Elektro-Automatik GmbH Betriebsanleitung PSI 9000 2U DC-Labornetzgerät Doc ID: PSI92UDE Revision: 02 Date: 04/2014
PSI 9000 2U Serie INHALT 1 ALLGEMEINES 1.1 1.1.1 1.1.2 1.1.3 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.8.1 1.8.2 1.8.3 1.8.4 1.8.5 1.9 1.9.1 1.9.2 1.9.3 1.9.4 1.10 1.10.1 1.10.2 1.10.3 1.10.4 1.10.5 1.10.6 1.10.7 1.10.8 1.10.9 1.10.10 1.10.11 1.10.12 2 Zu diesem Dokument.....................................5 Aufbewahrung und Verwendung....................5 Urheberschutz (Copyright).............................5 Geltungsbereich..............................................5 Symbolerläuterungen......................
PSI 9000 2U Serie 3.8.15 3.9 3.9.1 3.9.2 3.9.3 Fernsteuerung des Funktionsgenerators.....77 Weitere Anwendungen.................................78 Parallelschaltung in Master-Slave (MS).......78 Reihenschaltung...........................................81 Zwei-Quadranten-Betrieb (2QB)..................82 4 INSTANDHALTUNG & WARTUNG 5 ZUBEHÖR UND OPTIONEN 6 SERVICE & SUPPORT 4.1 4.2 4.2.1 4.3 4.3.1 4.3.2 4.4 4.4.1 4.4.2 4.4.3 5.1 Wartung / Reinigung.....................................
PSI 9000 2U Serie 1. Allgemeines 1.1 Zu diesem Dokument 1.1.1 Aufbewahrung und Verwendung Dieses Dokument ist für den späteren Gebrauch und stets in der Nähe des Gerätes aufzubewahren und dient zur Erläuterung des Gebrauchs des Gerätes. Bei Standortveränderung und/oder Benutzerwechsel ist dieses Dokument mitzuliefern und bestimmungsgemäß anzubringen bzw. zu lagern. 1.1.
PSI 9000 2U Serie 1.5 Entsorgung des Gerätes 1.6 Produktschlüssel Ein Gerät, das zur Entsorgung vorgesehen ist, muß laut europaweit geltenden Gesetzen und Verordnungen (ElektroG, WEEE) vom Hersteller zurückgenommen und entsorgt werden, sofern der Betreiber des Gerätes oder ein von ihm Beauftragter das nicht selbst erledigt.
PSI 9000 2U Serie 1.8 Sicherheit 1.8.1 Sicherheitshinweise Lebensgefahr - Gefährliche Spannung • Beim Betrieb elektrischer Geräte stehen zwangsweise bestimmte Teile unter teils gefährlicher Spannung, mit Ausnahme der 40 V-Modelle gemäß SELV.
PSI 9000 2U Serie 1.8.3 Pflichten des Betreibers Betreiber ist jede natürliche oder juristische Person, die das Gerät nutzt oder Dritten zur Anwendung überläßt und während der Nutzung für die Sicherheit des Benutzers, des Personals oder Dritter verantwortlich ist. Das Gerät wird im gewerblichen Bereich eingesetzt. Der Betreiber des Gerätes unterliegt daher den gesetzlichen Pflichten zur Arbeitssicherheit.
PSI 9000 2U Serie 1.8.5 Alarmsignale Das Gerät bietet diverse Möglichkeiten der Signalisierung von Alarmsituationen, jedoch nicht von Gefahrensituationen. Die Signalisierung kann optisch (auf der Anzeige als Text), akustisch (Piezosummer) oder elektronisch (Pin/Meldeausgang an einer analogen Schnittstelle) erfolgen. Alle diese Alarme bewirken die Abschaltung des DC-Ausgangs.
PSI 9000 2U Serie 1.9.3 Spezifische technische Daten Modell 2U 1000 W PSI 9040-40 PSI 9080-40 PSI 9200-15 Netzspannung 90...264 V AC 90...264 V AC 90...264 V AC Netzanschluß 1ph,N,PE 1ph,N,PE 1ph,N,PE Netzfrequenz 50/60 Hz 50/60 Hz 50/60 Hz Netzsicherung (intern) T16 A T16 A T16 A Ableitstrom < 3.5 mA < 3.5 mA < 3.5 mA Leistungsfaktor ~ 0.99 ~ 0.99 ~ 0.
PSI 9000 2U Serie Modell 2U 1000 W PSI 9040-40 PSI 9080-40 PSI 9200-15 Einstellbereich 0...30 Ω 0...60 Ω 0...400 Ω Genauigkeit ≤ 2% vom Widerstandsbereich ± 0,3% vom Strombereich Innenwiderstandsregelung (1 Anzeige: Einstellauflösung Siehe Abschnitt „1.10.6.4. Auflösung der Anzeigewerte“ Anzeige: Genauigkeit ≤ 0,4% (2 Analoge Schnittstelle (3 Steuereingänge U, I, P U, I, P U, I, P Monitorausgänge Meldesignale U, I DC ein/aus, Fernst. ein/aus CV, OVP, OT U, I DC ein/aus, Fernst.
PSI 9000 2U Serie Modell 2U 1000 W PSI 9360-10 PSI 9500-06 PSI 9750-04 Netzspannung 90...264 V AC 90...264 V AC 90...264 V AC Netzanschluß 1ph,N,PE 1ph,N,PE 1ph,N,PE Netzfrequenz 50/60 Hz 50/60 Hz 50/60 Hz Netzsicherung (intern) T16 A T16 A T16 A Ableitstrom < 3.5 mA < 3.5 mA < 3.5 mA Leistungsfaktor ~ 0.99 ~ 0.99 ~ 0.99 Maximale Spannung UNenn 360 V 500 V 750 V Maximaler Strom INenn 10 A 6A 4A Maximale Leistung PNenn 1000 W 1000 W 1000 W Einstellbereich 0...
PSI 9000 2U Serie Modell 2U 1000 W PSI 9360-10 PSI 9500-06 PSI 9750-04 Einstellbereich 0...1080 Ω 0...2500 Ω 0...5625 Ω Genauigkeit ≤ 2% vom Widerstandsbereich ± 0,3% vom Strombereich Innenwiderstandsregelung (1 Anzeige: Einstellauflösung Siehe Abschnitt „1.10.6.4. Auflösung der Anzeigewerte“ Anzeige: Genauigkeit ≤ 0,4% (2 Analoge Schnittstelle (3 Steuereingänge U, I, P U, I, P U, I, P Monitorausgänge Meldesignale U, I DC ein/aus, Fernst. ein/aus CV, OVP, OT U, I DC ein/aus, Fernst.
PSI 9000 2U Serie Modell 2U 1500 W PSI 9040-60 PSI 9080-60 PSI 9200-25 Netzspannung 90...264 V AC 90...264 V AC 90...264 V AC - mit zusätzlichem Derating 90...150 V AC 90...150 V AC 90...
PSI 9000 2U Serie Modell 2U 1500 W PSI 9040-60 PSI 9080-60 PSI 9200-25 Einstellbereich 0...20 Ω 0...40 Ω 0...240 Ω Genauigkeit ≤ 2% vom Widerstandsbereich ± 0,3% vom Strombereich Innenwiderstandsregelung (1 Anzeige: Einstellauflösung Siehe Abschnitt „1.10.6.4. Auflösung der Anzeigewerte“ Anzeige: Genauigkeit ≤ 0,4% (2 Analoge Schnittstelle (3 Steuereingänge U, I, P U, I, P U, I, P Monitorausgänge Meldesignale U, I DC ein/aus, Fernst. ein/aus CV, OVP, OT U, I DC ein/aus, Fernst.
PSI 9000 2U Serie Modell 2U 1500 W PSI 9360-15 PSI 9500-10 PSI 9750-06 Netzspannung 90...264 V AC 90...264 V AC 90...264 V AC - mit zusätzlichem Derating 90...150 V AC 90...150 V AC 90...
PSI 9000 2U Serie Modell 2U 1500 W PSI 9360-15 PSI 9500-10 PSI 9750-06 Einstellbereich 0...720 Ω 0...1500 Ω 0...3750 Ω Genauigkeit ≤ 2% vom Widerstandsbereich ± 0,3% vom Strombereich Innenwiderstandsregelung (1 Anzeige: Einstellauflösung Siehe Abschnitt „1.10.6.4. Auflösung der Anzeigewerte“ Anzeige: Genauigkeit ≤ 0,4% (2 Analoge Schnittstelle (3 Steuereingänge U, I, P U, I, P U, I, P Monitorausgänge Meldesignale U, I DC ein/aus, Fernst. ein/aus CV, OVP, OT U, I DC ein/aus, Fernst.
PSI 9000 2U Serie Modell 2U 3000 W PSI 9040-120 PSI 9080-120 PSI 9200-50 Netzspannung 180...264 V AC 180...264 V AC 180...264 V AC - mit zusätzlichem Derating 180...207 V AC 180...207 V AC 180...
PSI 9000 2U Serie Modell 2U 3000 W PSI 9040-120 PSI 9080-120 PSI 9200-50 Einstellbereich 0...10 Ω 0...20 Ω 0...120 Ω Genauigkeit ≤ 2% vom Widerstandsbereich ± 0,3% vom Strombereich Innenwiderstandsregelung (1 Anzeige: Einstellauflösung Siehe Abschnitt „1.10.6.4. Auflösung der Anzeigewerte“ Anzeige: Genauigkeit ≤ 0,4% ≤ 0,4% ≤ 0,4% Steuereingänge U, I, P U, I, P U, I, P Monitorausgänge Meldesignale U, I DC ein/aus, Fernst. ein/aus CV, OVP, OT U, I DC ein/aus, Fernst.
PSI 9000 2U Serie Modell 2U 3000 W PSI 9360-30 PSI 9500-20 PSI 9750-12 Netzspannung 180...264 V AC 180...264 V AC 180...264 V AC - mit zusätzlichem Derating 180...207 V AC 180...207 V AC 180...
PSI 9000 2U Serie Modell 2U 3000 W PSI 9360-30 PSI 9500-20 PSI 9750-12 Einstellbereich 0...360 Ω 0...750 Ω 0...1875 Ω Genauigkeit ≤ 2% vom Widerstandsbereich ± 0,3% vom Strombereich Innenwiderstandsregelung (1 Anzeige: Einstellauflösung Siehe Abschnitt „1.10.6.4. Auflösung der Anzeigewerte“ Anzeige: Genauigkeit ≤ 0,4% ≤ 0,4% ≤ 0,4% Steuereingänge U, I, P U, I, P U, I, P Monitorausgänge Meldesignale U, I DC ein/aus, Fernst. ein/aus CV, OVP, OT U, I DC ein/aus, Fernst.
PSI 9000 2U Serie Ansichten A - Netzschalter B - Bedienteil C - Steuerungsschnittstellen (digital, analog) D - Lüftungsaustritte E - Share-Bus- und Fernfühlungsanschlüsse F - DC-Ausgang (Klemme Typ 1) G - Netzsicherung H - Netzanschluß 1.9.4 Bild 1 - Vorderseite Seite 22 Bild 2 - Rückseite EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Telefon: 02162 / 3785-0 Telefax: 02162 / 16230 www.elektroautomatik.de ea1974@elektroautomatik.
Bild 3 - Seitenansicht von links, mit DC-Klemme Typ 1 Bild 4 - Seitenansicht von rechts, mit DC-Klemme Typ 2 PSI 9000 2U Serie EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Telefon: 02162 / 3785-0 Telefax: 02162 / 16230 www.elektroautomatik.de ea1974@elektroautomatik.
PSI 9000 2U Serie Bild 5 - Ansicht von oben, mit DC-Abdeckung (Klemme Typ 1) Seite 24 EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Telefon: 02162 / 3785-0 Telefax: 02162 / 16230 www.elektroautomatik.de ea1974@elektroautomatik.
PSI 9000 2U Serie Bild 6 - Bedienfeld Übersicht der Bedienelemente am Bedienfeld Für eine genaue Erläuterung siehe Abschnitte „1.10.6. Die Bedieneinheit (HMI)“ und „1.10.6.2. Tasten“. Anzeige mit berührungsempfindlicher Oberfläche (Touchscreen, resistiv) (1) Dient zur Auswahl von Sollwerten, Menüs, Zuständen, sowie zur Anzeige der Istwerte und des Status. Der Touchscreen kann mit den Fingern oder mit einem Stift (Stylus) bedient werden.
PSI 9000 2U Serie 1.10 Aufbau und Funktion 1.10.1 Allgemeine Beschreibung Die elektronischen Hochleistungsnetzgeräte der Serie PSI 9000 2U sind durch ihre recht kompakten 19“-Einschubgehäuse mit 2 Höheneinheiten (2U) besonders für Prüfsysteme und Industriesteuerungen geeignet. Über die gängigen Funktionen von Stromversorgungen hinaus können mit dem integrierten Funktionsgenerator sinus-, rechteck- oder dreieckförmige Sollwertkurven sowie weitere Kurvenformen erzeugt werden.
PSI 9000 2U Serie 1.10.3 Lieferumfang 1 x Netzgerät PSI 9000 2U 1 x Netzkabel 2 m 1 x Gedruckte Betriebsanleitung 1 x Stecker für Share-Bus (separat oder aufgesteckt) 1 x Stecker für Fernfühlung (separat oder aufgesteckt) 1 x USB-Kabel 1,8 m 1 x Set Abdeckbleche (für Umrüstung auf 19“ <-> Tisch) 1 x CD „Drivers & Tools“ 1.10.
PSI 9000 2U Serie 1.10.6 Die Bedieneinheit (HMI) HMI steht für Human Machine Interface, aut deutsch Mensch-Maschine-Schnittstelle und besteht hier aus einer Anzeige mit berührungsempfindlicher Oberfläche (Touchscreen), zwei Drehknöpfen, einem Taster und einem USB-Port Typ A. 1.10.6.1 Anzeige mit Touchscreen Die grafische Anzeige mit Touchscreen ist in mehrere Bereiche aufgeteilt.
PSI 9000 2U Serie • Statusanzeigen (oben rechts) Dieses Feld zeigt diverse Statustexte und -symbole an: Anzeige Beschreibung Gesperrt Das HMI ist gesperrt Entsperrt Das HMI ist nicht gesperrt Ausgang EIN Der DC-Ausgang ist eingeschaltet Ausgang AUS Der DC-Ausgang ist ausgeschaltet Fern Das Gerät befindet sich in Fernsteuerung durch... Analog ...die eingebaute Analogschnittstelle USB & andere ...
PSI 9000 2U Serie 1.10.6.3 Drehknöpfe Solange das Gerät manuell bedient wird, dienen die beiden Drehknöpfe zur Einstellung aller Sollwerte, sowie zur Auswahl und Einstellung der Parameter in den Seiten SETTINGS und MENU. Für eine genauere Erläuterung der einzelnen Funktionen siehe „3.3 Manuelle Bedienung“ auf Seite 44. Beide Drehköpfe haben noch eine zusätzliche Tastfunktion, die mit jedem Druck die gewählte Dezimalstelle des einzustellenden Wertes verschiebt. So kann z. B.
PSI 9000 2U Serie iu.csv IU-Tabelle für den IU-Funktionsgenerator. Werte werden als Stromwerte zwischen 0 A und 125% INenn (siehe techn. Daten) interpretiert. Ist irgendein Wert zu hoch, wird das Laden abgebrochen und eine Fehlermeldung ausgegeben. Der Name muß am Anfang iu enthalten, der Rest ist beliebig. ui.csv UI-Tabelle für den UI-Funktionsgenerator. Werte werden als Spannungswerte zwischen 0 V und 125% UNenn (siehe techn. Daten) interpretiert.
PSI 9000 2U Serie 1.10.9 Analogschnittstelle Diese 15polige Sub-D-Buchse auf der Rückseite dient zur Fernsteuerung des Gerätes mittels analogen Signalen bzw. Schaltzuständen. Wenn ferngesteuert werden soll, kann diese analoge Schnittstelle nur alternativ zu einer der digitalen benutzt werden. Überwachung (Monitoring) ist jedoch jederzeit möglich. Der Eingangsspannungsbereich der Sollwerte bzw.
PSI 9000 2U Serie 2. Installation & Inbetriebnahme 2.1 Transport und Lagerung 2.1.1 Transport • Die Griffe an der Vorderseite des Gerätes dienen nicht zum Tragen! • Das Gerät sollte aufgrund seines, je nach Modell, hohen Gewichts möglichst nicht per Hand transportiert werden bzw.
PSI 9000 2U Serie 2.3.2 Vorbereitung Für den netzseitigen Anschluß des Netzgerätes der Serie PSI 9000 2U ist ein 3poliges Netzkabel von 2 m Länge im Lieferumfang enthalten. Soll das Gerät anders verkabelt werden, so ist sicherzustellen, daß der Querschnitt der verwendeten Zuleitung mindestens 3x 2,5 mm² (wie beim Netzkabel) beträgt.
PSI 9000 2U Serie 2.3.4 Anschluß an das Stromnetz (AC) • Der Anschluß des Gerätes mittels des mitgelieferten Netzkabels kann an jeder Wandsteckdose bzw. Steckdosenverteilung erfolgen, die über einen Schutzkontakt verfügt und für mindestens 16 A ausgelegt ist.
PSI 9000 2U Serie 2.3.5.2 Kabelzuführung und Plastikabdeckung Für die DC-Anschlußklemme wird eine Plastikabdeckung (siehe oben) als Berührungsschutz mitgeliefert. Diese sollte immer installiert sein. Beide Abdeckungen werden mit Rändelmuttern an der Anschlußklemme fixiert. Im Gegensatz zum Typ 2 sind in der Abdeckung Typ 1 Ausbrüche (oben, unten) vorhanden, die nach Bedarf ausgebrochen werden können, um Zuleitungen aus verschiedenen Richtungen zu verlegen.
PSI 9000 2U Serie 2.3.7 Anschluß der Fernfühlung Um Spannungsabfälle auf den DC-Zuleitungen bis zu einem gewissen Grad kompensieren zu können, bietet das Gerät einen Fernfühlungsanschluß („Sense“, Rückseite), der mit der Last verbunden werden kann. Das Gerät erkennt den Fernfühlungsbetrieb automatisch und regelt die Ausgangsspannung (nur im CV-Betrieb möglich) dann an der Last, statt am eigenen DC-Ausgang. In den technischen Daten (siehe „1.9.
PSI 9000 2U Serie 2.3.8 Installation eines AnyBus-Schnittstellenmoduls Die diversen Schnittstellenmodule, die für das Gerät verfügbar sind, können durch den Anwender nachgerüstet werden und sind durch andere Module austauschbar. Die Einstellungen zum momentan installierten Modul variieren und sollte nach der Erstinstallation bzw. nach Wechsel des Modultyps überprüft und ggf. neu eingestellt werden.
PSI 9000 2U Serie 2.3.10 Anschließen des „Share-Bus“ Die rückseitig am Gerät befindliche Klemme „Share-Bus“ dient entweder zur Verbindung mit dem Share-Bus einer kompatiblen elektronischen Last (z. B. ELR 9000), um Zwei-Quadranten-Betrieb zu fahren, oder bei Parallelbetrieb mehrerer Netzgeräte zur Spannungs- und dadurch auch Stromsymmetrierung und Ausregelung. Der Share-Bus sollte daher verbunden werden. Weitere Information siehe auch „3.9.3 Zwei-Quadranten-Betrieb (2QB)“ auf Seite 82.
PSI 9000 2U Serie 2.3.12 Erstinbetriebnahme Bei der allerersten Inbetriebnahme nach dem Erwerb des Gerätes und der Erstinstallation sind zusätzliche Maßnahmen zu ergreifen: • Überprüfen Sie die von Ihnen verwendeten Anschlußkabel für AC und DC auf ausreichenden Querschnitt! • Überprüfen Sie die werkseitigen Einstellungen bezüglich Sollwerte, Sicherheits- und Überwachungsfunktionen sowie Kommunikation daraufhin, daß Sie für Ihre Anwendung passen und stellen Sie sie ggf.
PSI 9000 2U Serie 3. Bedienung und Verwendung 3.
PSI 9000 2U Serie 3.2.3 Leistungsregelung / Konstantleistung / Leistungsbegrenzung Leistungsregelung, auch Leistungsbegrenzung oder Konstantleistung (kurz: CP) genannt, hält die DC-Ausgangsleistung bei Netzgeräten konstant auf dem eingestellten Wert, wenn der in den Verbraucher fließende Strom in Zusammenhang mit der eingestellten Ausgangsspannung und dem Widerstand des Verbrauchers nach P = U * I bzw. P = U² / R die Maximalleistung erreicht.
PSI 9000 2U Serie 3.2.5 Alarmzustände Dieser Abschnitt gibt nur eine Übersicht über mögliche Alarmzustände. Was zu tun im Fall, daß Ihr Gerät Ihnen einen Alarm anzeigt, wird in Abschnitt „3.5. Alarme und Überwachung“ erläutert. Grundsätzlich werden alle Alarmzustände optisch (Text + Meldung in der Anzeige), akustisch (wenn Alarmton aktiviert) und als auslesbarer Status über digitale Schnittstelle signalisiert. Außerdem wird bei einem Alarm der DC-Ausgang des Gerätes ausgeschaltet.
PSI 9000 2U Serie 3.3 Manuelle Bedienung 3.3.1 Einschalten des Gerätes Das Gerät sollte möglichst immer am Netzschalter (Vorderseite) eingeschaltet werden. Alternativ kann es über eine externe Trennvorrichtung (Hauptschalter, Schütz) mit entsprechender Strombelastbarkeit netzseitig geschaltet werden.
MENU Einst. Spannungsregler: Langsam | Schnell R-Modus aktivieren: Ja | Nein Seite 4 Seite 5 Seite 6 Nutzer-Profil 2 Nutzer-Profil 3 Nutzer-Profil 4 Nutzer-Profil 5 Info HW, SW... EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Telefon: 02162 / 3785-0 Telefax: 02162 / 16230 www.elektroautomatik.de ea1974@elektroautomatik.de OPD = {0W...Pnenn} Aktion = {KEINE | SIGNAL | WARNUNG |ALARM} OCD = {0A...Inenn} Aktion = {KEINE | SIGNAL | WARNUNG |ALARM} UCD = {0A...
MENU Seite 46 EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Telefon: 02162 / 3785-0 Telefax: 02162 / 16230 UI-IU Arbiträr Rampe DIN 40839 Trapez U U(Off) = U(A)…Umax-U(A) I Von USB laden t2= 0.1ms...36000s (1ms) Ue(DC)= 0V...Umax Uend= 0V...Umax I t1= 0.1ms...36000s (1ms) Ustart= 0V...Umax U t4= 0.1ms...36000s (1ms) t3= 0.1ms...36000s (1ms) t2= 0.1ms...36000s (1ms) t1= 0.1ms...36000s (1ms) U(A)= 0V...Umax-Offset t2= 0.1ms...36000s (1ms) t1= 0.1ms...
MENU HMI Einstellung Kommunikation EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Immer an Helligkeit: 1...10 Alles sperren Ton ein Ton ein Hinterg.Beleuchtung Display Kontrast HMI Sperre Tastenton Alarmton Telefon: 02162 / 3785-0 Telefax: 02162 / 16230 TP Kalibrierung HMI Update English (Schnittstellentyp) Ethernet Sprache Schnittstellenmodul konfigurieren Ton aus Ton aus EIN/AUS möglich 60 Sekunden an Weitere... Deutsch ... PSI 9000 2U Serie www.elektroautomatik.
PSI 9000 2U Serie 3.3.3.1 Menü „Allgemeine Einstellungen“ Element Fernsteuerung erlauben Share-Bus-Modus Ausgang nach Power ON S. Beschreibung 1 Bei Wahl „Nein“ kann das Gerät weder über eine der digitalen, noch über die analoge Schnittstelle fernbedient werden. Der Status, daß die Fernsteuerung gesperrt ist, wird im Statusfeld der Hauptseite mit „Lokal“ angezeigt. Siehe auch Abschnitt 1.10.6.1. 1 Für Parallelschaltung mehrerer Geräte über Share-Bus oder Zwei-QuadrantenBetrieb (siehe „3.9.3.
PSI 9000 2U Serie 3.3.3.5 Menü „Info HW, SW...“ Diese Menüseite zeigt eine Übersicht gerätebezogener Daten wie Serienummer, Artikelnummer usw. an. 3.3.3.6 Menü „Funkt.Generator“ Siehe „3.8 Der Funktionsgenerator“ auf Seite 63. 3.3.3.7 Menü „Kommunikation“ Hier werden Einstellungen zur digitalen Kommunikation über die diversen, optional erhältlichen Schnittstellenmodule (Interfaces, kurz: IF) der IF-AB-Serie getroffen.
PSI 9000 2U Serie Profinet/IO, 1 & 2 Port IF Ebene 1 Ebene 2 IP Einstellungen DHCP Hostname Domäne SMTPEinstellungen Funktionsbeschreib. Standortbeschreib. Stationsname Beschreib. Datum der Installation Ebene 3 Beschreibung Das IF läßt sich von einem DHCP-Server eine IP und ggf. eine Subnetzmaske, sowie Gateway zuweisen. Falls kein DHCP-Server im Netzwerk ist, werden die Netzwerkparameter gesetzt, die im Punkt „Manuell“ definiert worden. Manuell IP Diese Option ist standardmäßig aktiviert.
PSI 9000 2U Serie 3.3.3.8 Menü „HMI-Einstellung“ Diese Einstellungen beziehen sich ausschließlich auf die Bedieneinheit (HMI). Element Sprache Beschreibung Umschaltung der Sprache in der Anzeige. Mit Stand 14.04.2014 sind verfügbar: Deutsch, Englisch Weitere Sprachen (maximal 3 können integriert sein) können auf Anfrage erstellt und durch ein Update des HMI aufgespielt werden. Standardmäßig wären dann Englisch, plus zwei weitere Sprachen wie Italienisch, Französisch oder Spanisch usw. machbar. Hinterg.
PSI 9000 2U Serie Die Einstellgrenzen sind an die Sollwerte gekoppelt. Das bedeutet, daß die obere Einstellgrenze (-max) des Sollwertes nicht kleiner bzw. die untere Einstellgrenze (-min) nicht höher eingestellt werden kann als der Sollwert momentan ist. Beispiel: Wenn man die Einstellgrenze der Leistung (P-max) auf 1.00 kW einstellen möchte und der Leistungssollwert ist noch auf 2.00 kW eingestellt, dann müßte man den Leistungssollwert zuerst auf 1.00 kW oder geringer einstellen. 3.3.
PSI 9000 2U Serie ►►So können Sie manuell Sollwerte U, I, oder P mit den Drehknöpfen einstellen 1. Prüfen Sie zunächst, ob der Sollwert (U, I, P), den Sie einstellen wollen, bereits einem der Drehknöpfe zugeordnet ist. Die Hauptseite zeigt die Zuordnung rechts an mit einem Bedienfeld: 2.
PSI 9000 2U Serie 3.3.7 DC-Ausgang ein- oder ausschalten Der DC-Ausgang des Gerätes kann manuell oder ferngesteuert aus- oder eingeschaltet werden. Bei manueller Bedienung kann dies jedoch durch die Bedienfeldsperre verhindert sein. ►►So schalten Sie den DC-Ausgang manuell ein oder aus 1. Sofern das Bedienfeld nicht komplett gesperrt ist, betätigen Sie Taste On/Off. Anderenfalls werden Sie 2. zunächst gefragt, die Sperre aufzuheben.
PSI 9000 2U Serie 3.4.3 Fernsteuerung über eine digitale Schnittstelle 3.4.3.1 Schnittstellenwahl Das Gerät unterstützt zusätzlich zur serienmäßig eingebauten USB-Schnittstelle folgende optional erhältliche Schnittstellenmodule, unter denen der Anwender wählen kann: Kurzbezeichnung IF-AB-CANO IF-AB-RS232 IF-AB-PBUS IF-AB-ETH1P IF-AB-PNET1P IF-AB-DNET IF-AB-MBUS IF-AB-ETH2P IF-AB-MBUS2P IF-AB-PNET2P Art.nr.
PSI 9000 2U Serie 3.4.4 Fernsteuerung über Analogschnittstelle (AS) 3.4.4.
PSI 9000 2U Serie 3.4.4.3 Spezifikation der Analogschnittstelle Pin Name Typ* Bezeichnung Pegel 0…10 V bzw. 0...5 V entsprechen 0..100% von UNenn 0…10 V bzw. 0...5 V entsprechen 0..100% von INenn 1 VSEL AI Sollwert Spannung 2 CSEL AI Sollwert Strom 3 VREF AO Referenzspannung 4 DGND POT Bezugspotential für alle digitalen Signale Elektrische Eigenschaften Genauigkeit < 0,2% Eingangsimpedanz Ri >40 kΩ...
PSI 9000 2U Serie 3.4.4.5 Anwendungsbeispiele a) Ausgang ausschalten über Pin „Rem-SB“ Der Pin „REM-SB“ kann bei Fernsteuerung zum Ein- und Ausschalten des Ausganges genutzt werden. Es wird empfohlen, einen niederohmigen Kontakt wie einen Schalter, ein Relais oder Transistor zum Schalten des Pins gegen Masse (DGND) zu benutzen. Ein digitaler Ausgang, z. B. von einer SPS, kann diesen Eingang unter Umständen nicht sauber ansteuern, da eventuell nicht niederohmig genug.
PSI 9000 2U Serie 3.5 Alarme und Überwachung 3.5.1 Begriffsdefinition Grundsätzlich wird unterschieden zwischen Gerätealarmen (siehe „3.2.5. Alarmzustände“) wie Überspannung oder Übertemperatur und benutzerdefinierten Ereignissen, wie z. B. OVD (Überspannungsüberwachung).
PSI 9000 2U Serie Diese Gerätealarme können nicht konfiguriert werden, da hardwaremäßig bedingt: Alarm Bedeutung Beschreibung Netzunter- oder überspannung. Löst einen Alarm aus, wenn die ACVersorgung außerhalb der Spezifikationen des Gerätes arbeiten sollte (Spannung/Frequenz) oder wenn das Gerät von der AC-Versorgung getrennt wird, z. B. durch Ausschalten am Netzdrehschalter. Außerdem wird der DC-Ausgang ausgeschaltet.
PSI 9000 2U Serie ►►So konfigurieren Sie die Events 1. Tippen Sie in der Hauptseite auf das Bedienfeld . 2. Tippen Sie auf der rechten Seite auf die weißen dreieckigen Pfeile 3. , um „4.1 Event U“ oder „4.2 Event I“ oder „4.3 Event P“ auszuwählen. Stellen Sie hier mit dem linken Drehknopf die Überwachungsgrenze sowie mit dem rechten Drehknopf die von dem Event auszulösende Aktion (siehe „3.5.1. Begriffsdefinition“) gemäß der Anwendung ein. 4. Übernehmen Sie die Einstellungen mit .
PSI 9000 2U Serie 3.7 Nutzerprofile laden und speichern Das Menü „Profile“ dient zur Auswahl eines Profils zum Laden bzw. zum Wechsel zwischen einem Standardprofil und 5 Nutzerprofilen. Ein Profil ist eine Sammlung aller Einstellungen und aller Sollwerte. Bei Auslieferung des Gerätes bzw. nach einem Zurücksetzungsvorgangs haben alle sechs Profile dieselben Einstellungen und sämtliche Sollwerte sind auf 0.
PSI 9000 2U Serie 3.8 Der Funktionsgenerator 3.8.1 Einleitung Der eingebaute Funktionsgenerator ist, wie bei den gleichnamigen Geräten, in der Lage, verschiedenförmige Signalformen zu erzeugen und diese auf jeweils einen der Sollwerte Spannung (U) oder Strom (I) anzuwenden. Bei aktiviertem Widerstandsmodus (R-Modus) ist der Zugang zum Funktionsgenerator gesperrt. Die Funktionen des Generators können am Gerät manuell komplett bedient werden.
PSI 9000 2U Serie 3.8.3 Arbeitsweise Zum Verständnis, wie der Funktionsgenerator arbeitet und wie die eingestellten Werte aufeinander einwirken, muß folgendes beachtet werden: Das Gerät arbeitet auch im Funktionsgeneratormodus stets mit den drei Sollwerten U, I und P. Auf einen der beiden Sollwerte U und I kann die gewählte Funktion angewendet werden, die anderen beiden Sollwerte sind dann konstant und wirken begrenzend.
PSI 9000 2U Serie Nachdem die Einstellungen getroffen wurden, muß die Funktion geladen werden. ►►So laden Sie eine Funktion: 1. Nachdem Sie die Werte für das zu generierende Signal eingestellt haben, tippen Sie auf . Das Gerät lädt daraufhin die Daten in die internen Regelung und wechselt die Anzeige. Kurz danach werden die statischen Werte gesetzt (Leistung bzw. Strom oder Spannung), der DC-Ausgang eingeschaltet und das Bedienfeld freigegeben. Erst danach kann die Funktion gestartet werden.
PSI 9000 2U Serie 3.8.6 Dreieck-Funktion Folgende Parameter können für die Dreieck-Funktion konfiguriert werden: Wert Einstellbereich Erläuterung I(A), U(A) 0...(Nennwert - (Off)) von U, I A = Amplitude des zu generierenden Signals I(Off), U(Off) 0...(Nennwert - (A)) von U, I Off = Offset, bezogen auf den Fußpunkt des Dreiecks t1 0,1 ms...36000 s Anstiegszeit der ansteigenden Flanke des Dreiecksignals t2 0,1 ms...
PSI 9000 2U Serie 3.8.8 Trapez-Funktion Folgende Parameter können für die Trapez-Funktion konfiguriert werden: Wert Einstellbereich Erläuterung I(A), U(A) 0...(Nennwert - (Off)) von U, I A = Amplitude des zu generierenden Signals I(Off), U(Off) 0...(Nennwert - (A)) von U, I Off = Offset, bezogen auf den Fußpunkt des Trapezes t1 0,1 ms...36000 s Zeit der ansteigenden Flanke des Trapezsignals t2 0,1 ms...36000 s Zeit des High-Wertes (Haltezeit) des Trapezsignals t3 0,1 ms...
PSI 9000 2U Serie 3.8.10 Arbiträr-Funktion Die Arbiträr-Funktion (arbiträr = beliebig) bietet dem Anwender einen erweiterten Spielraum. Es sind je 100 Sequenzen für die Zuordnung zum Strom I und der Spannung U verfügbar, die alle mit den gleichen Parametern versehen sind, aber durch die Werte unterschiedlich konfiguriert werden können, um so komplexe Funktionsabläufe „zusammenzubauen“. Von den 100 verfügbaren Sequenzen können beliebig viele nacheinander ablaufen. Das ergibt einen Sequenzblock.
PSI 9000 2U Serie Bildliche Darstellungen: Anwendungen und Resultate: Beispiel 2 Betrachtung 1 Ablaufs 1 Sequenz aus 100: Start (DC) Ende (DC) St ar t( En d e AC ) (A C ) A t Seq.Zeit A Die DC-Werte von Start und Ende sind gleich, die AC-Werte (Amplitude) jedoch nicht. Der Endwert ist größer als der Startwert, daher wird die Amplitude mit jeder neu angefangenen Sinushalbwelle kontinuierlich zwischen Anfang und Ende der Sequenz größer.
PSI 9000 2U Serie Durch Aneinanderreihung mehrerer unterschiedlich konfigurierter Sequenzen können komplexe Abläufe erzeugt werden. Dabei kann durch geschickte Konfiguration der Arbiträrgenerator die anderen Funktionen wie Dreieck, Sinus, Rechteck oder Trapez nachbilden und somit z. B. eine Sequenz aus Rechteck-Funktionen mit unterschiedlichen Amplituden bzw. Duty Cycles pro Sequenz erzeugen.
PSI 9000 2U Serie 3.8.10.1 Laden und Speichern von Arbiträr-Funktionen Die manuell am Gerät konfigurierbaren 100 Sequenzen der Arbiträrfunktion, die auf Spannung U oder Strom I anwendbar ist, können über die USB-Schnittstelle auf der Vorderseite des Gerätes auf einen USB-Stick (FAT32formatiert) gespeichert oder von diesem geladen werden. Dabei gilt, daß beim Speichern immer alle 100 Sequenzen in eine Textdatei vom Typ CSV gespeichert werden, beim Laden umgekehrt genauso.
PSI 9000 2U Serie ►►So speichern Sie die 100 Sequenzen vom Gerät auf einen USB-Stick: 1. Stecken Sie den USB-Stick noch nicht ein bzw. ziehen Sie ihn zunächst heraus. 2. Öffnen Sie das Funktionsauswahlmenü des Funktionsgenerators über MENU -> Funkt.Generator -> Arbiträr -> U / I 3. Tippen Sie auf , dann . Das Gerät sucht daraufhin nach dem Ordner HMI_FILES auf dem Speicherstick und nach eventuell schon vorhandenen WAVE_U- bzw. WAVE_I-Dateien und listet gefundene auf.
PSI 9000 2U Serie Bei der IU-Funktion ist die Zuordnung von Meßwert zum aus der Tabelle entnommenen Wert genau andersherum als bei der UI-Funktion, das Verhalten jedoch das gleiche. Man könnte somit das Verhalten der Last bzw. die Strom- und Leistungsaufnahme in Abhängigkeit von der Ausgangsspannung steuern und Lastsprünge erzeugen. Diese Funktion eignet sich sehr gut zur Simulation von Solarpaneelen (Photovoltaik, PV). Beim Laden einer Tabelle von USB-Stick werden nur Textdateien vom Typ CSV (*.
PSI 9000 2U Serie 3.8.13 PV-Tabellenfunktion (Photovoltaik) 3.8.13.1 Einleitung Diese Funktion nutzt den internen XY-Generator, um mit einer aus vier Einstellwerten generierten IU-Tabelle das Netzgerät dazu zu bringen, ein Solarpanel oder eine Solarzelle mit bestimmten Eigenschaften zu simulieren.
PSI 9000 2U Serie Die Veränderung verschiebt den MPP und die Kurve auf der Y-Achse. Siehe Abbildung rechts. Der Wert Bestrahlung ist dabei ein Faktor für Impp. Die Kurve an sich wird dabei nicht verändert oder neu berechnet. I 1. Im Funktionsgenerator-Auswahlmenü tippen Sie auf 2. , dann und dann . Stellen Sie die vier Parameter gemäß den zu simulierenden Daten ein. Bestrahlung 0..100% ►►So konfigurieren Sie die PV-Tabelle MPP U Uoc 3.
PSI 9000 2U Serie 3.8.14.2 Anwendung Folgende Parameter können für die FC-Tabellenfunktion konfiguriert werden: Wert Einstellbereich Erläuterung Punkt 1: Uoc 0 V...UNenn Open circuit voltage, Leerlaufspannung Punkt 2+3: U 0 V...UNenn Punkt 2+3: I 0 A...INenn Spannung und Strom der beiden Punkte im U-I-Koordinatensystem. Sie repräsentieren zwei Stützpunkte auf der zu errechnenden Kennlinie Punkt 4: Isc 0 A...
PSI 9000 2U Serie 3.8.15 Fernsteuerung des Funktionsgenerators Der Funktionsgenerator ist fernsteuerbar, allerdings geschehen die Konfiguration und Steuern von Funktionen mittels einzelner Befehle und prinzipiell anders als bei manueller Bedienung. Die externe Dokumentation „Programmieranleitung ModBus & SCPI“ erläutert die Vorgehensweise.
PSI 9000 2U Serie 3.9 Weitere Anwendungen 3.9.1 Parallelschaltung in Master-Slave (MS) Mehrere Geräte gleicher Art und gleichen Modells können zu einer Parallelschaltung verbunden werden, um eine höhere Gesamtleistung zu erzielen. Dabei werden alle Netzgeräte an ihren DC-Ausgängen verbunden, sowie zusätzlich über den Master-Slave-Bus und den Share-Bus.
PSI 9000 2U Serie PSU 2 DC PSU n Master-Slave PSU n Master-Slave Master-Slave PSU n PSU 2 DC PSU 2 PSU 1 PSU 1 PSU 1 Alle Netzgeräte werden DC-seitig verbunden Nur bestimmte Netzgeräte werden DC-seitig verbunden Kein Netzgerät wird DC-seitig verbunden 3. Die beiden Geräte am Anfang und am Ende der Kette sollten bei langen Verbindungsleitungen terminiert werden.
PSI 9000 2U Serie 5. Legen Sie mit das Gerät als Master-Gerät fest. Falls es vorher als Slave definiert war, wird die Geräteadresse daraufhin auf 0 gesetzt und ist nicht mehr verstellbar (Master hat immer Adresse 0). 6. Wechseln Sie mit auf SEITE: 9 7. Übernehmen Sie die Einstellungen mit Bedienfeld und verlassen Sie das Einstellmenü bis zur Hauptanzeige. ►►Schritt 3: Master initialisieren Das Master-Gerät bzw. das Master-Slave-System müssen nun noch initialisiert werden.
PSI 9000 2U Serie 3.9.1.5 Alarm- und andere Problemsituationen Beim Master-Slave-Betrieb können, durch die Verbindung mehrerer Geräte und deren Zusammenarbeit, zusätzliche Problemsituationen entstehen, die beim Betrieb einzelner Geräte nicht auftreten können. Es wurden für solche Fälle folgende Festlegungen getroffen: • Falls ein oder mehrere Slave-Geräte DC-seitig ausfallen (Defekt, Überhitzung) schaltet der Master den Leistungseingang des System aus. Dann ist Interaktion durch Bedienpersonal erforderlich.
PSI 9000 2U Serie 3.9.3 Zwei-Quadranten-Betrieb (2QB) 3.9.3.1 Einleitung Diese Betriebsart bezieht sich auf die Verwendung einer Quelle, hier ein Netzgerät der Serie PSI 9000 2U, und einer kompatiblen Senke, z. B. eine elektronische Last der Serie ELR 9000. Die Quelle und die Senke treten abwechselnd in Funktion, um einen Prüfling wie z. B. eine Batterie, im Rahmen eines Funktions- oder Endtests gezielt zu laden und zu entladen.
E-LOAD n E-LOAD 1 PSU n ShareBus PSU 1 E.U.T Konfiguration C: Master-Slave Master-Slave PSI 9000 2U Serie Mehrere E-Lasten und mehrere Netzgeräte, plus ein Prüfling (E.U.T), zur Aufstockung für höhere Gesamtleistung. Der Lastenverbund und der Netzgeräteverbund bilden jeder für sich ein Gesamtsystem mit einer bestimmten Leistung. Auch hier gilt: die Nennwerte der beiden Systeme müssen zueinander passen, also z. B. 80 V DC-Ausgangsspannung der Lasten zu max. 80 V DC-Ausgangsspannung der Netzgeräte. 3.
PSI 9000 2U Serie 4. Instandhaltung & Wartung 4.1 Wartung / Reinigung Die Gerät erfordern keine Wartung. Reinigung kann, jenachdem in welcher Umgebung sie betrieben werden, früher oder später für die internen Lüfter nötig sein. Diese dienen zur Kühlung der internen Komponenten, die durch die zwangsweise entstehende, jedoch geringe Verlustleistung erhitzt werden. Stark verdreckte Lüfter können zu unzureichender Luftzufuhr führen und damit zu vorzeitiger Abschaltung des DC-Ausgangs wegen Überhitzung bzw.
PSI 9000 2U Serie 4.3 Firmwareaktualisierung (Updates) 4.3.1 Aktualisierung der Bedieneinheit (HMI) Die Bedieneinheit (HMI) kann wahlweise über die vordere oder die hintere USB-Buchse aktualisiert werden, wobei für die hintere USB-Buchse ein PC mit entsprechender Hilfsoftware benötigt würde und für die vordere USB-Buchse lediglich ein herkömmlicher, auf FAT32 formatierter USB-Stick mit der Update-Datei. Letztere Möglichkeit ist daher wesentlich einfacher.
PSI 9000 2U Serie 4.4 Nachjustierung (Kalibrierung) 4.4.1 Einleitung Die Geräte der Serie PSI 9000 verfügen über eine Nachjustierungsfunktion, die im Rahmen einer Kalibrierung dazu dient, Abweichungen zwischen den Stellwerten und tatsächlichen Werten bis zu einem gewissen Grad zu kompensieren. Gründe, die eine Nachjustierung der Gerätestellwerte nötig machen, gibt es einige: Bauteilalterung, Bauteilverschleiß, extreme Umgebungsbedingungen, häufige Benutzung.
PSI 9000 2U Serie ►►So gleichen Sie die Spannung ab 1. Spannungsmeßgerät am DC-Ausgang anschließen. Die Last auf etwas 2. 3. unter 5% des Nennstromes des Netzgerätes, hier z. B. 5 A, einstellen. In der Anzeige des PSI in das MENU wechseln, dann „Allg. Einstellungen“, dann Seite 5 und auf START. In der folgenden Übersicht wählen: Spannungs-Abgleich. Das Gerät schaltet dann den DC-Ausgang ein, setzt eine bestimmte Ausgangssppnung und mißt diese (U-mon). 4.
PSI 9000 2U Serie 5. Zubehör und Optionen 5.1 Übersicht 6. Service & Support 6.1 Übersicht 6.2 Kontaktmöglichkeiten Zubehör und Optionen werden, sofern nötig, mit eigener Dokumentation geliefert und werden in diesem Dokument nicht näher erläutert. Reparaturen, falls nicht anders zwischen Anwender und Lieferant ausgemacht, werden durch den Hersteller durchgeführt. Dazu muß das Gerät im Allgemeinen an den Hersteller eingeschickt werden. Es wird keine RMA-Nummer benötigt.
EA-Elektro-Automatik GmbH & Co. KG Entwicklung - Produktion - Vertrieb Helmholtzstraße 31-33 41747 Viersen Telefon: 02162 / 37 85-0 Telefax: 02162 / 16 230 ea1974@elektroautomatik.de www.elektroautomatik.
Elektro-Automatik GmbH Operating Guide PSI 9000 2U DC Laboratory Power Supply Doc ID: PSI92UEN Revision: 02 Date: 04/2014
PSI 9000 2U Series TABLE OF CONTENTS 1 GENERAL 1.1 1.1.1 1.1.2 1.1.3 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.8.1 1.8.2 1.8.3 1.8.4 1.8.5 1.9 1.9.1 1.9.2 1.9.3 1.9.4 1.10 1.10.1 1.10.2 1.10.3 1.10.4 1.10.5 1.10.6 1.10.7 1.10.8 1.10.9 1.10.10 1.10.11 1.10.12 2 About this document.......................................5 Retention and use...........................................5 Copyright.........................................................5 Validity............................................................
PSI 9000 2U Series 3.9 3.9.1 3.9.2 3.9.3 Other applications.........................................76 Parallel operation in master-slave mode (MS)...............................................................76 Series connection.........................................79 Two quadrant operation (2QO)....................80 4 SERVICE AND MAINTENANCE 5 ACCESSORIES AND OPTIONS 6 SERVICE & SUPPORT 4.1 4.2 4.2.1 4.3 4.3.1 4.3.2 4.4 4.4.1 4.4.2 4.4.3 5.1 Maintenance / cleaning...........................
PSI 9000 2U Series 1. General 1.1 About this document 1.1.1 Retention and use This document is to be kept in the vicinity of the equipment for future reference and explanation of the operation of the device. This document is to be delivered and kept with the equipment in case of change of location and/or user. 1.1.2 Copyright Reprinting, copying, also partially, usage for other purposes as foreseen of this manual are forbidden and breach may lead to legal process. 1.1.
PSI 9000 2U Series 1.5 Disposal of equipment 1.6 Product key A piece of equipment which is intended for disposal must, according to European laws and regulations (ElektroG, WEEE) be returned to the manufacturer for scrapping, unless the person operating the piece of equipment or another, delegated person is conducting the disposal.
PSI 9000 2U Series 1.8 Safety 1.8.1 Safety notices Mortal danger - Hazardous voltage • Electrical equipment operation means that some parts can be under dangerous voltage. Therefore all parts under voltage must be covered! This basically applies to all models, though 40 V models according to SELV can not generate hazardous DC voltage. • All work on connections must be carried out under zero voltage (output not connected to load) and may only be performed by qualified and informed persons.
PSI 9000 2U Series 1.8.3 Responsibility of the operator Operator is any natural or legal person who uses the equipment or delegates the usage to a third party, and is responsible during its usage for the safety of the user, other personnel or third parties. The equipment is in industrial operation. Therefore the operators are governed by the legal safety regulations.
PSI 9000 2U Series 1.8.5 Alarm signals The equipment offers various possibilities for signalling alarm conditions, however, not for danger situations. The signals may be optical (on the display as text) acoustic (piezo buzzer) or electronic (pin/status output of an analog interface). All alarms will cause the device to switch off the DC output.
PSI 9000 2U Series 1.9.3 Specific technical data Model 2U 1000 W PSI 9040-40 PSI 9080-40 PSI 9200-15 Input voltage 90...264 V AC 90...264 V AC 90...264 V AC Input connection 1ph,N,PE 1ph,N,PE 1ph,N,PE Input frequency 50/60 Hz 50/60 Hz 50/60 Hz Input fuse (internal) T16 A T16 A T16 A Leak current < 3.5 mA < 3.5 mA < 3.5 mA Power factor ~ 0.99 ~ 0.99 ~ 0.99 Max. output voltage UMax 40 V 80 V 200 V Max. output current IMax 40 A 40 A 15 A Max.
PSI 9000 2U Series Model 2U 1000 W PSI 9040-40 PSI 9080-40 PSI 9200-15 Adjustment range 0...30 Ω 0...60 Ω 0...400 Ω Accuracy ≤ 2% of max. resistance ± 0.3% of maximum current Internal resistance regulation (1 Display: Resolution See section „1.10.6.4. Resolution of the displayed values“ Display: Accuracy ≤ 0.
PSI 9000 2U Series Model 2U 1000 W PSI 9360-10 PSI 9500-06 PSI 9750-04 Input voltage 90...264 V AC 90...264 V AC 90...264 V AC Input connection 1ph,N,PE 1ph,N,PE 1ph,N,PE Input frequency 50/60 Hz 50/60 Hz 50/60 Hz Input fuse (internal) T16 A T16 A T16 A Leak current < 3.5 mA < 3.5 mA < 3.5 mA Power factor ~ 0.99 ~ 0.99 ~ 0.99 Max. output voltage UMax 360 V 500 V 750 V Max. output current IMax 10 A 6A 4A Max. output power PMax 1000 W 1000 W 1000 W Adjustment range 0.
PSI 9000 2U Series Model 2U 1000 W PSI 9360-10 PSI 9500-06 PSI 9750-04 Adjustment range 0...1080 Ω 0...2500 Ω 0...5625 Ω Accuracy ≤ 2% of max. resistance ± 0.3% of maximum current Internal resistance regulation (1 Display: Resolution See section „1.10.6.4. Resolution of the displayed values“ Display: Accuracy ≤ 0.
PSI 9000 2U Series Model 2U 1500 W PSI 9040-60 PSI 9080-60 PSI 9200-25 Input voltage 90...264 V AC 90...264 V AC 90...264 V AC - with additional derating 90...150 V AC 90...150 V AC 90...150 V AC Input connection 1ph,N,PE 1ph,N,PE 1ph,N,PE Input frequency 50/60 Hz 50/60 Hz 50/60 Hz Input fuse (internal) T16 A T16 A T16 A Leak current < 3.5 mA < 3.5 mA < 3.5 mA Power factor ~ 0.99 ~ 0.99 ~ 0.99 Max. output voltage UMax 40 V 80 V 200 V Max.
PSI 9000 2U Series Model 2U 1500 W PSI 9040-60 PSI 9080-60 PSI 9200-25 Adjustment range 0...20 Ω 0...40 Ω 0...240 Ω Accuracy ≤ 2% of max. resistance ± 0.3% of maximum current Internal resistance regulation (1 Display: Resolution See section „1.10.6.4. Resolution of the displayed values“ Display: Accuracy ≤ 0.
PSI 9000 2U Series Model 2U 1500 W PSI 9360-15 PSI 9500-10 PSI 9750-06 Input voltage 90...264 V AC 90...264 V AC 90...264 V AC - with additional derating 90...150 V AC 90...150 V AC 90...150 V AC Input connection 1ph,N,PE 1ph,N,PE 1ph,N,PE Input frequency 50/60 Hz 50/60 Hz 50/60 Hz Input fuse (internal) T16 A T16 A T16 A Leak current < 3.5 mA < 3.5 mA < 3.5 mA Power factor ~ 0.99 ~ 0.99 ~ 0.99 Max. output voltage UMax 360 V 500 V 750 V Max.
PSI 9000 2U Series Model 2U 1500 W PSI 9360-15 PSI 9500-10 PSI 9750-06 Adjustment range 0...720 Ω 0...1500 Ω 0...3750 Ω Accuracy ≤ 2% of max. resistance ± 0.3% of maximum current Internal resistance regulation (1 Display: Resolution See section „1.10.6.4. Resolution of the displayed values“ Display: Accuracy ≤ 0.
PSI 9000 2U Series Model 2U 3000 W PSI 9040-120 PSI 9080-120 PSI 9200-50 Input voltage 180...264 V AC 180...264 V AC 180...264 V AC - with additional derating 180...207 V AC 180...207 V AC 180...207 V AC Input connection 1ph,N,PE 1ph,N,PE 1ph,N,PE Input frequency 50/60 Hz 50/60 Hz 50/60 Hz Input fuse (internal) T16 A T16 A T16 A Leak current < 3.5 mA < 3.5 mA < 3.5 mA Power factor > 0.99 > 0.99 > 0.99 Max. output voltage UMax 40 V 80 V 200 V Max.
PSI 9000 2U Series Model 2U 3000 W PSI 9040-120 PSI 9080-120 PSI 9200-50 Adjustment range 0...10 Ω 0...20 Ω 0...120 Ω Accuracy ≤ 2% of max. resistance ± 0.3% of maximum current Internal resistance regulation (1 Display: Resolution See section „1.10.6.4. Resolution of the displayed values“ Display: Accuracy ≤ 0.
PSI 9000 2U Series Model 2U 3000 W PSI 9360-30 PSI 9500-20 PSI 9750-12 Input voltage 180...264 V AC 180...264 V AC 180...264 V AC - with additional derating 180...207 V AC 180...207 V AC 180...207 V AC Input connection 1ph,N,PE 1ph,N,PE 1ph,N,PE Input frequency 50/60 Hz 50/60 Hz 50/60 Hz Input fuse (internal) T16 A T16 A T16 A Leak current < 3.5 mA < 3.5 mA < 3.5 mA Power factor > 0.99 > 0.99 > 0.99 Max. output voltage UMax 360 V 500 V 750 V Max.
PSI 9000 2U Series Model 2U 3000 W PSI 9360-30 PSI 9500-20 PSI 9750-12 Adjustment range 0...360 Ω 0...750 Ω 0...1875 Ω Accuracy ≤ 2% of max. resistance ± 0.3% of maximum current Internal resistance regulation (1 Display: Resolution See section „1.10.6.4. Resolution of the displayed values“ Display: Accuracy ≤ 0.
PSI 9000 2U Series Views A - Mains switch B - Control panel C - Control interfaces (digital, analog) D - Exhausts E - Share Bus and remote sensing connectors F - DC output (terminal type 1) G - AC input fuse H - AC input connector 1.9.4 Figure 1 - Front side Page 22 Figure 2 - Rear side EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Germany Fon: +49 2162 / 3785-0 Fax: +49 2162 / 16230 www.elektroautomatik.de ea1974@elektroautomatik.
Figure 3 - Left hand side with DC terminal type 1 Figure 4 - Right hand side with DC terminal type 2 PSI 9000 2U Series EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Germany Fon: +49 2162 / 3785-0 Fax: +49 2162 / 16230 www.elektroautomatik.de ea1974@elektroautomatik.
PSI 9000 2U Series Figure 5 - View from above, with DC cover (terminal type 1) Page 24 EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Germany Fon: +49 2162 / 3785-0 Fax: +49 2162 / 16230 www.elektroautomatik.de ea1974@elektroautomatik.
PSI 9000 2U Series Figure 6 - Control Panel Overview of the elements of the operating panel For a detailed description see section „1.10.6. The control panel (HMI)“ and „1.10.6.2. Pushbuttons“. Touchscreen display (resistive) (1) Used for selection of set values, menus, conditions and display of actual values and status. The touchscreen can be operated with the fingers or with a stylus.
PSI 9000 2U Series 1.10 Construction and function 1.10.1 General description The electronic high performance power supplies of the PSI 9000 2U series are especially suitable for test systems and industrial controls due to their compact construction in a 19” enclosure with 2 height units (2U). Apart from basic functions of power supplies, set point curves can be produced in the integrated function generator (sine, rectangular, triangular and other curve types).
PSI 9000 2U Series 1.10.3 Scope of delivery 1 x Power supply device PSI 9000 2U 1 x Mains cord, 2 m, Euro plug (Schuko) and/or UK plug (depending on shipping destination) 1 x Printed operating guide 1 x Share Bus plug (separately or plugged) 1 x Remote sensing plug (separately or plugged) 1 x USB cable, 1.8 m 1 x Set of mounting brackets (for converting between 19” <-> desktop) 1 x CD “Drivers & Tools“ 1.10.
PSI 9000 2U Series 1.10.6 The control panel (HMI) The HMI (Human Machine Interface) consists of a display with touchscreen, two rotary knobs, a pushbutton and a USB-A port. 1.10.6.1 Touchscreen display The graphic touchscreen display is divided into a number of areas. The complete display is touch sensitive and can be operated by finger or stylus to control the equipment.
PSI 9000 2U Series • Status display (upper right) This area displays various status texts and symbols: Display Description Locked The HMI is locked Unlocked The HMI is unlocked Output ON DC output is switched on Output OFF DC output is switched off Remote The device is under remote control from.... Analog ....the built-in analog interface USB & others ....
PSI 9000 2U Series 1.10.6.3 Rotary knobs As long as the device is in manual operation, the two rotary knobs are used to adjust set values, as well as setting the parameters in the pages SETTINGS and MENU. For a detailed description of the individual functions see section „3.3 Manual operation“ on page 43. Both rotary knobs have an additional pushbutton function whereby the decimal position of the value to be set is moved.
PSI 9000 2U Series 1.10.7 USB port (rear side) The USB-B port on the back side of the device is provided for communication with the device and for firmware updates. The included USB cable can be used to connect the device to a PC (USB 2.0 or 3.0). The driver is delivered on the included CD and installs a virtual COM port. Details for remote control can be found on the web site of the manufacturer or on the included CD.
PSI 9000 2U Series 1.10.10 Share Bus-Connection The 2 pole WAGO socket (“Share”) on the back side of the device is provided for connection to equally named sockets on compatible power supplies series to achieve a balanced load current distribution during parallel connection. The socket is also used to connect the power supply to compatible electronic loads, in order to build a two-quadrants operation setup.
PSI 9000 2U Series 2. Installation & commissioning 2.1 Transport and storage 2.1.1 Transport • The handles on the front side of the device are not for carrying! • Because of its weight, transport by hand should be avoided where possible. If unavoidable then only the housing should be held and not on the exterior parts (handles, DC output terminal, rotary knobs).
PSI 9000 2U Series 2.3.2 Preparation Mains connection for a PSI 9000 2U series device is done via the included 2 meters long 3 pole mains cord. In case a different AC wiring is required, make sure that the other cable has at least a cross section of 2.5 mm² (AWG 12) is used. Dimensioning of the DC wiring to the load/consumer has to reflect the following: • The cable cross section should always be specified for at least the maximum current of the device.
PSI 9000 2U Series 2.3.4 Connection to AC supply • The device can be connected to any wall socket or multi-socket outlet, as long as those feature a safety contact (PE) and are capable for 16 A.
PSI 9000 2U Series 2.3.5.2 Cable lead and plastic cover A plastic cover for contact protection is included for the DC terminal. It should always be installed. The cover for type 2 (see picture above) is fixed to the connector itself, for type 1 to the back of the device. Furthermore the cover for type 1 has break outs so that the supply cable can be laid in various directions.
PSI 9000 2U Series 2.3.7 Connection of remote sensing In order to compensate, to a certain degree, the voltage loss in a DC cable, the device provides the possibility to connect the remote sensing input “Sense” (rear side) to the load. The device recognizes the remote sensing mode automatically and regulates the output voltage (only in CV operation) at the load rather than at its own DC output. In the technical specifications (see section „1.9.3.
PSI 9000 2U Series 2.3.8 Installation of an AnyBus interface module The various interface modules which are available for the device can be retrofitted by the user and are exchangeable with other modules. The settings for the currently installed module vary and need to be checked and, if necessary, corrected on initial installation and after module exchange. • • • • Common ESD protection procedures apply when inserting or exchanging a module.
PSI 9000 2U Series 2.3.10 Connecting the “Share” bus The “Share” bus connector on the back side is intended to balance the current of multiple units in parallel operation, especially when using the integrated function generator of the master unit. It is recommended to connect the Share bus of any unit involved in parallel operation. Alternatively, it can be connected to a compatible electronic load, like from series ELR 9000, in order to run a two-quadrants operation.
PSI 9000 2U Series 3. Operation and application 3.
PSI 9000 2U Series 3.2.3 Power regulation / constant power / power limiting Power regulation, also known as power limiting or constant power (CP), keeps the DC output power of a power supply constant if the current flowing to the load in relation to the output voltage and the resistance of load reaches the adjusted value according to P = U * I resp. P = U² / R. The power limiting then regulates the output current according to I = sqr(P / R), where R is the load’s resistance.
PSI 9000 2U Series 3.2.5 Alarm conditions This section only gives an overview about device alarms. What to do in case your device indicates an alarm condition is described in section „3.5. Alarms and monitoring“. As a basic principle, all alarm conditions are signalled optically (Text + message in the display), acoustically (if activated) and as a readable status via the digital interface. With any alarm occurring, the DC output of the device is switched off.
PSI 9000 2U Series 3.3 Manual operation 3.3.1 Switching on the device The device should, as far as possible, always be switched on using the toggle switch on the front of the device. Alternatively this can take place using an external cutout (contactor, circuit breaker) of suitable current capacity. After switching on, the display will first show the manufacturers logo (approx. 10 s) followed by the manufacturers name, address, device model, firmware version(s), serial number and item number (approx.
MENU Page 44 EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Germany Fon: +49 2162 / 3785-0 Fax: +49 2162 / 16230 Page 5 Page 6 User Profile 4 User Profile 5 Event P Event I Event U Page 7 Enable R mode: Yes | No Page 4 User Profile 3 OPD = {0W...Pnom} Aktion = {NO | SIGNAL | WARNING |ALARM} OCD = {0A...Inom} Aktion = {NO | SIGNAL | WARNING |ALARM} UCD = {0A...Inom} Aktion = {NO | SIGNAL | WARNING |ALARM} OVD = {0V...Unom} Aktion = {NO | SIGNAL | WARNING |ALARM} UVD = {0V...
MENU EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Germany Fon: +49 2162 / 3785-0 Fax: +49 2162 / 16230 www.elektroautomatik.de ea1974@elektroautomatik.de UI-IU Arbitrary Ramp DIN 40839 Trapezoid U t2= 0.1ms...36000s (1ms) Ue(DC)= 0V...Umax Load from USB t1= 0.1ms...36000s (1ms) Uend= 0V...Umax I Angle= 0°...359° Us(DC)= 0V...Umax Ustart= 0V...Umax t4= 0.1ms...36000s (1ms) t3= 0.1ms...36000s (1ms) t2= 0.1ms...
MENU HMI Setup Communication Page 46 EA Elektro-Automatik GmbH Helmholtzstr. 31-33 • 41747 Viersen Germany Brightness: 1...10 Lock all Sound on Sound on Panel Contrast HMI Lock Key Sound Alarm Sound TP Calibration HMI Update Always on English (Interface type) Ethernet Backlight Setup Language Configure interface Sound off Sound off ON/OFF possible Off after 60 sec. Other lang. Deutsch ... PSI 9000 2U Series Fon: +49 2162 / 3785-0 Fax: +49 2162 / 16230 www.elektroautomatik.
PSI 9000 2U Series 3.3.3.1 Menu “General Settings” Element Allow remote control Share Bus mode Output after power ON Analog interface range P. Description 1 Selection “NO” means that the device cannot be remotely controlled over either the digital or analog interfaces. If remote control is not allowed, the status will be shown as “local” in the status area on the main display. See also section 1.10.6.1 1 For parallel operation of multiple units or two-quadrants operation (see „3.9.3.
PSI 9000 2U Series 3.3.3.5 Menu “About HW, SW...” This menu page displays an overview of device relevant data such as serial number, article number etc. 3.3.3.6 Menu “Function Generator” See „3.8 The function generator“ on page 61. 3.3.3.7 Menu “Communication” Here settings for digital communication via the optional interface modules (abbr. IF) of the IF-AB series are made. The touch area “Configure interface” opens one or more settings pages, depending on the module in use.
PSI 9000 2U Series IF Level 1 IP Settings Level 2 DHCP Manual Profinet/IO, 1 & 2 Port DNS 1 DNS 2 Devicenet Description The IF allows a DHCP server to allocate an IP address, a subnet mask and a gateway. If no DHCP server is in the network then network parameters will be set as defined in point “Manual” IP This option is activated by default. An IP address can be maually allocated. Gateway Here a gateway address can be allocated if required..
PSI 9000 2U Series 3.3.3.8 Menu “HMI settings” These settings refer exclusively to the control panel (HMI). Element Language Description Selection of the display language. Currently (date: 04-14-2014) available are: German, English Backlight Setup Panel Contrast HMI Lock Key Sound Alarm Sound HMI Update TP Calibration 3.3.4 Additional languages (up to three can be integrated) can be implemented on demand and installed into the HMI via update.
PSI 9000 2U Series 3.3.5 Changing the operating mode In general, the manual operation of a PSI 9000 2U distinguishes between two operating modes which are tied to set value input using the rotary knobs or ten-key pad. This assignment must be changed if one of the three set values is to be adjusted which is currently not available. ►►How to change the operating mode: 1. On the main screen tap the touch area 2.
PSI 9000 2U Series ►How to adjust values U, I or P via direct input: 1. In the main screen, depending on the rotary knob assignment, values can be set for voltage (U), current (I) or power (P) via direct input by tapping on the set/actual value display areas, e.g in the uppermost area of voltage. 2. Enter the required value using the ten-key pad. Similar to a pocket calculator the key clears the input. Decimal values are set by tapping the point key. For example, 54.3 V is set with and . 3.
PSI 9000 2U Series 3.3.7 Switching the DC output on or off The DC output of the device can be manually or remotely switched on and off. This can be restricted in manual operation by the control panel being locked. ►►How to manually switch the DC output on or off 1. As long as the control panel is not fully locked press the button ON/OFF. Otherwise you are asked to disable the HMI lock first. 2.
PSI 9000 2U Series 3.4.3 Remote control via a digital interface 3.4.3.1 Selecting an interface The device supports, in addition to the built-in USB port, the following optional interface modules for user preference: Short ID IF-AB-CANO IF-AB-RS232 IF-AB-PBUS IF-AB-ETH1P IF-AB-PNET1P IF-AB-DNET IF-AB-MBUS IF-AB-ETH2P IF-AB-MBUS2P IF-AB-PNET2P Art. nr.
PSI 9000 2U Series 3.4.4 Remote control via the analog interface (AI) 3.4.4.
PSI 9000 2U Series 3.4.4.3 Analog interface specification Pin Name Type* Description 1 VSEL AI Set voltage value 2 CSEL AI Set current value 3 VREF AO Reference voltage 4 DGND POT Ground for all digital signals Levels Electrical properties 0…10 V or. 0...5 V correspond Accuracy < 0.2% to 0..100% of UNom 0…10 V or. 0...5 V correspond Input impedance Ri >40 kΩ...100 kΩ to 0..100% of INom Tolerance < 0.
PSI 9000 2U Series 3.4.4.5 Application examples a) Switching off output with pin “Rem-SB” The pin Rem-SB can be used in remote control to switch the output on and off. It is recommended that a low resistance contact such as a switch, relay or transistor is used to switch the pin to ground (DGND). A digital output, e.g. from a PLC, may be unable to cleanly effect this as it may not be of low enough resistance. Check the specification of the controlling application. See also 3.4.4.4 above.
PSI 9000 2U Series 3.5 Alarms and monitoring 3.5.1 Definition of terms There is a clear distinction between device alarms (see „3.2.5. Alarm conditions“) such as overvoltage protection or overheating protection, and user defined events such as OVD (overvoltage detection).
PSI 9000 2U Series Alarm Meaning OverTemperature OT Description Indication Triggers an alarm if the internal temperature exceeds a certain limit. The Display, analog DC output will be switched off. IF, digital IF ►►How to configure the device alarms 1. Tap the touch area on the main screen. 2. On the right side tap the white arrow to select “2. Protect”. 3. Set the limits for the equipment alarm relevant to your application if the default value of 110% is unsuitable.
PSI 9000 2U Series As soon as an event is set up with an action other than “NONE” and with accepted settings, an incident can occur whether the DC output is switched on or off. On leaving the pages “User events” or “Settings” an event can be directly displayed. User events are an integral part of the actual user profile. Thus, if another user profile, or the default profile, is selected and used, the events will be either differently or not configured. The set values can be entered using the ten-key tab.
PSI 9000 2U Series 3.8 The function generator 3.8.1 Introduction The built-in function generator is, like the equally named electronic devices, able to create various signal forms and apply these to set values for voltage or current. Whilst R mode is activated, access to the function generator is not available. The generator functions can be manually operated completely on the device.
PSI 9000 2U Series 3.8.4 Manual operation 3.8.4.1 Function selection and control Via the touchscreen one of the functions described above can be called up, configured and controlled. Selection and configuration are only possible when the output is switched off. ►►How to select a function and adjust parameters 1. Tap the touch area on the main screen.
PSI 9000 2U Series ►►How to start and stop a function 1. The function can be started either by tapping or pushing the “On/Off” button, if the DC output is currently switched off. The function then starts immediately. In case START is used while the DC output is still switched off, the DC output will be switched on automatically. During the progress of the functions sine wave, rectangular wave, triangular wave, trapezoidal wave or ramp no actual values are displayed. 2.
PSI 9000 2U Series Schematic diagram: Application and result: A triangular wave signal for output current (only effective in current limiting) or output voltage is generated. The positive and negative slope times are variable and can be set independently. A The offset shifts the signal on the Y-axis. Amplitude The sum of the intervals t1 and t2 gives the cycle time and its reciprocal is the frequency. Offset Example: a frequency of 10 Hz is required and would lead to periodic duration of 100 ms.
PSI 9000 2U Series 3.8.8 Trapezoidal function The following parameters can be configured for a trapezoidal curve function: Value Range Description I(A), U(A) 0...(Nominal value - (Off)) of U, I A = Amplitude of the signal to be generated I(Off), U(Off) 0...(Nominal value - (A)) of U, I Off = Offset, based on the foot of the trapezium t1 0.1 ms...36000 s Time for the positive slope of the trapezoidal wave signal. t2 0.1 ms...36000 s Time for the top value of the trapezoidal wave signal.
PSI 9000 2U Series 3.8.10 Arbitrary function The arbitrary (freely definable) function offers the user further scope. Up to 100 sequences are available for use for current I and voltage U, all of which have the same parameters but which can be differently configured so that a complex function process can be built up. The 100 sequences can run one after another in a sequence block, and this sequence block can then be repeated many times or endlessly.
PSI 9000 2U Series Schematic diagram: Applications and results: A Focussing 1 cycle of 1 sequence from 100: The DC values at start and end are the same but the AC (amplitude) not. The end value is higher than the start so that the amplitude increases with each new half sine wave continuously through the sequence. This, of course, only if the sequence time and frequency allow for multiple waves to be created. e.g. for f=1 Hz and Seq.
PSI 9000 2U Series By linking together a number of differently configured sequences, complex progressions can be created. Smart configuration of the arbitrary generator can be used to match triangular, sine, rectangular or trapezoidal wave functions and thus, e.g. a sequence of rectangular waves with differing amplitudes or duty cycles could be produced. Assignment to either U or I makes up to 100 sequences available for either current or voltage but not a mix.
PSI 9000 2U Series 3.8.10.1 Loading and saving the arbitrary function The 100 sequences of the arbitrary function, which can be manually configured with the control panel of the device and which are applicable either to voltage (U) or current (I), can be saved to or loaded from a common USB flash drive via the front side USB port. Generally, all 100 sequences are saved or loaded using a text file of type CSV (semicolon separator), which represents a table of values.
PSI 9000 2U Series ►►How to save a sequence table (100 sequences) to a USB flash drive: 1. Do not plug the USB flash drive yet or remove it. 2. Access the function selection menu of the function generator via MENU -> Function Generator -> Arbitrary 3. Tap on , then . The device will request you to plug the USB flash drive now. 4. After plugging it, the device will try to access the flash drive and find the folder HMI_FILES and read the content.
PSI 9000 2U Series In the IU function the assignment of the values is the other way round, the behaviour, however, the same. Thus the behaviour of the load or the current and power consumption can be controlled with dependance on output voltage and step changes can be created. The IU function suit very good for the simulation of solar panels in photovoltaics related tests. Uploading of a table from a USB flash drive must use text files in CSV format (*.csv).
PSI 9000 2U Series 3.8.13 PV table function (photovoltaics) 3.8.13.1 Preface This function uses the standard XY generator to make the power supply simulate solar panels or solar cells with certain characteristics. The device calculates an IU table from four typical values. While the function is running, the user can adjust a parameter “Irradiance” between 0% (darkness) and 100% (bright light) in 1% steps to simulate different light situations.
PSI 9000 2U Series Varying this parameter shifts the MPP and the PV curve along the Y axis. Also see diagram to the right. The value Irradiance is here used as a factor for the current Impp. The curve itself is not permanently re-calculated. I 1. In the function generator menu tap on , then MPP and then . Adjust the four parameters as required for the simulation. Irradiation 0..100% ►►How to configure the PV table Uoc 2. 3.
PSI 9000 2U Series 3.8.14.2 Usage The following parameters can be set for the FC table function: Value Range Description Point 1: Uoc 0 V...UNom Open circuit voltage at no load Point 2+3: U 0 V...UNom Point 2+3: I 0 A...INom Voltage and current define the position of these two points in the U-I coordinate system, which represent two supporting points on the curve to be calculated Point 4: Isc 0 A...
PSI 9000 2U Series 3.8.15 Remote control of the function generator The function generator can be remotely controlled but configuration and control of the functions with individual commands is different from manual operation. The external documentation “Programming Guide ModBus & SCPI” explains the approach.
PSI 9000 2U Series 3.9 Other applications 3.9.1 Parallel operation in master-slave mode (MS) Multiple devices of same kind and model can be connected in parallel in order to create a system with higher total current and hence higher power. For true master-slave operation, the units have to be connected with their DC outputs, their master-slave bus and their Share bus. The master-slave bus is a digital bus which makes the system work as one big unit regarding adjusted values, actual values and status.
PSI 9000 2U Series 3. The two units at the beginning and end of the chain should be terminated, if long connection cables are used. This is achieved using a 3-pole DIP switch which is positioned on the back side of the unit next to the MS connectors. Position: not terminated (standard) Switches 2 and 3 serve as a BIAS network and should be switched on to avoid undefined bus noise. ► Position: terminated Switch 1 enables the bus termination resistor.
PSI 9000 2U Series 3.9.1.4 Operating the master-slave system After successful configuration and initialisation of the master and slave units, these will show their status in the displays. While the master merely shows “Master” in the status area, the slave(s) will continuously show like this, as long they are in remote control by the master: The slaves can no longer be controlled manually or remotely, neither via the analog nor via digital interfaces.
PSI 9000 2U Series 3.9.2 Series connection Series connection of two or multiple devices is basically possible.
PSI 9000 2U Series 3.9.3 Two quadrant operation (2QO) 3.9.3.1 Introduction This way of operating refers to the use of a source, in this case a power supply of this series PSI 9000 2U, and a sink, for example a series ELR 9000 electronic load.
E-LOAD n E-LOAD 1 PSU n ShareBus PSU 1 E.U.T Configuration C: Master-Slave Master-Slave PSI 9000 2U Series Multiple e-loads and Multiple power supplies, plus 1 test object (E.U.T), for raising the total performance. The load combination and the power supply combination create in each case a total system with a defined power. It is necessary also here to match the nominal values of the two systems. i.e an 80 V DC output of the loads to a max. 80 V DC output of the power supplies. 3.9.3.
PSI 9000 2U Series 4. Service and maintenance 4.1 Maintenance / cleaning The device needs no maintenance. Cleaning may be needed for the internal fans, the frequency of cleanse is depending on the ambient conditions. The fans serve to cool the components which are heated by the inherent power loss. Heavily dirt filled fans can lead to insufficient airflow and therefore the DC output would switch off too early due to overheating or possibly lead to defects.
PSI 9000 2U Series 4.3 Firmware updates 4.3.1 HMI update The control panel (HMI) can be updated via the front or back USB ports, whereby the back USB port requires a PC with suitable software and the front USB only requires a FAT32 formatted USB flash drive with the update file. Hence the latter option is much simpler. Firmware updates should only be installed when they can eliminate software bugs in the firmware of your device or contain new features. ►►How to update the control panel firmware: 1.
PSI 9000 2U Series 4.4 Calibration 4.4.1 Preface The devices of series PSI 9000 feature a function to readjust the most important output values when doing a calibration and in case these values have moved out of tolerance. The readjustment is limited to compensate small differences of up to 1% or 2% of the max. value.
PSI 9000 2U Series ►►How to calibrate the voltage 1. Connect a multimeter to the DC output. Connect a load and set it to less 2. 3. than 5% of the nominal current of the power supply as load current, in this example let’s use 5 A. In the display, tap MENU, then „General Settings“, then go to Page 5 and then tap START. In the next screen select: Voltage calibration. The power supply will switch the DC output on, set a certain output voltage and start to measure it (U-mon). 4.
PSI 9000 2U Series 5. Accessories and options 5.1 Overview 6. Service & Support 6.1 General 6.2 Contact options Accessories and options are, when necessary, delivered with their own documentation and are not detailed further in this document. Repairs, if not otherwise arranged between supplier and customer, will be carried out by the manufacturer. For this the device must generally be returned to the manufacturer. No RMA number is needed.
EA-Elektro-Automatik GmbH & Co. KG Entwicklung - Produktion - Vertrieb Helmholtzstraße 31-33 41747 Viersen Telefon: 02162 / 37 85-0 Telefax: 02162 / 16 230 ea1974@elektroautomatik.de www.elektroautomatik.