User Manual

ManualsBrandsElektron ManualsDrum MachineSyntakt - 12 VOICE DRUM MACHINE, SYNTHESIZER, SEQUENCER AND GROOVE MACHINE

Table Of Contents

1. INTRODUCTION
- 1.1 CONVENTIONS IN THIS MANUAL
2. THE SYNTAKT
3. PANEL LAYOUT AND CONNECTORS
- 3.1 FRONT PANEL
- 3.2 REAR CONNECTORS
- 3.3 SETTING UP AND STARTING THE SYNTAKT
4. QUICK START
- 4.1 PLAYING THE FACTORY PRESETS
- 4.2 TEMPO
- 4.3 USING KEYBOARD MODE
- 4.4 USING MUTE MODE
- 4.5 EDITING PARAMETERS
5. SYNTAKT SOUND ARCHITECTURE
- 5.1 DIGITAL VOICE TYPE
- 5.2 ANALOG DRUM AND ANALOG CYMBAL VOICE TYPES
- 5.3 SEND EFFECTS
- 5.4 ANALOG FX BLOCK
  - 5.4.1 ANALOG FX BLOCK ROUTING
6. OVERVIEW OF THE SYNTAKT DATA STRUCTURE
- 6.1 +DRIVE
- 6.2 DATA STRUCTURE
- 6.3 ABOUT THE TRACKS
7. INTERACTING WITH THE SYNTAKT
- 7.1 SCREEN NAVIGATION
- 7.2 TRIG KEYS
- 7.3 ROTARY ENCODERS
- 7.4 KEY BEHAVIOR
- 7.5 PARAMETER EDITING
- 7.6 QUICK SCROLLING
- 7.7 COPY, CLEAR, AND PASTE
- 7.8 THE NAMING SCREEN
  - 7.8.1 POP-UP NAMING
- 7.9 KEYBOARD MODE
  - 7.9.1 KEYBOARD SETUP MENU
- 7.10 MUTE MODE
- 7.11 TRIG MODIFIERS
  - 7.11.1 SETTING UP TRIG MODIFIERS
  - 7.11.2 USING TRIG MODIFIERS
- 7.12 MIDI NOTES
- 7.13 OVERBRIDGE
- 7.14 CLASS COMPLIANT DEVICE
- 7.15 BACKING UP THE SYNTAKT
  - 7.15.1 BACKING UP PROJECTS AND SOUNDS
  - 7.15.2 TRANSFERRING BACKED UP FILES TO YOUR ELEKTRON DEVICE
8. PATTERNS AND SOUNDS
- 8.1 THE +DRIVE SOUND LIBRARY AND THE SOUND POOL
  - 8.1.1 ADDING SOUNDS TO THE SOUND POOL
- 8.2 PLAYING A SOUND
  - 8.2.1 PLAYING A SOUND USING AN EXTERNAL MIDI DEVICE
- 8.3 EDITING A SOUND
- 8.4 LOADING A SOUND
- 8.5 SAVING A SOUND
- 8.6 THE SOUND MENU
9. THE SEQUENCER
- 9.1 SEQUENCER TEMPO
- 9.2 BASIC PATTERN OPERATIONS
  - 9.2.1 SELECTING BANK AND PATTERN
  - 9.2.2 PATTERN CONTROL
- 9.3 EDITING A PATTERN
- 9.4 MICRO TIMING MENU
- 9.5 RETRIG MENU
- 9.6 PATTERN MENU
- 9.7 QUANTIZE MENU
- 9.8 METRONOME MENU
- 9.9 SCALE MENU
  - 9.9.1 PER PATTERN MODE
  - 9.9.2 PER TRACK MODE
- 9.10 SEQUENCER FEATURES
- 9.11 CHAINS
10. AUDIO TRACK PARAMETERS
- 10.1 EDITING THE AUDIO TRACK PARAMETERS
- 10.2 TRIG PARAMETERS PAGE
- 10.3 SYN PAGE
- 10.4 FLTR PAGE 1
- 10.5 FLTR PAGE 2
  - 10.5.1 DEL
- 10.6 AMP PAGE 1
- 10.7 AMP PAGE 2
- 10.8 LFO PAGE 1
- 10.9 LFO PAGE 2
11. MIDI TRACK PARAMETERS
- 11.1 EDITING THE MIDI TRACK PARAMETERS
- 11.2 TRIG PARAMETERS PAGE
- 11.3 SYN PAGE
- 11.4 FLTR PAGE (CC VALUE)
- 11.5 AMP PAGE (CC SELECT)
- 11.6 LFO PAGE
12. FX TRACK PARAMETERS
- 12.1 EDITING THE FX TRACK PARAMETERS
- 12.2 TRIG PARAMETERS PAGE
- 12.3 SYN PARAMETERS PAGE
- 12.4 FLTR PAGE 1
- 12.5 FLTR PAGE 2
  - 12.5.1 DEL
- 12.6 AMP PAGE 1
- 12.7 LFO PAGE 1
- 12.8 LFO PAGE 2
13. DELAY, REVERB AND MIXER PARAMETERS
- 13.1 EDITING THE DELAY, REVERB AND MIXER PARAMETERS
- 13.2 DELAY
- 13.3 REVERB
- 13.4 MIXER (1/3)
- 13.5 MIXER (2/3)
- 13.6 MIXER (3/3)
14. SETTINGS MENU
- 14.1 PROJECT
- 14.2 MIDI CONFIG
- 14.3 SYSEX DUMP
  - 14.3.1 SYSEX SEND
  - 14.3.2 SYSEX RECEIVE
- 14.4 AUDIO ROUTING (GLOBAL)
- 14.5 SYSTEM
15. STARTUP MENU
- 15.1 TEST MODE
- 15.2 EMPTY RESET
- 15.3 FACTORY RESET
- 15.4 OS UPGRADE
- 15.5 EXIT
16. SETUP EXAMPLES
- 16.1 SYNTAKT WITH A MONOPHONIC BASS MACHINE
- 16.2 CONTROLLING A SYNTHESIZER USING THE MIDI TRACKS
17. USEFUL KEY COMBINATIONS (QUICK KEYS)
18. TECHNICAL INFORMATION
19. CREDITS AND CONTACT INFORMATION
APPENDIX A: MACHINES
- A.1 VOICE TYPES AND MACHINES
  - A.1.1 ASSIGNING A MACHINE TO THE ACTIVE TRACK
- A.2 DIGITAL MACHINES
- A.3 ANALOG DRUM MACHINES
- A.4 ANALOG CYMBAL MACHINES
APPENDIX B: MIDI
- B.1 TRACK PARAMETERS
- B.2 TRIG PARAMETERS
- B.3 SYN PARAMETERS
- B.4 FILTER PARAMETERS
- B.5 AMP PARAMETERS
- B.6 LFO PARAMETERS
- B.7 FX PARAMETERS
- B.8 VAL PARAMETERS
- B.9 MISC PARAMETERS
- B.10 FX TRACK PARAMETERS
APPENDIX C: LFO MODULATION DESTINATIONS
APPENDIX D: UNISON AND CHORD SETTINGS
APPENDIX E: KEYBOARD SCALES
INDEX

APPENDIX A: MACHINES

TUNE (Tune) osets the incoming note value. This parameter is bipolar. A setting of 0 leaves the pitch

unchanged.

WAVE (Wave Sweep) sweeps through the wavetable.

PNCH (Punch) adds a compressor-like envelope, which accentuates and distorts the sound.

DEC (Decay) sets the length of the decay phase of the machines internal amp envelope.

TYPE (Type) sets the unison mode and selects chord. For more information about the TYPE settings,

please see “APPENDIX D: UNISON AND CHORD SETTINGS” on page 108

BAL (Chord/Osc Balance) sets the interval mix and chord balance. If TYPE is set to UNISON, BAL

sets the amount of detune.

FENV (Filter Envelope) sets the depth of the machines ﬁlter envelope.

OVER (Overdrive) sets the gain amount into the digital overdrive.

Press and hold [FUNC] and then turn the DATA ENTRY knob for the WAVE parameter to

quickly jump between the basic waveforms Sine, Square, Triangle, and Saw.

SY TOY

TUNE (Tune) osets the incoming note value. This parameter is bipolar. A setting of 0 leaves the pitch

unchanged.

FORM (Form) approximates dierent physical materials and objects by altering the ratios/spacing

between the operators.

PNCH (Punch) adds a compressor-like envelope, which accentuates and distorts the sound.

DEC (Decay) sets the length of the decay phase of the machines internal amp envelope.

IMP (Impact) sets the modulation and feedback depth of the modulator. This parameter controls the

amount of additional overtones, basically the impact of a stroke against the material.

BRIG (Brightness) sets the level of the partial frequencies above the fundamental.

PAR (Partial Decay) controls the decay and end levels of the partials/impact.

OVER (Overdrive) sets the gain amount into the digital overdrive.

MIDI

The parameters for the MIDI machine are split over the SYN, FLTR and AMP PARAMETER pages.

MIDI (SYN page)

Here you can set the MIDI channel that the MIDI machine should use to send data. Bank and program

change values are also set here, together with a few standard CC parameters. The default value of

the parameters on this page is OFF, meaning they are disabled and do not send out any data. Press

and hold [FUNC] and then press the DATA ENTRY knobs to enable them. You can then use the DATA

ENTRY knobs to set the parameter values as usual. Disable the parameters again by repeating the

activation procedure.

Press [SYN] once to access this parameter page.