User Manual

Page 3
EA Elektro-Automatik GmbH
Helmholtzstr. 31-33 • 41747 Viersen
Germany
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
www.elektroautomatik.de
[e-mail]
ELR 9000 Series
TABLE OF CONTENTS
1
GENERAL
1.1 About this document........................................5
Retention and use ...........................................5
Copyright ..........................................................5
Validity .............................................................. 5
1.2 Explanation of symbols ...................................5
1.3 Warranty ..........................................................5
1.4 Limit of liability ..................................................5
1.5 Disposal of equipment ..................................... 6
1.6 Product key ...................................................... 6
1.7 Intended usage ................................................ 6
1.8 Safety ...............................................................7
Safety notices ..................................................7
Responsibility of the user ................................7
Responsibility of the operator .........................8
User requirements ...........................................8
Alarm signals ...................................................9
1.9 Technical Data .................................................9
Approved operating conditions .......................9
General technical data ....................................9
Specic technical data ...................................10
Views .............................................................. 16
1.10 Construction and function ...........................20
General description .......................................20
Block diagram ................................................20
Scope of delivery ...........................................21
Accessories ...................................................21
Options ........................................................... 21
The control panel (HMI) .................................22
USB-Port Type B (Back side) ........................25
Interface module slot .....................................25
Analog interface ............................................. 25
Share connector ............................................26
Sense connector (remote sensing) ............... 26
Master-Slave bus ...........................................26
2
INSTALLATION & COMMISSIONING
2.1 Transport and storage ...................................27
Transport ........................................................ 27
Packaging ......................................................27
Storage ..........................................................27
2.2 Unpacking and visual check .........................27
2.3 Installation ......................................................27
Safety procedures before installation and
use .................................................................27
Preparation ....................................................28
Installing the device .......................................28
Mains connection (AC) ..................................29
Connection to DC sources ............................30
Grounding of the DC input ............................31
Connection of remote sense .........................31
Connecting the “Share” bus ..........................32
Installation of an AnyBus interface module...32
Connecting the analog interface ...................33
Connecting the USB port (rear side) .............33
Initial commission ..........................................34
Commission after a rmware update or a long
period of non use ...........................................34
3
OPERATION AND APPLICATION
3.1 Personal safety ..............................................35
3.2 Operating modes ...........................................35
Voltage regulation / Constant voltage ...........35
Current regulation / constant current / current
limitation .........................................................35
Resistance regulation / constant resistance .36
Power regulation / constant power / power
limiting ............................................................36
Alarm conditions ............................................37
3.3 Manual operation ........................................... 38
Powering the device ......................................38
Switching the device off ................................. 38
Conguration via MENU................................38
Adjustment limits............................................45
Changing the operating mode ......................46
Manual adjustment of set values ..................46
Switching the DC input on or off....................47
3.4 Remote control ..............................................48
General ..........................................................48
Controls locations ..........................................48
Remote control via the digital interface .........48
Remote control via the analog interface (AI) 49
3.5 Alarms and monitoring ..................................52
Denition of terms ..........................................52
Device alarm handling ................................... 52
3.6 Control panel (HMI) lock ...............................54
3.7 Loading and saving a user prole ................. 55
3.8 The function generator ..................................56
Introduction ....................................................56
General ..........................................................56
Method of operation ......................................56
Manual operation ........................................... 57
Sine function ..................................................58
Triangular function .........................................59
Rectangular function .....................................59
Trapezoidal function ......................................60
DIN 40839 function ........................................ 60
Arbitrary function ............................................61
Ramp Function ..............................................65
UI and IU functions ........................................65
Remote control of the function generator .....66
3.9 Other applications ..........................................67
Parallel operation in master-slave (MS) .......67
Series connection ..........................................70
Two quadrant operation (2QO) .....................70