Datasheet
Irrtümer und Änderungen vorbehalten / Subject to modication without notice, errors and omissions excepted
© EA-Elektro-Automatik GmbH, 2014
EA-PSI 9000 2U 1000W - 3000W
PROGRAMMIERBARE DC-LABORNETZGERÄTE / PROGRAMMABLE LABORATORY DC POWER SUPPLIES
AC input
All units are provided with an active Power Factor Correction
circuit and models up to 1.5kW are suitable for a worldwide
usage on a mains supply from 90V
AC
up to 264V
AC
. With the
1.5kW models, the output power is automatically reduced to
1kW if the supply voltage is <150V
AC
and with the 3kW models
is reduced to 2.5kW at <205V
AC
.
Power
All models are equipped with a exible auto-ranging
output stage which provides a higher output voltage
at lower output current, or a higher output current
at lower output voltage, always limited to the max.
nominal output power. The maximum power set
value is adjustable with these models. Therefore, a
wide range of applications can already be covered
by the use of just one single unit.
DC output
DC output voltages between 0...40V and 0...750V, output
currents between 0...4A and 0...120A and output powers
between 0...1000W and 0...3000W are available.
Current, voltage and power can thus be adjusted continuously
between 0% and 100%, no matter if manually or remotely
controlled (analog or digital).
The output terminal is located on the rear panel.
Protective features
For protection of the equipment connected, it is possible to
set an overvoltage protection threshold (OVP), as well as one
for overcurrent (OCP) and overpower (OPP).
As soon as one of these thresholds is reached for any rea-
son, the DC output will be immediately shut off and a status
signal will be generated on the display and via the interfaces.
There is furthermore an overtemperature protection, which
will shut off the DC output if the device overheats.
Remote sensing
The standard sensing input can be connected directly to
the load in order to compensate for voltage drops along the
power cables, up to a certain level. Once the sensing input is
connected to the load, the power supply will adjust the output
voltage automatically to ensure the accurate required voltage
is available at the load.
Display and controls
Set values and actual values of output voltage, output current
and output power are clearly represented on the graphic dis-
play. The LC display is touch sensitive and can be intuitively
used to control all functions of the device with just a nger.
Set values of voltage, current, power or resistance (internal
resistance simulation) can be adjusted using the rotary knobs
or entered directly via a numpad.
To prevent unintentional operations, all operation controls
can be locked.
Built-in analog interface
There is a galvanically isolated analog inter-
face terminal, located on the rear of the de-
vice. It offers analog inputs to set voltage, cur-
rent and power from 0...100% through control
voltages of 0V...10V or 0V...5V. To monitor the
output voltage and current, there are analog
outputs with voltage ranges of 0V...10V or
0V...5V. Also, several inputs and outputs are
available for controlling and monitoring the
device status.
AC-Eingang
Die Geräte besitzen alle eine aktive Leistungsfaktorkorrektur
(PFC). Modelle bis 1,5kW sind für den weltweiten Einsatz
an Netzspannungen von 90V
AC
bis 264V
AC
ausgelegt. Bei
den 1,5kW-Geräten wird die Ausgangsleistung bei einer Ein-
gangsspannung <150V
AC
auf 1kW, sowie bei 3kW-Geräten bei
<205V
AC
auf 2,5kW reduziert.
Leistung
Alle Modelle haben eine exible, leistungsgeregelte
Ausgangsstufe, die bei hoher Ausgangsspannung den
Strom oder bei hohem Ausgangsstrom die Spannung
so reduziert, daß die maximale Ausgangsleistung nicht
überschritten wird. Der maximale Leistungswert ist
hierbei einstellbar.
So kann mit nur einem Gerät ein breites Anwendungs-
spektrum abgedeckt werden.
DC-Ausgang
Zur Verfügung stehen Geräte mit einer DC-Ausgangsspannung
zwischen 0...40V und 0...750V, Ströme zwischen 0...4A und
0...120A, sowie Leistungen zwischen 0...1000W und 0...3000W.
Strom, Spannung und Leistung sind somit jeweils zwischen
0% und 100% kontinuierlich einstellbar, egal ob bei manueller
Bedienung oder per Fernsteuerung über analoge oder digitale
Schnittstelle.
Der Ausgang bendet sich auf der Rückseite der Geräte.
Schutzfunktionen
Um die angeschlossenen Verbraucher vor Beschädigung zu
schützen, können eine Überspannungsschwelle (OVP), eine
Überstromschwelle (OCP), sowie eine Überleistungsschwelle
(OPP) eingestellt werden. Bei Erreichen eines dieser Werte wird
der DC-Ausgang abgeschaltet und es wird eine Alarmmeldung
in der Anzeige, sowie auf den Schnittstellen ausgeben. Weiter-
hin gibt es einen Übertemperaturschutz, der den DC-Ausgang
bei Überhitzung abschaltet.
Fernfühlung (Sensing)
Der serienmäßig vorhandene Fernfühlungseingang (Sense)
kann direkt am Verbraucher angeschlossen werden, um Span-
nungsabfall auf den Lastleitungen bis zu einem gewissen Grad
zu kompensieren. Das Gerät erkennt selbständig, wenn die
Senseleitungen angeschlossen sind und regelt die Ausgangs-
spannung direkt am Verbraucher.
Anzeige- und Bedienelemente
Istwerte und Sollwerte von Ausgangsspannung, -strom und
-leistung werden auf einem Grakdisplay übersichtlich darge-
stellt. Die LCD-Anzeige ist berührungssensitiv und ermöglicht
intuitive Bedienung aller Funktionen des Gerätes.
Mittels Drehknöpfen oder auch per Direkteingabe über eine
Zehnertastatur können Spannung, Strom, Leistung und der
Innenwiderstand eingestellt werden. Sie dienen außerdem dazu
Einstellungen im Menü vornehmen zu können.
Zum Schutz gegen Fehlbedienung können die Bedienelemente
gesperrt werden.
Eingebaute Analogschnittstelle
Eine galvanisch getrennte Analogschnittstelle
bendet sich auf der Rückseite des Gerätes.
Sie verfügt über analoge Steuereingänge mit
0...10V oder 0...5V um Spannung, Strom und
Leistung von 0...100% zu programmieren.
Ausgangsspannung und Ausgangsstrom kön-
nen über analoge Monitorausgänge mit 0...10V
oder 0...5V ausgelesen werden. Weiterhin gibt
es Statuseingänge und -ausgänge.