ETG5200 ETG3500 ETG2500 (list of variations available in the manual) SOLID STATE FM TRANSMITTER Rev. 03- 11/03/2022 Cod.
Via G. Amendola 9, 44028 Poggio Renatico Ferrara (Italy) UNI EN ISO 9001:2008 certified company C.C.I.A.A. 101 216, Tax code and VAT reg. no. IT00415540384 Certificate No.102222A Please remember to register the product purchased on http://www.elenos.com/product-registration/ Please contact technical support service for information and assistance: Elenos Ph : +39 0532 829965 Fax : +39 0532 829177 E-mail : info@elenos.com Internet web site : www.elenos.com Elenos USA 1315 nw 98th Ct.
Revisions No.
Series models Transmitter 4 Number of modules Number of drivers Maximum output power ETG5200 7 1 5200W ETG5000 7 1 5000W ETG4000/5 ETG3500/5 ETG3000/5 ETG2500/5 ETG2000/5 ETG1800/5 ETG1500/5 ETG1200/5 ETG1000/5 ETG800/5 ETG500/5 7 1 Equal to the rated value ETG3500 5 1 3500W ETG3000/3.5 ETG2500/3.5 ETG2000/3.5 ETG1800/3.5 ETG1500/3.5 ETG1200/3.5 ETG1000/3.5 ETG800/3.5 ETG500/3.5 5 1 Equal to the rated value ETG2500 4 1 2500W ETG2000/2.5 ETG1800/2.5 ETG1500/2.5 ETG1200/2.
Contents 1 Informative letter...................................................................................................................... 7 1.1 Personnel in charge ........................................................................................................... 7 1.2 Warranty ............................................................................................................................ 8 1.3 Exclusion .........................................................................
Contents
1 Informative letter Dear Customer, Thank you for choosing an Elenos product. ELENOS s.r.l. produces solid state VHF/FM sound broadcasting transmitters ranging from minimum power of 10W to maximum power of 30kW, exchange units, remote control units, etc. The equipment has been produced to ensure constant performance over time, provided all periodic checks and simple maintenance repairs required are carried out. This equipment is very intuitive and user friendly.
1.2 Warranty The products sold to the Customer by Elenos Srl are covered by a 24-month warranty from the FOB date of shipment from Elenos Srl; this warranty covers both the customer and any subsequent purchasers of the product, as long as it is kept in excellent condition, and covers all types of faults due to defective parts on the product itself. An essential condition for the warranty issued by Elenos Srl to operate effectively is the registration of the product by the Customer through the website www.
1.4 Exemption from liability The Customer is responsible for the installation, maintenance and inspection of the products, as well as checking that the climatic and environmental conditions in which the products are placed for their use are suitable and do not compromise operation, all according to the Elenos Srl instruction manual delivered with the purchased product.
Informative letter
2 EC Marking For launching all its products on the market, ELENOS s.r.l respects the procedures envisaged by the 1999/5/EC Directive. This includes the following: • Technical documentation available exclusively to the Control Authority for 10 years after the launch on the market of the last equipment produced for that type. Such documentation contains the product description, the drawings, the electrical diagrams, circuits, etc.
EC Declaration of Conformity According to Directive 1999/5/EC (R&TTE) We : ELENOS s.r.l. - via G.Amendola, 9 – 44028 Poggio Renatico (FE) - Italy Declare under our sole responsibility that the product: ETG5200, ETG5000, ETG4000/5, ETG3500/5, ETG3000/5, ETG2500/5, ETG2000/5, ETG1800/5, ETG1500/5, ETG1200/5, ETG1000/5, ETG800/5, ETG500/5 ETG3500, ETG3000/3.5, ETG2500/3.5, ETG2000/3.5, ETG1800/3.5, ETG1500/3.5, ETG1200/3.5, ETG1000/3.5, ETG800/3.5, ETG500/3.5 ETG2500, ETG2000/2.5, ETG1800/2.5, ETG1500/2.
LIST OF COUNTRIES WHERE THIS APPARATUS CAN BE USED AT FI LV BE FR MT BG GB NL CH GR NO CY HU PL CZ IE PT DE IS RO DK IT SK EE LT SI ES LU SE AUTHORIZATION IS REQUIRED TO USE THIS EQUIPMENT Other types of certification are managed according to the apparatus use country.
EC Marking
3 Safety All ELENOS s.r.l products are compliant with the safety standards required for this type of equipment. 3.1 Precautions The user must follow also the precautions listed below: • The original configuration of the equipment must absolutely not be modified. Upon receipt, check that the supply is compliant with the order specifications and if not, report it to ELENOS s.r.l. immediately.
The equipment is directly connected to the “building installation” Between the equipment and the “building connection” there is an interposed structure 16 • To ensure its correct operation do not cover the ventilation grids on the equipment. Do not place the equipment close to heat sources, flammable products or closed installations without appropriate ventilation. • All firefighting and safety rules for the room where the equipment is located must be carefully followed.
3.2 First aid This paragraph is NOT a comprehensive guide to first aid procedures; it is intended as a summary to be used as a reference. It is the duty of all staff using this device to perform appropriate first aid procedures in order to prevent avoidable deaths. 3.2.1 Treatment of electrical burns 3.2.1.1 Extensive burns and skin cuts • Cover the area with a clean sheet or cloth. • Do not break blisters, remove tissue, remove adhered particles of clothing, or apply any ointment.
fig.c1 fig.c2 C) Circulation (fig. c1): • check the pulse (fig. c1) • if absent, start cardiac massage (fig. c2) • compress the chest every 1.5 - 2 seconds • if a rescuer is present, perform 15 compressions in approximately 80 seconds, + 2 quick blows • if there are two rescuers, perform 5 compressions in approximately 60 seconds, + 1 quick blow (fig. c3) WARNING : Do not interrupt the rhythm of compressions when the second person is performing artificial respiration. fig.c3 3.2.2.
equipment model. Use cables of an appropriate size with respect to the rated absorbed current. Earth connection must be performed according to the applicable laws. Special care must be applied to the earth connection of the antenna system since it is exposed to electrical atmospheric events. Never forget that despite the earth connection of the equipment frame and the whole antenna system, it is always dangerous to operate on the equipment in the event of bad weather with atmospheric discharge.
Safety
4 Product presentation 4.1 Marks and labels 1 ICEFET ® – Design technology of RF modules that ensures high efficiency in the whole range of output powers, at very low temperatures, hence increasing the life of MOS devices. 2 LIFEXTENDER ® – Optional system within the equipment. Once operating, it allows safe operation even in extremely severe environmental conditions.
5 NAMEPLATE – Plate where the main characteristics of the equipment are reported: manufacturer, product model, power supply type, power consumption, EC marking, serial number, final test date, name of the tester.. Warning: do not remove this nameplate. 6 SUPPORT LABEL – Label indicating the details for Elenos support. 7 DISPOSAL LABEL – Label indicating that the equipment must be disposed of properly and according to the laws in force.
4.2 Front panel 1 OLED technology display – Graphic display showing the operating parameters and selected functions my means of an encoder. 2 Encoder – Multifunction handle allowing navigation through function menus and modification of operating parameters. 3 Key selector – It can be set on LOCAL (controllable through the front panel) or REMOTE (controllable through PC) mode, by rotating the key supplied with the equipment.
[8] [10] [7] [4] [1] [2] [5] [9] [3] 24 Product presentation [6]
4.3 Rear Panel 1 Power supply terminal board – Terminal board with 6 contacts connecting the three internal power supplies. For details of the connection mode, please refer to section “Quick guide for commissioning”. 2 Earthing screw – Eyelet for earthing the equipment, located behind the flange of the output coaxial connector. 3 Rear fans– Fans for cooling the equipment. There are 3 of them: sizes 120x120x38 mm, 12-28 VDC, 306 m3/h. 4 RF connector – Type 7/8.
[11] [10] [9] [3] [12] [13] [14] [6] 26 [5] [7] [8] [1] [2] [4] Product presentation
5 Quick instructions for commissioning 5.1 Installation 1 If you have a rack, insert and attach the equipment into it (use the fixing holes on the side fins). If you don’t have a rack, please make sure that: • the equipment is located away from the room walls so that the installation and maintenance operations can be conveniently carried out; • the ventilation grids are not clogged; • the equipment is far from heat sources or flammable products; • the equipment is isolated from contact with liquids.
WARNING: the connection operations of the power supply cable to the equipment terminal boards must be performed with the cable UPLUGGED from the electrical mains or WITHOUT VOLTAGE exclusively. Should the operator require to disconnect the equipment from the mains, go backwards always disconnecting first the electrical plug and then removing the terminals from the terminal board. Neutral CONFIG.
CONFIG.3 Phase1 Phase2 ph1 210V N L1 N1 L2 N2 L3 N3 ph3 ph2 Network configuration available Configuration to be implemented on the transmitter terminal The lines of the three power supplies (L1, L2, L3) must be connected together to the phase 1 of the electrical mains, while the three neutrals (N1, N2, N3) must be connected together to the phase 2 of the electrical mains. CONFIG.
Suggested AC Input Connections With 4-Terminal Block To make your installation easier, we recommend the use of a 3-terminal or 4-terminal power distribution block, depending on whether you have single or three phase power. The diagrams below are our suggested wiring configurations.
30 5 D 4 3 L1 N1 N PSU 1 - 1 L1 L + 2 L2 N2 N L3 N3 L + C PSU 2 E L + B C N - Out 30 to 50 V dc Quick instructions for commissioning E D 400 Volt L2 50 Hertz L3 3 Phases PSU 3 B N - E To SHUNT Board Silvered Bar Via G. Amendola 9 44028 Poggio Renatico (FE) Italy Tel. +39 0532 829965 Fax +39 0532 82917 Website WWW.ELENOS.COM A A Description : SCH Code : MAINS WIRING (400V - 3Ph) PCB Code : Proj. Eng. L.
5 D 4 3 230 Volt 50 Hertz N 1 Phase L N1 N PSU 1 - 1 L1 L + 2 D L2 E N2 L3 N3 L + C PSU 2 N - E Out 30 to 50 V dc Quick instructions for commissioning L + B C PSU 3 B N - E To SHUNT Board Silvered Bar Via G. Amendola 9 44028 Poggio Renatico (FE) Italy Tel. +39 0532 829965 Fax +39 0532 82917 Website WWW.ELENOS.COM A A Description : SCH Code : MAINS WIRING (230V - 1Ph) PCB Code : Proj. Eng. L.
32 5 D 4 3 L1 N1 N PSU 1 - 1 L1 L + 2 L2 N2 L3 L3 N3 L + C PSU 2 E L + B C N - Out 30 to 50 V dc Quick instructions for commissioning E D 230 Volt L2 50 Hertz 3 Phases PSU 3 B N - E To SHUNT Board Silvered Bar Via G. Amendola 9 44028 Poggio Renatico (FE) Italy Tel. +39 0532 829965 Fax +39 0532 82917 Website WWW.ELENOS.COM A A Description : SCH Code : MAINS WIRING (230V - 3Ph) PCB Code : Proj. Eng. L.
4 Connect the equipment’s RF output to the antenna cable (to check the equipment’s performance it can be connected to a dummy load able to dissipate the power delivered by the equipment). WARNING: Before connecting the Antenna System Cable to the Elenos transmitter, please make sure that the cable, connectors and antenna are grounded according to manufacturers recommendations.
5.2 Factory settings The equipment comes with the following default factory settings. If they correspond to your requirements, just put the machine in RF ON. Should you need to change the parameters, please refer to paragraph “Main parameter setup”. ETG EQUIPMENT VERSION FACTORY SETTINGS With Stereo Coder board (it works With Stereo Coder boin MPX,Stereo,Mono modes) ard + AES/EBU (it works in MPX,Stereo,Mono,AES/ EBU modes) Output power (TRG) Maximum value Maximum value Frequency 98.000 MHz 98.
5.3 Main parameter setup To set the parameters from the display the equipment must be in LOCAL mode. It is also possible to partially view the menus in REMOTE mode, provided that the parameter “SHOW D. : ALWAYS” is present (for details, refer to the paragraph “User interface” on the “System config.” screen). To switch from LOCAL to REMOTE mode rotate the supplied key on the selector. In LOCAL mode, the blue led turns on and the screen “TX control panel” is automatically displayed.
9 5.3.1 Frequency setup In the “TX control panel” screen, rotate the encoder until it selects the frequency set. Press once to enter the adjustment mask. The frequency range is now selected and can be modified: rotate the encoder clockwise/anticlockwise to increase/decrease the value respectively. Press the encoder to confirm. The dialog box will indicate the new operating frequency set.
10 5.3.2 Power setup In the “TX control panel” screen, rotate the encoder until it selects the power set. Press once to enter the adjustment mask. The power field is now selected and can be edited: rotate the encoder clockwise/anticlockwise to increase/decrease the value respectively. Press the encoder to confirm. The dialog box will indicate the new operating power set.
11 5.3.3 Audio signal setup According to the type of audio signal used to modulate, select the relative input. In the “TX control panel” screen, rotate the encoder until it selects the fifth tab of the horizontal menu. Press once to make the field editable. Then, rotate the encoder to view the available options: 5.3.3.1 MUTE Mode which mutes all inputs. It is usually used during technical interventions. 5.3.3.
E E Quick instructions for commissioning 39
E E 40 Quick instructions for commissioning
12 5.3.4 Audio level setup In the “TX control panel” screen, rotate the encoder until it selects the audio level set. Press once to make the field editable. Rotate the encoder until the amplifier is at the minimum level ( - 15dB). Apply the audio signal. Slowly increase the gain until the Vu-Meters reach 0dB level in accordance with the audio signal peaks. Confirm the value by pressing the encoder.
13 5.3.5 Start-up In the “TX control panel” screen, rotate the encoder until it selects the second tab of the horizontal menu to turn it on. Press the encoder until the RFON message appears. In LOCAL mode the following must occur to have a compliant situation: • The 4 warning lights (ITLK, -3dB, CLIP, NOAU) must be off; • The frequency set must be the desired one; • The direct power must be the desired one; • The reflected power must be null or low level; • The Vu-Meters must be set to 0dB.
6 Intervention inventory 6.
6.
6.
6.4 Intervention request sheet The following pages report the sheets to be filled in and attached to the product should it need to be sent to ELENOS for checks and/or repairs. The correct and detailed completion of the sheet will allow us to detect the problem more quickly.
FAILURE SHEET To be sent with the equipment to: ELENOS S.r.l. Via G. Amendola, 9 44028 Poggio Renatico (FERRARA) Italy Serial Number : Date of production : ALARMS LIST (Main Menù) - Active alarms 0) A 1) A 2) A 3) A .. A EVENTS HISTORY (Main Menù) - Latest events 99) 98) 97) 96) ... VIEW TX PARAMETERS 1 (Main Menù) Freq (MHz) Targ (W) Profile Fwd (W) Dev. (KHz) Refl (W) Eff. (%) Itot (A) WTime (h) Vds (V) WFans(h) Temp. (C) FanSp (%) VIEW TX PARAMETERS 2 (Main Menù) Device n.
FAILURE SHEET To be sent with the equipment to: ELENOS S.r.l. Via G. Amendola, 9 44028 Poggio Renatico (FERRARA) Italy Serial Number : Date of production : ALARMS LIST (Main Menù) - Active alarms 0) A 1) A 2) A 3) A .. A EVENTS HISTORY (Main Menù) - Latest events 99) 98) 97) 96) ... VIEW TX PARAMETERS 1 (Main Menù) Freq (MHz) Targ (W) Profile Fwd (W) Dev. (KHz) Refl (W) Eff. (%) Itot (A) WTime (h) Vds (V) WFans(h) Temp. (C) FanSp (%) VIEW TX PARAMETERS 2 (Main Menù) Device n.
FAILURE SHEET To be sent with the equipment to: ELENOS S.r.l. Via G. Amendola, 9 44028 Poggio Renatico (FERRARA) Italy Serial Number : Date of production : ALARMS LIST (Main Menù) - Active alarms 0) A 1) A 2) A 3) A .. A EVENTS HISTORY (Main Menù) - Latest events 99) 98) 97) 96) ... VIEW TX PARAMETERS 1 (Main Menù) Freq (MHz) Targ (W) Profile Fwd (W) Dev. (KHz) Refl (W) Eff. (%) Itot (A) WTime (h) Vds (V) WFans(h) Temp. (C) FanSp (%) VIEW TX PARAMETERS 2 (Main Menù) Device n.
