User Manual
Table Of Contents
- 06230350_DE
- 1. Allgemeines
- 1.1 Zu diesem Dokument
- 1.2 Symbolerläuterungen
- 1.3 Gewährleistung und Garantie
- 1.4 Haftungsbeschränkungen
- 1.5 Entsorgung des Gerätes
- 1.6 Produktschlüssel
- 1.7 Bestimmungsgemäße Verwendung
- 1.8 Sicherheit
- 1.9 Technische Daten
- 1.10 Aufbau und Funktion
- 1.10.1 Allgemeine Beschreibung
- 1.10.2 Blockdiagramm
- 1.10.3 Lieferumfang
- 1.10.4 Zubehör
- 1.10.5 Optionen
- 1.10.6 Die Bedieneinheit (HMI)
- 1.10.7 USB-Port Typ B (Rückseite)
- 1.10.8 Steckplatz für Schnittstellenmodule
- 1.10.9 Analogschnittstelle
- 1.10.10 Share-Bus-Anschluß
- 1.10.11 Sense-Anschluß (Fernfühlung)
- 1.10.12 Master-Slave-Bus
- 2. Installation & Inbetriebnahme
- 2.1 Transport und Lagerung
- 2.2 Auspacken und Sichtkontrolle
- 2.3 Installation
- 2.3.1 Sicherheitsmaßnahmen vor Installation und Gebrauch
- 2.3.2 Vorbereitung
- 2.3.3 Aufstellung des Gerätes
- 2.3.4 Anschluß an das Stromnetz (AC)
- 2.3.5 Anschluß von DC-Lasten
- 2.3.6 Erdung des DC-Ausgangs
- 2.3.7 Anschluß der Fernfühlung
- 2.3.8 Installation eines AnyBus-Schnittstellenmoduls
- 2.3.9 Anschluß der analogen Schnittstelle
- 2.3.10 Anschließen des „Share-Bus“
- 2.3.11 Anschluß des USB-Ports (Rückseite)
- 2.3.12 Erstinbetriebnahme
- 2.3.13 Erneute Inbetriebnahme nach Firmwareupdates bzw. längerer Nichtbenutzung
- 3. Bedienung und Verwendung
- 3.1 Personenschutz
- 3.2 Regelungsarten
- 3.3 Manuelle Bedienung
- 3.4 Fernsteuerung
- 3.5 Alarme und Überwachung
- 3.6 Bedieneinheit (HMI) sperren
- 3.7 Nutzerprofile laden und speichern
- 3.8 Der Funktionsgenerator
- 3.8.1 Einleitung
- 3.8.2 Allgemeines
- 3.8.3 Arbeitsweise
- 3.8.4 Manuelle Bedienung
- 3.8.5 Sinus-Funktion
- 3.8.6 Dreieck-Funktion
- 3.8.7 Rechteck-Funktion
- 3.8.8 Trapez-Funktion
- 3.8.9 DIN 40839-Funktion
- 3.8.10 Arbiträr-Funktion
- 3.8.11 Rampen-Funktion
- 3.8.12 UI- und IU-Tabellenfunktion (XY-Tabelle)
- 3.8.13 PV-Tabellenfunktion (Photovoltaik)
- 3.8.14 FC-Tabellenfunktion (Brennstoffzelle)
- 3.8.15 Fernsteuerung des Funktionsgenerators
- 3.9 Weitere Anwendungen
- 4. Instandhaltung & Wartung
- 5. Zubehör und Optionen
- 6. Service & Support
- 1. Allgemeines
- 06230350_EN
- 1. General
- 1.1 About this document
- 1.2 Explanation of symbols
- 1.3 Warranty
- 1.4 Limitation of liability
- 1.5 Disposal of equipment
- 1.6 Product key
- 1.7 Intended usage
- 1.8 Safety
- 1.9 Technical Data
- 1.10 Construction and function
- 1.10.1 General description
- 1.10.2 Block diagram
- 1.10.3 Scope of delivery
- 1.10.4 Accessories
- 1.10.5 Options
- 1.10.6 The control panel (HMI)
- 1.10.7 USB port type B (rear side)
- 1.10.8 Interface module slot
- 1.10.9 Analog interface
- 1.10.10 Share Bus-Connection
- 1.10.11 Sense connector (remote sensing)
- 1.10.12 Master-Slave bus
- 2. Installation & commissioning
- 2.1 Transport and storage
- 2.2 Unpacking and visual check
- 2.3 Installation
- 2.3.1 Safety procedures before installation and use
- 2.3.2 Preparation
- 2.3.3 Installing the device
- 2.3.4 Connection to AC supply
- 2.3.5 Connection to DC loads
- 2.3.6 Grounding of the DC output
- 2.3.7 Connecting the “Share” bus
- 2.3.8 Connection of remote sense
- 2.3.9 Installation of an AnyBus interface module
- 2.3.10 Connecting the analog interface
- 2.3.11 Connecting the USB port (rear side)
- 2.3.12 Initial commission
- 2.3.13 Commission after a firmware update or a long period of non-use
- 3. Operation and application
- 3.1 Personal safety
- 3.2 Operating modes
- 3.3 Manual operation
- 3.4 Remote control
- 3.5 Alarms and monitoring
- 3.6 Control panel (HMI) lock
- 3.7 Loading and saving a user profile
- 3.8 The function generator
- 3.8.1 Introduction
- 3.8.2 General
- 3.8.3 Method of operation
- 3.8.4 Manual operation
- 3.8.5 Sine wave function
- 3.8.6 Triangular function
- 3.8.7 Rectangular function
- 3.8.8 Trapezoidal function
- 3.8.9 DIN 40839 function
- 3.8.10 Arbitrary function
- 3.8.11 Ramp Function
- 3.8.12 UI and IU table functions (XY table)
- 3.8.13 PV table function (photovoltaics)
- 3.8.14 FC table function (fuel cell)
- 3.8.15 Remote control of the function generator
- 3.9 Other applications
- 4. Service and maintenance
- 5. Accessories and options
- 6. Service & Support
- 1. General
Page 6
PSI 9000 3U Series
www.elektroautomatik.de
ea1974@elektroautomatik.de
EA Elektro-Automatik GmbH
Helmholtzstr. 31-33 • 41747 Viersen
Germany
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
1.5 Disposal of equipment
A piece of equipment which is intended for disposal must, according to European laws and regulations (ElektroG,
WEEE) be returned to the manufacturer for scrapping, unless the person operating the piece of equipment or an-
other, delegated person is conducting the disposal. Our equipment falls under these regulations and is accordingly
marked with the following symbol:
1.6 Product key
Decoding of the product description on the label, using an example:
PSI 9 080 - 510 3U zzz
Fieldforidenticationofinstalledoptionsand/orspecialmodels
S01...S0x = Special models
HS = High Speed option installed
WC = Water cooling installed
Construction (not always given)
2U / 3U / 4U = 19" frame with 2U, 3U or 4U
T = "Tower" - vertical standing model
DT = "Desktop" model
R = "Rack mount" model in frame for wall mounting
Maximum current of the device in Ampere
Maximum voltage of the device in Volt
Series : 8 = Series 8000 or 800, 9 = Series 9000
Typeidentication:
PS = Power Supply, usually programmable
PSI = Power Supply Intelligent, always programmable
ELR = Electronic Load with Recovery
• Special devices are always derivations of standard models and can vary in output voltage and
current from those given.
• Identicationsprintedonthehousingsareusuallyabbreviatedcomparedtotheproductlabel.
1.7 Intended usage
The equipment is intended to be used, if a power supply or battery charger, only as a variable voltage and current
source, or, if an electronic load, only as a variable current sink.
Typical application for a power supply is DC supply to any relevant user, for a battery charger the charging of vari-
ous battery types and for electronic loads the replacement of an ohmic resistor by an adjustable DC current sink
in order to load relevant voltage and current sources of any type.
• Claims of any sort due to damage caused by non-intended usage will not be accepted.
• All damage caused by non-intended usage is solely the responsibility of the operator.