User Manual

Page 3
EA Elektro-Automatik GmbH
Helmholtzstr. 31-33 • 41747 Viersen
Germany
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
www.elektroautomatik.de
[e-mail]
PS 9000 2U Series
TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................5
1.1.1 Retention and use ..........................................5
1.1.2 Copyright ........................................................5
1.1.3 Validity ............................................................5
1.2 Explanation of symbols ..................................5
1.3 Warranty ......................................................... 5
1.4 Limitation of liability ........................................5
1.5 Disposal of equipment ...................................6
1.6 Product key ....................................................6
1.7 Intended usage ..............................................6
1.8 Safety .............................................................7
1.8.1 Safety notices .................................................7
1.8.2 Responsibility of the user...............................7
1.8.3 Responsibility of the operator .......................8
1.8.4 User requirements .........................................8
1.8.5 Alarm signals ..................................................9
1.9 Technical Data ...............................................9
1.9.1 Approved operating conditions ......................9
1.9.2 General technical data ................................... 9
1.9.3 Specictechnicaldata .................................10
1.9.4 Views ............................................................22
1.10 Construction and function ............................ 26
1.10.1 General description ...................................... 26
1.10.2 Block diagram ..............................................26
1.10.3 Scope of delivery .........................................27
1.10.4 Accessories .................................................. 27
1.10.5 Options .........................................................27
1.10.6 The control panel (HMI) ...............................28
1.10.7 USB port (rear side) .....................................30
1.10.8 Ethernet port (rear side) ...............................30
1.10.9 Analog interface ...........................................30
1.10.10 Share Bus-Connection ................................31
1.10.11 Sense connector (remote sensing) .............31
2
INSTALLATION & COMMISSIONING
2.1 Transport and storage .................................32
2.1.1 Transport ......................................................32
2.1.2 Packaging ....................................................32
2.1.3 Storage ......................................................... 32
2.2 Unpacking and visual check ........................ 32
2.3 Installation ....................................................32
2.3.1 Safety procedures before installation and
use ................................................................32
2.3.2 Preparation ................................................... 33
2.3.3 Installing the device .....................................33
2.3.4 Connection to AC supply .............................34
2.3.5 Connection to DC loads ...............................34
2.3.6 Grounding of the DC output ........................35
2.3.7 Connection of remote sensing ....................36
2.3.8 Connecting the “Share” bus ........................37
2.3.9 Connecting the analog interface .................37
2.3.10 Connecting the USB port (rear side) ...........37
2.3.11 Initial commission ......................................... 38
2.3.12 Initial network setup .....................................38
2.3.13 Commissionafterarmwareupdateora
long period of non-use .................................38
3
OPERATION AND APPLICATION
3.1 Personal safety ............................................39
3.2 Operating modes .........................................39
3.2.1 Voltage regulation / Constant voltage .........39
3.2.2 Current regulation / constant current / current
limiting ..........................................................39
3.2.3 Power regulation / constant power / power
limiting ..........................................................40
3.2.4 Alarm conditions ..........................................40
3.3 Manual operation .........................................41
3.3.1 Switching on the device ...............................41
3.3.2 Switching off the device ...............................41
3.3.3 Congurationinthesetupmenu .................41
3.3.4 Adjustment limits ..........................................45
3.3.5 Display modes for actual and set values ....46
3.3.6 Manual adjustment of set values .................46
3.3.7 The quick menu ...........................................47
3.3.8 Switching the DC output on or off ................47
3.4 Remote control ............................................. 48
3.4.1 General .........................................................48
3.4.2 Control locations ..........................................48
3.4.3 Remote control via a digital interface ..........48
3.4.4 Remote control via the analog interface
(AI) ................................................................49
3.5 Alarms and monitoring ................................. 52
3.5.1 Denitionofterms ........................................52
3.5.2 Device alarm handling .................................52
3.6 Control panel (HMI) lock ..............................53
3.7 Loadingandsavingauserprole ...............54
3.8 Other applications ........................................55
3.8.1 Parallel operation in Share Bus mode ........55
3.8.2 Series connection ........................................56
3.8.3 Two quadrant operation (2QO) ...................57
4
SERVICE AND MAINTENANCE
4.1 Maintenance / cleaning ................................ 59
4.2 Faultnding/diagnosis/repair...................59
4.2.1 Replacing a defect mains fuse ....................59
4.3 Firmware updates ........................................60
4.3.1 Update of control panel (HMI) .....................60
4.3.2 Update of communication unit (KE) ............60
4.4 Calibration (readjustment) ...........................61
4.4.1 Preface .........................................................61
4.4.2 Preparation ................................................... 61
4.4.3 Calibration procedure ..................................61