Model 2052 Installation Manual 951.698.7887 www.HomeSelects.
5($' $1' 6 $ 9 ( 7+(6( ,16758&7,216 %HIRUH EHJLQQLQJ LQVWDOODWLRQ RI \RXU QHZ FHLOLQJ IDQ UHDG DQG IROORZ WKHVH VDIHW\ SUHFDXWLRQV ,I \RX DUH QRW IDPLOLDU ZLWK QDWLRQDO DQG ORFDO HOHFWULFDO FRGHV DQG EDVLF HOHFWULFDO ZLULQJ SURFHGXUHV ZH UHFRPPHQG WKDW \RX KDYH D TXDOLILHG \RXU QHZ FHLOLQJ IDQ HOHFWULFLDQ LQVWDOO Before you begin, TURN OFF THE ELECTRICITY.
This ceiling fan was not designed for installation in any location where it might be exposed to moisture or high humidity. Installation in this type of location could be UNSAFE, will most likely damage the fan and its finish... and will VOID YOUR WARRANTY. Every effort has been made to provide you with proper instructions for the safe installation of this ceiling fan. You could however, encounter situations or problems not covered in this manual.
6ORWWHG 6FUHZ 0RXQWLQJ %UDFNHW Have you TURNED OFF the Electricity? 1RQ 6ORWWHG 6FUHZ &DQRS\ Step 1 Attach the mounting bracket Remove the two non-slotted mounting screws on the top of the canopy. Back the two slotted screws out about half way. This will enable you to remove the mounting bracket from canopy (see figure 1). Install the mounting bracket on the electrical junction box in the ceiling using two machine screws, two washers and two lock washers (see figure 2).
Step 3 Attach the support assembly 6FUHZV &HLOLQJ &DQRS\ 6XSSRUW 5RG &RXSOHU This fan is designed to be mounted as a flush mount (for lower ceiling heights), or suspended. Flushmount (see figure 4) Loosen the set screws (2) in the support rod coupler located on the top center of the motor housing until the inside channel is clear. Remove and save the safety screw from the coupler. Place the ceiling canopy on top of the motor housing and secure with the three mounting screws.
Step 4 Hanging the Fan Body NOTE: Suspended Installation (follow steps 1-4), Flushmount Installation (go to step 4) 1 - Notice the half ball on the end of the support rod is grooved down one side. This Keyway fits over the small keyway pin on the inside of the mounting bracket and keeps the ceiling fan from spinning on the mounting bracket. 0RXQWLQJ %UDFNHW .
Step 5 Making the Electrical Connections :KLWH To operate your ceiling fan with the pull chain(s) and switches mounted on your fan, follow the instructions below: %OXH :KLWH *URXQG %ODFN *URXQG %ODFN Attach the GREEN wire (connected to the half ball) to the GROUND wire in the junction box. The GROUND wire is usually a bare copper wire without plastic insulation. It could also be covered in green plastic insulation (see figure 9).
Step 6 Fan Blade and Blade Arm Assembly Attach each fan blade to a blade arm with three 3/16” x 7.5 mm blade screws and three 3/16” fiber washers (see figure 11). DO NOT OVER TIGHEN THESE SCREWS. Screws should be tightened until the washers are compressed by the screw head. Hold the Blade Arm decorative side down and place the blade on top with the flat side of the blade facing down. Each screw is passed through the washer and blade and screwed into the blade arm.
Step 8 Light Fixture Installation Back off (loosen) the three screws on the electrical housing cover (see figure 13). Connect White wire to White wire, and Black wire to Blue wire using quick connectors. Press together firmly. Place light fixture onto fan, line up the 2 holes and rotate light fixture; Insert the screws and tighten. 7KUHH 6SHHG 6ZLWFK SXOO FKDLQ 6FUHZV :LUH 1XWV /LJKW )L[WXUH Each of the above connections should be made as tight as possible using the proper size plastic wire nuts.
Optional Wiring Diagrams )DQ FRQWUROOHG ZLWK ZDOO VZLWFK DQG /LJKW FRQWUROOHG DW IDQ Figure 15 illustrates the wiring used to control the fan with a wall switch plus an optional light fixture controlled at the fixture. Figure 16 illustrates the wiring used to control fan with the pull chain on the electrical switch housing plus an optional light fixture with a wall switch. FAN LIGHT Figure 17 illustrates the wiring used to control the fan and optional light fixture with separate wall switches.
Your new ceiling fan is now ready for use. Reset your circuit breaker and restore power to the circuit. See the Operation Instructions below to review the function of each control on your fan. Operation Instructions The three speed pull chain located on the switch housing (see figure 13) controls the speed of your fan. When the fan is OFF, pull the chain once for HIGH speed, twice for MEDIUM speed, three times for LOW speed and fourth time to turn it off again.
0RXQWLQJ %UDFNHW 6XSSRUW 5RG &RWWHU 3LQ 6DIHW\ 3LQ &DQRS\ 6FUHZV &HLOLQJ &DQRS\ 0RWRU &RXSOHU 0RWRU $VVHPEO\ 6ZLWFK +RXVLQJ 5HYHUVH 6ZLWFK %ODGH 6FUHZV DQG /RFN : DVKHUV 6ZLWFK +RXVLQJ 6FUHZ 7KUHH 6SHHG 6ZLWFK SXOO FKDLQ %ODGH $UP 7KXPE 6FUHZV /LJKW )L[WXUH /LJKW 6ZLWFK SXOO FKDLQ *ODVV 6KDGHV %XOEV 12 %ODGH
