXT SAVE ALL OFF 0 128 128 128 150 000-015 Adjustment of the Y filter strength. Default setting is 4 000-015 Adjustment of the C filter strength.
PAGE 17
CAMERA ADJUSTMENT CAMERA ADJUSTMENT This function compensates for darker areas surrounding the object to provide naturally sharp picture and improves contrast in bright/dark areas.
PAGE 18
CAMERA ADJUSTMENT MOTION AREA: ON: Make motion areas visible, OFF: Hide motion areas ENABLE Press enter to access the “dead band setting” screen, on-screen cursor moves in response to the inputs Left, Right, Up and Down to set the sensing area, or dead band for specified blocks. This allows you to specify and set an area of motion which is not rectangular in shape. Press and hold SET button 3 seconds to exit. CAMERA ADJUSTMENT Use Up/Down/Left/Right to move around.