Datasheet
© EA Elektro-Automatik, 2017 Irrtümer und Änderungen vorbehalten / Subject to modication without notice, errors and omissions excepted 61
Programmierbare DC-Tischnetzgeräte / Programmable desktop DC Power supplies
EA-PS 3000 C 160 W - 640 W
AC-Anschluß
Die Geräte besitzen alle eine aktive PFC (Leistungsfaktor-Korrektur) und
sind für den weltweiten Einsatz mit einem Netzeingang von 90 V
AC
bis 264
V
AC
ausgelegt.
Flexible Leistungsregelung
Alle Modelle haben eine exible, leistungsgeregelte Aus-
gangsstufe, die bei hoher Ausgangsspannung den Strom
oder bei hohem Ausgangsstrom die Spannung so redu-
ziert, daß die maximale Ausgangsleistung nicht über-
schritten wird. Der maximale Leistungswert ist hierbei
einstellbar.
So kann mit nur einem Gerät ein breites Anwendungs-
spektrum abgedeckt werden.
DC-Ausgang
Zur Verfügung stehen Modelle mit DC-Ausgangsspannungen zwischen
0...40 V und 0...200 V, Strömen zwischen 0...2 A und 0...40 A, sowie Lei-
stungen zwischen 0...160 W und 0...640 W.
Strom, Spannung und Leistung sind somit jeweils zwischen 0% und 100%
kontinuierlich einstellbar, egal ob bei manueller Bedienung oder per Fern-
steuerung über analoge oder digitale Schnittstelle. Der Ausgang bendet
sich auf der Vorderseite der Geräte.
Schutzfunktionen
Um die angeschlossenen Verbraucher vor Beschädigung zu schützen, kön-
nen eine Überspannungsschwelle (OVP), eine Überstromschwelle (OCP),
sowie eine Überleistungsschwelle (OPP) eingestellt werden. Bei Erreichen
eines dieser Werte wird der DC-Ausgang abgeschaltet und es wird eine
Alarmmeldung in der Anzeige, sowie auf den Schnittstellen ausgeben.
Weiterhin gibt es einen Übertemperaturschutz, der den DC-Ausgang bei
Überhitzung des Gerätes abschaltet.
Fernfühlung (Sensing)
Der serienmäßig vorhandene Fernfühlungseingang (Sense) kann direkt am
Verbraucher angeschlossen werden, um Spannungsabfall auf den Lastlei-
tungen zu kompensieren. Das Gerät erkennt selbständig, wenn die Sense-
leitungen angeschlossen sind und regelt die Ausgangsspannung direkt am
Verbraucher. Der Eingang bendet sich auf der Vorderseite des Gerätes.
Bedienung (HMI)
Die manuelle Bedienung erfolgt über eine farbige Anzeige, zwei Drehknöp-
fe und sechs Tasten. Das große Display zeigt alle wichtigen Soll- und Ist-
werte gleichzeitig und übersichtlich an. Weiterhin können über das HMI
(Human-machine interface) das gesamte Setup vorgenommen werden.
Die Anzeige ist mehrsprachig (Deutsch, Englisch, Russisch, Chinesisch).
Fernsteuerung & Konnektivität
Zur Fernsteuerung stehen optional erhältliche, durch den Anwender leicht
installierbare Schnittstellenkarten in drei Varianten zur Verfügung:
USB
USB + Ethernet
USB + Analog
Über die digitalen Schnittstellen (USB, Ethernet) können Windows-Anwen-
der die mitgelieferte Software „EA Power Control“ für einfache bis komple-
xe Tests nutzen. Sie bietet unter Anderem das sogenannte „Sequencing“,
welches halbautomatische Testabläufe durch Tabellensteuerung ermög-
licht.
AC supply
The equipment uses an active Power Factor Correction (short: PFC), ena-
bling worldwide use on a mains input from 90 V
AC
up to 264 V
AC
.
Auto-ranging power stage
All models are equipped with a exible auto-ranging out-
put stage which provides a higher output voltage at lower
output current, or a higher output current at lower output
voltage, always limited to the max. nominal output pow-
er. The maximum power set value is adjustable with these
models. Therefore, a wide range of applications can al-
ready be covered by the use of just one unit.
DC output
DC output voltages between 0...40 V and 0...200 V, output currents be-
tween 0...2 A and 0...40 A and output power ratings between 0...160 W and
0...640 W are available.
Current, voltage and power can thus be adjusted continuously between 0%
and 100%, no matter if manually or remotely controlled (analog or digital).
The output terminals are located on the front side of the devices.
Protective features
For protection of the equipment connected, it is possible to set an overvolt-
age protection threshold (OVP), as well as one for overcurrent (OCP) and
overpower (OPP).
As soon as one of these thresholds is reached for any reason, the DC output
will be immediately shut o and a status signal will be generated on the
display and via the interfaces. There is furthermore an overtemperature
protection, which will shut o the DC output if the device overheats.
Remote sensing
The standard sensing input can be connected directly to the load in order
to compensate voltage drops along the cables. If the sensing input is con-
nected to the load, the power supply will detect this and adjust the output
voltage automatically to ensure the accurate required voltage is available
at the load.
Handling (HMI)
Manual operation is done with a colour display, two rotary knobs and six
pushbuttons. The large display shows all relevant set values and actual
values at a glance. The whole setup is also done with the human-machine
interface. The display is multilingual (German, English, Russian, Chinese).
Remote control & connectivity
For remote control, there are three types of interface cards optionally avail-
able which can be quickly and easily installed by user on location:
USB
USB + Ethernet
USB + Analog
Using the digital interface (USB, Ethernet), Windows users can prot from
the free software “EA Power Control”. It oers a feature called “Sequenc-
ing”, where the device is controlled through a semi-automatic table in CSV
format.
P
Nom
I
Nom
100 %
50 %
100 %50 %
U
Nom
Auto-range
A
B
C
D
E