Use and Care Manual

In either A or B position, if the Left Dial is set to Auto (turned all the way to the far left past “L” to the “Auto“ position) then this
light will convert to operate as a traditional motion sensing light. In this SMART AUTO mode it will light up to full brightness
when motion is detected.
When the Left Dial is set at the AUTO position the illumination time has a fixed 60 second delay time for the light to be ON after
motion is detected and the lighting will be extended as long as motion is continually detected. It will not turn off until the motion
detection has stopped and after the illuminating Delay Time has expired.
The motion Sensitivity/Range can be adjusted using the Right Dial (Ref. Fig. 2, page 1), to set the desired Sensitivity/Range for
the application. This adjustment has a motion sensing range from Low 10’, Med. 35’, High 60’ (For most applications set the
dial to between M--H, in warmer temperature environmental locations set this slightly higher.)
Cautions: 1) Adjust the Sensitivity/Range so that it is not set too sensitive, this will increase false activations and reduce
stored battery energy. 2) If the IPM feature detects that the battery does not have enough stored energy to operate at full
brightness when set with the left dial in the SMART AUTO position then it will automatically reduce the light level to half
brightness in order to maintain a level of safe lighting until it again receives enough sunlight in good weather conditions to
restore it back to normal status.
Optimization of SMART Profiles Operation
eLEDing SMART Light user related additional information
Rev. EE814WDC 052015 Page 2
Fig.5 Table Stand & DC Power (option)
In SMART A or B profiles (switch position set to A or B position) the solar light operates as a true Dusk to Dawn light. The unit
senses its surrounding ambient light level and will turn on in darkness providing adjustable moonlight soft glow lighting all night
long. When motion is detected it lights up to it’s full brightness or pre-set max-brightness within the set sensitivity range. For
either new installations or replacing existing AC light applications the B position is the recommended SMART profile when used
as an outdoor or indoor light for Security and Safety. It can also be used to enhance CCTV applications by providing full color
white light image illumination for the area of camera coverage without AC/DC power source or power shortage limitations.
In SMART B profile the motion activated brightness level is controlled and set by the user. In this mode the Left Dial functions as
a Brightness adjusting dial for setting the light level from lowest (L) to highest (H) brightness. When motion is detected it will
brighten up to the level as pre-set by the Left Dial and when motion stops it will slowly dim down to the lowest factory
fixed pre-set moonlight soft glow lighting level. It is recommended that for most country locations with good sunshine that this
setting should be H, and for geographic locations with poor sunshine it should be set at a lower level between M to below H.
SMART B also allows the brightness level to be adjustable between L to M. Set the Right Dial to H when using the light as a
portable or table reading/studying light for outdoor or indoor use (Fig. 5).
Caution
- The higher the brightness level is set to the more stored battery energy is used when activated by motion. If the IPM
detects that the battery does not have enough capacity to run this mode it will automatically convert to AUTO mode for energy
saving and turn on only when motion is detected until it receives enough sunlight to operate the SMART feature correctly.
In SMART A profile the lower soft glow lighting level is controlled and set by the user. The Left Dial is used for setting the
dimming level of moonlight soft glow lighting from the level of lowest (L) to highest (H) brightness. When motion is detected the
light will brighten up to the factory fixed max full brightness level and then dim back down to the moonlight level set by the user. It
is recommended that for most country locations with good sunshine that this setting should be middle level M or less. For
locations with poor sunshine it should be set at a the lowest level L (or switch to SMART B profile is recommended).
SMART A with the Left Dial set at its highest (H) the light operates as a projecting spot light. In the H position with the battery
fully charged the light will be ON at its brightest illumination and it will provide continuous lighting for a time period of up to 8 hrs.
Caution
- The higher the minimum soft glow level is set to the more stored battery energy is used to provide soft glow lighting. If
the IPM detects that the battery does not have enough capacity to run this mode it will automatically convert to AUTO mode for
energy saving and turn on only when motion is detected until it receives enough sunlight to operate the SMART feature correctly.
In either SMART A or B profile, if user geographic location has outstanding daytime sunlight conditions all year (California,
Arizona, New Mexico, Florida of USA e.g.) then this SMART light provides a wide range of adjustability in lighting performance.
Using the SMART A profile you can increase the Moonlight Dusk-to-Dawn dimming level up to full-brightness as peak ON.
Using the SMART B profile you can increase up to Max-brightness on peak when motion is detected. For most applications
using the SMART B profile with the factory preset Dial settings is recommended.
In both A and B profile if the IPM detects that the battery does not have enough capacity to operate these modes in critical
weather conditions then it will convert to AUTO mode. And if the IPM detects that there is insufficient battery reserve to operate
in Auto mode then it will automatically disable illuminating functions leaving only the charger active to protect the battery from
over discharge causing damage. After enough sunlight is received to charge the battery, the unit will first return to AUTO mode
for motion activated lighting until it receives enough sunlight energy to operate the SMART profiles properly.
Our latest generation of software based eLEDing Solar-Hybrid powered Light offers three principal SMART operating profile modes. The
Sensitivity/Range of motion, length of illuminating time, and levels of brightness and dimming are set and controlled with adjustable dials.
(Fig. 2). The family of eLEDing solar lights use an exclusive Intelligent Power Management (IPM) embedded and self-compensated feature
for managing and optimizing the Lithium based battery (either Li-Poly or LiFePO4) for a full range of operation. This optimizes the battery’s
life cycle to adapt to most environmental conditions allowing both the battery and light to perform for many years.
X
Fig. 4 Unusual Positions