Datasheet

Irrtümer und Änderungen vorbehalten / Subject to modication without notice, errors and omissions excepted
© EA-Elektro-Automatik GmbH, 2015
19
AC input
The equipment uses an active Power Factor Correction (short:
PFC), enabling worldwide use on a mains input from 90 V
AC
up
to 264 V
AC
. Models with 1.5 kW will derate their output power
to 1 kW below input voltages of 150 V
AC
.
Auto-ranging power stage
All models are equipped with a exible auto-ranging
output stage which provides a higher output voltage
at lower output current, or a higher output current
at lower output voltage, always limited to the max.
nominal output power. The maximum power set value
is adjustable with these models. Therefore, a wide
range of applications can already be covered by the
use of just one unit.
DC output
DC output voltages between 0...40 V and 0...750 V, output
currents between 0...4 A and 0...60 A and output power ratings
between 320 W and 0...1500 W are available.
Current, voltage and power can thus be adjusted continuously
between 0% and 100%, no matter if manually or remotely con-
trolled (analog or digital).
The output terminals are located on the front side of the devices.
Compared to other power supply series, the PSI 9000 DT
feature a built-in, additional output lter to achieve much lower
ripple, i. e. low noise on the DC output voltage.
Discharge circuit
Models with a nominal output voltage of 200 V or higher include
a discharge circuit for the output capacities. For no load or low
load situations, it ensures that the dangerous output voltage can
sink to under 60 V DC after the DC output has been switched
off. This value is considered as limit for voltages dangerous to
human safety.
Protective features
For protection of the equipment connected, it is possible to set
an overvoltage protection threshold (OVP), as well as one for
overcurrent (OCP) and overpower (OPP).
As soon as one of these thresholds is reached for any reason,
the DC output will be immediately shut off and a status signal
will be generated on the display and via the interfaces.
There is furthermore an overtemperature protection, which will
shut off the DC output if the device overheats.
Remote sensing
The standard sensing input can be connected directly to the
load in order to compensate voltage drops along the cables. If
the sensing input is connected to the load, the power supply
will detect this and adjust the output voltage automatically to
ensure the accurate required voltage is available at the load.
Built-in analog interface
There is a galvanically isolated analog interface
terminal, located on the rear of the device. It
offers analog inputs to set voltage, current and
power from 0...100% through control voltages
of 0 V...10 V or 0 V...5 V. To monitor the output
voltage and current, there are analog outputs
with voltage ranges of 0 V...10 V or 0 V...5 V.
Also, several inputs and outputs are available
for controlling and monitoring the device status.
AC-Eingang
Die Geräte besitzen alle eine aktive PFC (Leistungsfaktor-
Korrektur) und sind für den weltweiten Einsatz mit einem Netz-
eingang von 90 V
AC
bis 264 V
AC
ausgelegt. Bei Modellen mit
1,5 kW wird die Ausgangsleistung bei einer Eingangsspannung
<150 V
AC
auf 1 kW reduziert.
Flexible Leistungsregelung
Alle Modelle haben eine exible, leistungsgeregelte
Ausgangsstufe, die bei hoher Ausgangsspannung
den Strom oder bei hohem Ausgangsstrom die
Spannung so reduziert, daß die maximale Ausgangs-
leistung nicht überschritten wird. Der maximale Lei-
stungswert ist hierbei einstellbar.
So kann mit nur einem Gerät ein breites Anwendungs-
spektrum abgedeckt werden.
DC-Ausgang
Zur Verfügung stehen Modelle mit DC-Ausgangsspannungen
zwischen 0...40 V und 0...750 V, Strömen zwischen 0...4 A und
0...60 A, sowie Leistungen zwischen 320 W und 0...1500 W.
Strom, Spannung und Leistung sind somit jeweils zwischen
0% und 100% kontinuierlich einstellbar, egal ob bei manueller
Bedienung oder per Fernsteuerung über analoge oder digitale
Schnittstelle.
Der Ausgang bendet sich auf der Vorderseite der Geräte.
Gegenüber anderen Netzgerätenserien bietet die Serie PSI
9000 DT durch einen eingebauten. zusätzlichen Ausgangsl-
ter eine deutlich geringere Restwelligkeit (low noise) der DC-
Ausgangsspannung.
Entlade-Schaltung
Modelle mit einer Nennspannung ab 200 V beinhalten eine
Entladeschaltung. Diese entlädt nach dem Ausschalten des DC-
Ausgangs die Ausgangskapazitäten und sorgt bei keiner oder
geringer Last dafür, daß die teils gefährlich hohe Ausgangs-
spannung in max. 10 Sekunden auf unter 60 V DC sinkt. Die-
ser Wert gilt als Grenze für berührungsgefährliche Spannung.
Schutzfunktionen
Um die angeschlossenen Verbraucher vor Beschädigung zu
schützen, können eine Überspannungsschwelle (OVP), eine
Überstromschwelle (OCP), sowie eine Überleistungsschwelle
(OPP) eingestellt werden. Bei Erreichen eines dieser Werte wird
der DC-Ausgang abgeschaltet und es wird eine Alarmmeldung
in der Anzeige, sowie auf den Schnittstellen ausgeben. Weiter-
hin gibt es einen Übertemperaturschutz, der den DC-Ausgang
bei Überhitzung des Gerätes abschaltet.
Fernfühlung (Sensing)
Der serienmäßig vorhandene Fernfühlungseingang (Sense)
kann direkt am Verbraucher angeschlossen werden, um Span-
nungsabfall auf den Lastleitungen zu kompensieren. Das Gerät
erkennt selbständig, wenn die Senseleitungen angeschlossen
sind und regelt die Ausgangsspannung direkt am Verbraucher.
Der Eingang bendet sich auf der Vorderseite des Gerätes.
Eingebaute Analogschnittstelle
Eine galvanisch getrennte Analogschnittstelle
bendet sich auf der Rückseite des Gerätes.
Sie verfügt über analoge Steuereingänge mit
0...10 V oder 0...5 V um Spannung, Strom und
Leistung von 0...100% zu programmieren.
Ausgangsspannung und Ausgangsstrom kön-
nen über analoge Monitorausgänge mit 0...10 V
oder 0...5 V ausgelesen werden. Weiterhin gibt
es Statuseingänge und -ausgänge.
EA-PSI 9000 DT 320 W - 1500 W
DC-LABORNETZGERÄTE MIT GERINGER RESTWELLIGKEIT / LOW NOISE LABORATORY DC POWER SUPPLIES