Installation & Assembly

Connect wires per wiring diagram as follows:
1. Connect the green or bare copper wall box wire to the terminal screw
marked "GR".
2. Connect common wire (Line hot or Load) to the terminal screw
marked "BK".
3. Connect the first traveler wire to the terminal screw marked "RD".
4. Remove insulating label and connect the second traveler wire to the
remaining terminal screw below marked "RD".
5. Form all wires carefully into wall box, mount dimmer but DO NOT
install wall plate with mounting screws supplied until all sections are
finished.
TROUBLESHOOTING
1. The dimmer doesn't turn on the light.
• Check that the bulb is installed and has not failed.
• Check if the circuit breaker or fuse is connected properly.
• Check if the neutral line of the lamp is connected properly.
2. The light flicker throughout the dimming range.
• Check if there is a dimmable sign on the CFL or LED and
make sure to use a dimmable CFL or LED light.
3. CFL or LED lights flicker at low brightness.
• Refer to step 8. Minimum Brightness Setting to turn up the
minimum brightness level until it doesn’t flicker.
4. The LED lamp turns on slightly after turning off the dimmer.
• Refer to step 9. Optional Locator Light to turn off the locator
light of the dimmer, or use a dimmable LED bulb.
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
SWITCH DIMMER
RD
Black Screw
(common)
RD
BK
Line
120VAC 60Hz
Load
Hot (Black)
Neutral (White)
GR
Ground
(Green)
3-Way Wiring5B.
Select Dimmer Mode Per Bulb Type Before Testing6.
Test Your Dimmer7.
Minimum Brightness Setting8.
Optional Locator Light9.
Dimmer Mounting10.
1. Press the PUSH tabs at both sides of the bottom and pull forward the top
cover to release.
2. This dimmer switch is pre-set at the factory with the Mode Switch set to
Mode L, which works for LED or incandescent light bulbs. For application
in controlling CFL light bulbs, set the Mode Switch to Mode C in the right
position.
2.5A 300W CFL/LED
600W INC
120VAC 60Hz
L: LED/INC
S: Set Mode
C: CFL
MODE
L S C
Mode Switch
PUSH Tab
PUSH Tab
Actuator
ON
OFF
Slider Bar
TOP
L: LED/INC
S: Set Mode
C: CFL
MODE
L S C
Actuator
ON
OFF
LOC
OFF ON
LOC
WARNING: TO PREVENT SEVERE SHOCK OR ELECTROCUTION,
MAKE SURE YOUR FINGERS DO NOT TOUCH THE WALL BOX,
WIRES OR THE SCREW TERMINALS WHEN POWER IS RESTORED!
1. Turn OFF power at the circuit breaker (or remove fuse).
2. Refer to CHANGE THE COLOR OF YOUR DIMMER section to mount the
top cover.
3. Mount the wall plate to the dimmer with the screws provided.
4. Turn ON power at the circuit breaker or restore fuse. Installation is complete.
NOTE: The locator light will never turn ON when the load light is ON.
By factory default, the white locator light (LOC) of the dimmer switch is
ON when the load light is OFF, and the locator light is OFF when the
load light is ON.
To turn off the locator light when the load light is OFF, move the LOC
Switch to the OFF position to disable it.
ONE YEAR LIMITED WARRANTY
The warranty gives you specific rights and you may also have other
rights, which vary in different states and countries. Our company
warrants to the original consumer purchaser that this product is free of
defects in materials and workmanship for 1 year from the purchase
date. This warranty does not cover labor for removal or
reinstallation of the product and is void on any product installed
improperly or in an improper environment, overloaded, misused,
opened, abused, or altered in any manner. Our company excludes
incidental or consequential damages for breach of any warranty on
this product. Some jurisdictions may not allow limitations on how long
an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above exclusions or limitations may
not apply to you.
Slide Bar
2.5A 300W CFL/LED
600W INC
120VAC 60Hz
1. Move the slide bar inside the
dimmer and the slide bar of the
color kit (top cover) to the bottom.
2. Insert tabs of the color kit into the
slots on the top of the dimmer.
3. Then press the bottom of the
color kit in until it snaps into place.
CHANGE THE COLOR OF YOUR DIMMER
If a color change kit is provided with your device, proceed with the
following steps if you need to change the color.
White Locator Light
LOC Switch
LOC
OFF ON
TOP
L: LED/INC
S: Set Mode
C: CFL
MODE
L S C
Actuator
ON
OFF
LOC
OFF ON
LOC
Top Cover is ON Top Cover is OFF
Top Cover is ON Top Cover is OFF
INSTALLATION INSTRUCTIONS
2.5A 300W CFL/LED
600W INC
120VAC 60Hz
ON
OFF
ON
OFF
L: LED/INC
S: Set Mode
C: CFL
L S C
MODE
PUSH
1. Make sure the light is on. If not, press & hold actuator to keep the
light on.
2. Set the Mode Switch to Mode S in the middle position.
3. Adjust the slide bar to desired minimum brightness.
4. For LED or incandescent light bulbs, set the Mode Switch back to
Mode L. For CFL light bulbs, set the Mode Switch to MODE C.
5. Release actuator to finish setting.
ON
OFF
1. Restore power at circuit breaker or fuse.
2. Move slider bar to the highest position
and press the actuator. Lights should
turn ON to brightest level.
3. If lights never turn ON, turn OFF the
power and recheck the wiring, or refer to
the TROUBLESHOOTING section.
ON
OFF
Actuator
OFF ON
LOC
Actuator
OFF
ON
OFF ON
LOC
OFF ON
LOC
OFF
ON
Actuator
L: LED/INC
S: Set Mode
C: CFL
MODE
L S C
L: LED/INC
S: Set Mode
C: CFL
MODE
L S C
ELE GROUP CO., LTD
NO.158 CHUANGYUAN RD, SIP
SUZHOU, JIANGSU, CHINA 215125
WWW.ELEGRP.COM