User Manual

ManualsBrandselfe ManualsDog Collarelfe FW651A Remote Training Dog Collar

Please read the quick start before beginning

Important Safety Information Overview Setting Up the Product

Quick Start

Model: FW651A

Remote Training

Dog Collar

1. Charge the Remote and the Receiver Collar.

2. Prepare the Remote and turn it on.

3. Prepare the Receiver Collar and turn it on.

4. Test button functions before putting it on dog.

5. Test Vibration function.

6. Pair the Remote and the Receiver Collar, pair them when the product

loses its code or pairs with a second collar.

Please use the Output : DC 5V 500-800mA charger to charge the product.

Don’t use a charger that does not meet the speciﬁcations to charge the

product.

Before you can use the Dog Training Collar, you

must set up the product using the steps below:

Note:

Prepare the Remote

Turn ON/OFF the Remote

1. Plug in and fully charge the Remote and the Receiver collar.

For the initial charge,be sure to charge it for 4 hours.

Subsequent charges only take 2-3 hours.

2. When fully charged, the red LED on the Receiver Collar will become

green. The Battery Display of the Remote will stop cycling and become

steady.

Charging the Remote and the Receiver Collar

1. Press and hold the ON/OFF button to turn the remote ON.

2. LCD will be lighted, and shows the information of current channel,

battery power and levels. If not, please charge the remote.

3. Press and hold the ON/OFF button to turn the remote OFF.

Turn on the Receiver Collar

• Press the On/Off Button until the Green LED light comes on.

• In normal mode, the Green LED will ash every 4 seconds, indicating

the Receiver Collar is on and ready to receive a signal from the Remote.

Turn off the Receiver Collar

• Press and hold the On/Off Button until the Red LED light shuts off

(This takes approximately 3 seconds).

• Release the On/Off Button.

NOTE:

To extend the life of the batteries, please turn the Receiver Collar off when

it is not in use.

Function Test

We recommend you experience ﬁrsthand how the different levels feel on

yourself. Please always starts at the lowest level and work your way up to

your personal comfortable levels.

1. Place the collar receiver on your hand or your leg.

2. Hold your remote approximately 60cm (2 ft). from the training collar.

Press the Vibration Button continuously for 1 to 2 seconds.

You should feel continuous vibration.

3. Starting at level 1,press the Vibration Button.

4. Increase the level until the sensation begins to feel uncomfortable.

NOTE: Continuous stimulation will transmit for no more than 10 seconds.

To reactivate, release and press the button again.

• The Vibration Level can be adjusted from level 1 to 8, please adjust it

properly as per your dog’s reaction.

• It is not recommended to press and hold the Vibration+Tone Button

too long to avoid physical or psychological hurt to the dog.

Note:

1. Use the switch on the Remote to select Dog 1 .

2. With the Remote turned on and the Receiver Collar turned off, press

and hold the ON/OFF Button on the Receiver Collar for 4-5 seconds.

3. The Red & Green LED will blink for about 10 seconds indicating that it

is ready for pairing.

4. Press and hold the Tone Button and the tone+Vibration Button at the

same time for 2-3 seconds, the Green Led on the Receiver Collar will

blink for 5 times indicating successful pairing.

Pair the Remote and the Receiver Collar

Tips: 1. Excessive charging will shorten battery life. Only charge them

when batteries are low.

2. When you’re not using the collar, please turn it off to increase

the battery life.

The FW651A dog training collar is designed to let dogs live safely,

happily and get along with people more harmoniously.

Aggressive dogs can cause severe injury and even death to their owner

and others. If you are unsure whether this product is appropriate for

your dog, please consult your veterinarian or certiﬁed trainer.

Do not use with aggressive dogs

Please read and follow the instructions in this manual. Proper ﬁt of the

collar is important. A collar worn for too long or made too tight on the

pet’s neck may cause skin damage ranging from redness to pressure

ulcers. This condition is commonly known as bed sores.

• Avoid leaving the collar on the dog for more than 12 hours per day.

• When possible reposition the collar on the pet’s neck every 1 to 2 hours.

• Never connect a lead to the electronic collar; it will cause excessive

pressure on the contacts.

• If a rash or sore is found, discontinue use of the collar until the skin

has healed.

• If the condition persists beyond 48 hours, see your veterinarian.

• This product is not a toy, please keep away from children.

• This product is only for use with healthy dogs.

Risk of skin damage

It is vitally important that you and your dog remain safe while learning

during on-leash training. Your dog should be on a strong leash, long

enough for him to attempt to chase an object, but short enough for him

not to reach a road or other unsafe area. You must also be physically

strong enough to restrain your dog when he tries to chase.

Safety during on-leash training

WARNING

CAUTION

A. Mode indication

B. Battery Display

C. Vibration Level +

D. Vibration Level -

E. On/Off Button

F. Channel Display

G. Channel Conversion Switch

H. Vibration Level Display

I. Tone Button

J. Vibration + Tone Button

K. Vibration Button

L. Charging Port

Remote

Q. Charging Port (with cover)

R. On/Off Button

S. LED Indicator

Receiver Collar

Tone: sends an adjustable level vibration and non-adjustable level tone

simultaneously to the Receiver Collar.

Vibration: sends 1-8 adjustable levels of vibrate stimulation to the

Receiver Collar.

Vibration+Tone Button: sends a vibration and tone with non-adjustable

level to the Receiver Collar.

Slide up, control dog 1, slide down,control dog 2.

Long press to turn on, long press to turn off.

Press to increase the Vibration Level.

Press to decrease the Vibration Level.

1 2 3 4 5 6

Summary of content (2 pages)

PAGE 1
Important Safety Information Quick Start The FW651A dog training collar is designed to let dogs live safely, happily and get along with people more harmoniously. A WARNING Do not use with aggressive dogs Model: FW651A Remote Training Dog Collar C G D H I Safety during on-leash training E It is vitally important that you and your dog remain safe while learning during on-leash training.
PAGE 2
Collar Fitting The unit needs to be charged under any of situations below Please ﬁt the collar properly so that the collar presses ﬁrmly against the dog’s skin. When properly ﬁtted, you can be able to put a ﬁnger in between the Receiver Collar and dog’s neck. Too loose: the Receiver Collar will move around the dog’s neck, the vibration mode may not be able to work effectively. Too tight: it may cause dog’s to breathe hard. Caution: 1.