OPERATION Push Button OFF Bunion Turn off the fan. Low Speed Button Start the fan at low speed . It is suitable for simmering and cooking which does not make much steam. Medium Speed Button Start the fan at medium speed. This is ideal for ventilation during standard cooking operation. High Speed Button Start the fan at high speed. This is ideal for ventilation when a high density of smoke or steam has been produced. Light Button Used for turning on/off the light.
Electronic Button (Lighting) () ON/OFF key Press this key to turn power/motor on and Off w« Power down key On working condition, press this key to decrease the power one level wi Power up key On working condition, press this key to increase the power one level ® Delay key When motor is on working condition, press one time to set 5 minutes delay, press another time to turn the delay function off. 8; Light key Press one time for turning the lights on, press another time to turn the lights off.
1. 2 Touch control . Digital display key Power down key Power up key Delay key On stand-by and working condition, press this key for 3s, the digital display blinks, we can set the delay power off time from I minute to 9 minutes; press the key again to save the setting. If 10s no pressing, then the setting would be saved automatically. When the motor is on and the delay setting is saved , we can still adjust the setting, and the display window will display the countdown time.
ON/OFF key Power down key On working condition, press this key to decrease the power one level, ( the ON/OFF key light would blink slower than the power was not decreased). I@ wi Power up key On working condition, press this key to increase the power one level, ( the ON/OFF key light would blink faster than the power was not increased). (© Delay key When motor is on working condition, press one time fo set 5 minutes delay, press another time to turn the delay function off.
Timer button Time setting, Press anf hold in stand-by mode. This will go into time setting function.Hour display will flash. SHOO 1.0n stand-by and working condition, the LED would be shut off if 2 minutes without pressing, press any key to turn the LED on. 2.When key lights are off, only ON/OFF and lights key can turn the LED on, On stand-by condition, any key can turn the LED on, all operation based on LED is on function.
® ¢i ON/OFF key Connect power in the standby state, press the key for 0.5 seconds to enter the starting state; when the motor in running state, press one time to enter “I-minute delay shutdown count down” state, the motor would turn off immediately if you press again Speed key press this key to change motor level from low level to middies and high level, it is circle change. Plus key press the key to increase motor level. Minus key press the key to decrease motor level. Timer 1.
ON/OFF key Low speed button Medium speed button High speed button Long touch the button for 5 seconds in off mode, the gesture control function will be locked. Repeat this action, it will be turned on. Light key AUTO-CLEAN Please first touch ON/OFF button, then touch "Auto-Clean" button on the panel. The display mention heating time of 9 minutes and begin to count down. The light for auto clean with start blinking. After preheat time of 9 minutes. The indicating lamp of low speed were lit at the same time.
MAINTENANCE Before cleaning switch the unit off and pull out the plug. IL Regular Cleaning Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or stiff brush to clean the unit. II. Bulb Replacement switch the unit off and unplug the appliance. 2.Remove the lamp cover by unscrewing the 2 screws. 3.Unscrew the incandescent bulb 4.Replace with the same type and rated bulb/lamp E14 Incandescent Bulb: (220V E14 Max 40W).
III. Aluminum and charcoal filters replacement In order to install the carbon filter, the grease filter should be detached first. Press the lock and pull it downward. MONTHS 0 MAX.65 °C Aluminum filters: To avoid fires, clean thoroughly once a month or whenever the display pilot lights up (if fitted). To do so,remove the filters and soak in hot water and detergent for an hour If using a dishwasher,position the filters vertically to improve the cleaning process. VI.
TROUBLE SHOOTING Fault Cause Solution . The fan blade is jammed. | Switch off the unit and da rot wort : repair by qualified The motor is damaged. service personnel only. : Replace the LED light Both light and fan Light bulb burn. with correct rating. do not work Power cord is loose. Plug im io the p wore The fan blade i: Theta’ Aden Switch of the unit and repair by qualified Serious Vibration The fan motor is not service personnel only. of the unit fixed tightly. LL.
