Installation Guide

17
Controls
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Note:Hoodretainslastspeedsettingwhenaspiration
switch is turned off.
Description of control panel
1. Light Button
PresslampbuttontoturnONthelightonHigh 
 Intensity(LampstatepreviouslyOFF).
PresslampbuttontoturnONthelightonLow 
 Intensity(LampstatepreviouslyON).
PresslampbuttontoturnOFFthelight(Lampstate 
 previouslyON).
2. Timer Button
Thedefaulttimersettingis10minutes,anditcanbe 
adjusted between 60 minutes and 1 minute.
Afterpressingthetimerbutton,thecontrolenterstoa
timer setup mode, and user can adjust the timer
 countdowntimewiththe“+”and“-”buttonswithin5 
 seconds.Thetimercanbeinitiatedimmediately 
pressing the timer button, after setting the timer
duration or pressing the timer button twice (default 10
minutes setting).
If no action occurs within 5 seconds, the countdown
will start.
Duringthetimersetupthe“+”and“-”buttonsare 
dedicated to the timer and no motor action will occur.
Oncethetimerisinitiated,itcanbecancelledby 
pressing the timer button again.
3. Display
Shows the hood settings.
Thedisplaywillbelitatlowintensitywhenthehood 
is not operating.
Pressing any key the display will light up at high
intensity.
Thedisplaywillbelitathighintensitywhenthehood 
is operating.
If no key is pressed within a minute the display will
return to being lit at low intensity.
4. “-” Button. Speed Decrease / OFF
Thisbuttonisusedtodecreasethefanspeed,or 
 turnOFFthefan.
ThefanwillturnOFFifthe“-”buttonispressedand 
 thehoodwasintherstspeed.
Ifthefanisatsecondspeedandthe“-”buttonis 
 pressed,thefanwillbesettorstspeed.
Ifthefanisatthirdspeedandthe“-”keyispressed, 
the fan will be set to second speed.
Ifthefanisatfourthspeedandthe“-”buttonis 
pressed, the fan will be set to third speed.
IfthefanisOFFandthe“-”buttonispressed,the 
control backlight will light up.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5. “+” Button. Speed Increase / ON
Thisbuttonisusedtoincreasethefanspeed,orturn
 ONthefan.
ThefanwillturnONifthe“+”buttonispressedand 
 thehoodwasOFF.
Ifthefanisatrstspeedandthe“+”buttonis 
pressed, the fan will be set to second speed.
Ifthefanisatsecondspeedandthe“+”buttonis 
pressed, the fan will be set to third speed.
Ifthefanisatthirdspeedandthe“+”buttonis 
pressed, the fan will be set to fourth speed.
Ifthefanisatfourthspeedandthe“+”buttonis 
pressed, a beep will sound.
Clock programming
Theclockcanbereprogrammedatanytimeexcept 
during an active timed function.
Theclockcanbedisplayedinatwelvehourformatand
valid clock times are from 1:00 to 12:59.
Theclockcanbereprogrammedpressingthe“Timer”
button for 3 seconds, and after, the clock can be
 adjustedwiththe“+”and“-”buttons.
Theusercanhaveminuteincrements/decrementsof1
 minute,butiftheuserkeeppressingthe“+”/”-”buttons
 formorethan1second,theincrements/decrementswill
be of 5 minutes.
During this option the control will round to the nearest 5
minutes.
Theusercannishonreprogrammingtheclockpressing
 the“Timer”button.
After1minuteofnobuttonpressedthecontrolwill 
accept the programmed clock time and will add one
minute to the set clock.
•
•
•
•
•
•
•
•
•
•
•
•